User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
B – Log Messages
Fatal Log Messages
FI0054601-00 C B-29
A
102749 #%d: QLProcessResponseQueueFS: Invalid handle 0x%x, type
0x%x
349
102752 #%d: QLTimer: Ext Ram parity error exceed limit cnt 0x%x, limit
0x%x, Disabled adapter
352
102755 #%d: QLTimer: Heartbeat failed 355
102800 #%d: QLRestartRisc: restart RISC 400
19 FC1 processor SRAM test failed.
20 FC1 processor power-on self-test (POST) failed.
21 FC2 processor SRAM test failed.
22 FC2 processor POST failed.
23 FC processor failed to return diagnostic results.
256 FC processor failed reset.
257 FC processor firmware load failed.
258 FC processor receive sequencer code load failed.
259 FC processor transmit sequencer code load failed.
262 FC processor firmware checksum failed.
280 FC processor firmware initialization failed.
288 FC processor paused due to internal parity error.
289 FC processor returned an invalid interrupt status.
291 FC processor invalid interrupt status.
292 FC processor paused due to RAM parity error.
316 FC processor system error.
346 Response queue entry contains an invalid handle.
347 FCIP: Response queue entry contains an invalid buffer type.
348 FCIP: Response queue entry contains an invalid entry type.
349 FCIP: Response queue entry contains an invalid handle.
Table B-14. Fibre Channel Driver—Fatal Log Messages (Continued)
ID Log Message No.