User`s guide
Table Of Contents
- Table of Contents
- Section1 Introduction
- Section2 Using SANbox Manager
- 2.1 Installing SANbox Manager
- 2.1.1 SANsurfer Management Suite Disk - Windows Installation
- 2.1.2 SANsurfer Management Suite Disk - Linux Installation
- 2.1.3 SANsurfer Management Suite Disk - Solaris Installation
- 2.1.4 SANbox2 Installation Disk - Windows Installation
- 2.1.5 SANbox2 Installation Disk - Linux Installation
- 2.1.6 SANbox2 Installation Disk - Solaris Installation
- 2.2 Starting SANbox Manager
- 2.3 Exiting SANbox Manager
- 2.4 Uninstalling SANbox Manager
- 2.5 Changing Default File Password
- 2.6 Setting Preferences
- 2.7 Using Online Help
- 2.8 Viewing Software Version and Copyright Information
- 2.9 SANbox Manager User Interface
- 2.10 Using the Topology Display
- 2.11 Using the Faceplate Display
- 2.1 Installing SANbox Manager
- Section3 Managing Fabrics
- 3.1 Security
- 3.2 Managing the Fabric Database
- 3.3 Replacing a Failed Switch
- 3.4 Displaying Fabric Information
- 3.5 Zoning a Fabric
- Section4 Managing Switches
- 4.1 Displaying Switch Information
- 4.2 Managing Alarms
- 4.3 Exporting Name Server Information to a File
- 4.4 Paging a Switch
- 4.5 Setting the Date and Time
- 4.6 Setting Temperature Thresholds
- 4.7 Resetting a Switch
- 4.8 Configuring a Switch
- 4.9 Archiving a Switch
- 4.10 Restoring a Switch
- 4.11 Managing Firmware
- 4.12 Restoring the Factory Default Configuration
- Section5 Managing Ports
- AppendixA Command Line Interface
- A.1 Logging On to a Switch
- A.2 Command Syntax
- A.3 Commands
- Admin Command
- Alias Command
- Config Command
- Date Command
- Fallback Command
- Help Command
- History Command
- Image Command
- Lip Command
- Passwd Command
- Ps Command
- Quit Command
- Reset Command
- Set Command
- Set Config Command
- Set Log Command
- Set Port Command
- Set Setup Command
- Show Command
- Show Config Command
- Show Log Command
- Show Perf Command
- Show Setup Command
- Shutdown Command
- Test Command
- Uptime Command
- User Command
- Whoami Command
- Zone Command
- Zoneset Command
- Zoning Command
- AppendixB Graphing Port Performance
- AppendixC Messages
- C.1 Fabrics File—Open, Save
- C.2 Add a Fabric
- C.3 Network Properties Dialog
- C.4 Switch Properties Dialog
- C.5 Port Properties Dialog
- C.6 Faceplate Display
- C.7 Firmware Fallback Dialog
- C.8 Load Firmware Dialog
- C.9 Port Loopback Test Dialog
- C.10 Extended Credits Dialog
- C.11 Zoning Dialog
- C.12 Restore Configuration Dialog
- C.13 Save Fabric View
- C.14 Trap Configuration Dialog
- Glossary
- Index
A – Command Line Interface
Set Config Command
A-26 59022-05 A
ALFairness Arbitration loop fairness. Enables (True)
or disables (False) the switch’s priority
to arbitrate on the loop.
ARB_FF Use ARB_FF instead of idles on loop
FCAL option
InteropCredit Interoperability credit. The number of
buffer-to-buffer credits per port. 0
means the default (12) is unchanged.
ExtCredit Extended credits. The number of port
buffer credits that this port can acquire
from donor ports.
FANEnable Fabric address notification. Enables
(True) or disables (False) the
communication of the FL_Port address,
port name, and node name to the
logged-in NL_Port.
LCFEnable Link control frame preference, R_CTL =
0xC
MFSEnable Multi-Frame Sequence bundling
MFS_TOV MFS limit for camp on
MSEnable Management Server enable on this port
NoClose Don't close unless another device
arbitrates
I/O Stream Guard Enables or disables the suppression of
RSCN messages
VIEnable Enable VI preference routing
CheckAlps Close before sending frames to new
target
Table A-7. Set Config Port Parameters (Continued)
Parameter Description