User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
B – Log Messages
Fatal Log Messages
FI0054601-00 C B-27
A
20 iSCSI processor SRAM test failed.
21 iSCSI processor failed diagnostic reboot.
22 iSCSI processor failed NVRAM diagnostic.
23 iSCSI processor failed DRAM diagnostic.
24 iSCSI processor failed to return diagnostic results.
309 Response queue entry contains an invalid handle.
319 Set NVRAM reboot timer failed.
332 Port disable reboot timer failed.
334 Port enable reboot timer failed.
592 iSNS response contains an invalid handle.
768 Start iSCSI processor failed.
785 iSCSI processor firmware initialization failed.
800 iSCSI processor port fatal error.
816 Start iSCSI processor reboot timer failed.
857 iSCSI processor fatal system error.
867 Response queue invalid handle for ET pass-through.
869 Response queue invalid entry type.
870 Response queue invalid handle for specified entry type.
892 Asynchronous event for unknown event type.
912 Reboot timer failed.
931 iSCSI driver missed iSCSI processor heartbeat. iSCSI processor rebooted.
932 iSCSI processor failed to complete operation before timeout.
977 iSCSI processor system error restart.
978 iSCSI processor reboot failed.
1152 iSCSI processor NVRAM invalid (checksum error).
1203 iSCSI FLASH (NVRAM) command failed.
1204 iSCSI firmware loader invalid state.
1205 iSCSI failed to load firmware in time allotted.