User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
7 – SANsurfer iSCSI/FC Router Manager
Tool Bar
FI0054601-00 C 7-7
A
Help Menu
Figure 7-8 shows the Help menu. The following paragraphs describe it.
Figure 7-8 Help Menu
Set Browser Location – Allows you to specify the browser that launches when
you view the online help for the SANsurfer iSCSI/FC Router Manager.
Browse Contents – Launches the online help for the SANsurfer iSCSI/FC Router
Manager.
About – Displays the application version information.
Tool Bar
Figure 7-9 shows the tool bar. The following paragraphs describe it.
Figure 7-9 Tool Bar
The tool bar consists of a row of graphical buttons that allow you to perform
common functions – connect, view log files, and refresh the current display. You
can move the tool bar in the display by clicking and dragging the handle at the tool
bar’s left edge.
Connect – Adds a SANbox 6142 router to the system tree view.
View Logs – Opens a window to display the system log data.
Refresh – Updates the display with current information.