User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
7 – SANsurfer iSCSI/FC Router Manager
Tool Bar
FI0054601-00 C 7-9
A
Add Remote Router Wizard – Launches the Add Remote Router Wizard,
which allows you to assign local router to a remote router as peers (see
page 7-68).
Remove Remote Router Wizard – Launches the Remove Remote Router
Wizard, which allows you to remove a local-to-remote router peer
assignment (see page 7-72).
Map Remote Initiator/Target Wizard – Launches the Map Remote
Initiator/Target Wizard, which allows you to map an initiator to a target
device, one of which is on a remoter router (see page 7-75).
Unmap Remote Initiator/Target Wizard – Launches the Remote Mapped
Device, which allows you to delete an initiator-to-target device mapping (see
page 7-81).
Discover iSCSI Target – Launches the Discover iSCSI Target Wizard,
which allows you to specify the IP address of the iSCSI Target to be
discovered. The target is added to the discovered targets list (see
page 7-84).
FCIP Route Add – Launches the FCIP Route Add Wizard wizard, which
allows you to select the resources used for the route, the IP address of the
remote FCIP peer, IP parameters, VLAN support, compression and
bandwidth limit (see page 7-86).
FCIP Route Remove – Launches the FCIP Route Remove Wizard wizard,
which allows you to remove an existing FCIP Route freeing the resources
(FC and GE ports) used by the route. (See page 7-92).
FW Update Wizard – Launches the FW Update Wizard, which allows you to
update the router’s firmware (see page 7-51).
Add Initiator Wizard – Launches the Add Initiator Wizard, which allows you
to enter an iSCSI initiator into the system database (see page 7-49).
Remove Initiator – Removes the selected iSCSI initiator. This option is
available only when an initiator is selected (highlighted) in the system tree.
Remove Offline Target – Removes the selected offline Fibre Channel
target. This option is available only when an offline FC target is selected
(highlighted) in the system tree.
Beacon ON – Turns on the SANbox 6142 router beacon to locate the router
quickly.
Beacon OFF – Turns off the SANbox 6142 router beacon.