User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index

B – Log Messages
Fatal Log Messages
B-26 FI0054601-00 C
S
69964 #%d: QLDisable: QLRebootTimer failed AF %x RS %x Time %d 332
69966 #%d: QLEnable: QLRebootTimer failed AF %x RS %x Time %d 334
70224 #%d: QLProcSrblessiSNSResponse: Invalid handle %x 592
70400 #%d: QLInitializeDevice: QLStartAdapter failed 768
70417 #%d: QLInitializeAdapter: QLInitializeFW failed 785
70432 #%d: QLDoInterruptServiceRoutine: PortFatal interrupt.
PortFatalErrorStatus %08x CSR %08x AS %x AF %x
800
70448 #%d: QLStartAdapter: QLRebootTimer failed AF %x RS %x
Time %d
816
70489 #%d: QLIsrDecodeMailbox: System Error 8002 MB[1-7] %04x
%04x %04x %04x %04x %04x %04x
857
70499 #%d: QLProcessResponseQueue: Invalid handle for
ET_PASSTHROUGH_STATUS
867
70501 #%d: QLProcessResponseQueue: Invalid entry type in response
queue %x
869
70502 #%d: QLProcessResponseQueue: Invalid handle %x
EntryType %x
870
70524 #%d: QLProcessAen: Invalid event %x 892
70544 #%d: QLRebootTimer: Reboot failed! 912
70563 #%d: QLReadyTimer: Adapter missed heartbeat for 0x%x
seconds. Rebooting
931
70564 #%d: QLReadyTimer: Abort pTpb=%p failed, DrvCount 0x%x 932
70609 #%d: QLProcessSystemError: Restart RISC 977
70610 #%d: QLProcessSystemError: RebootHba failed 978
70784 #%d: QLConfigChip: invalid NVRAM 1152
70835 #%d: QLStartFw: MBOX_CMD_SET_FLASH failed %x 1203
70836 #%d: QLStartFw: Invalid Fw loader state 0x%x 1204
70837 #%d: QLStartFw: Load Fw loader timeout 1205
Table B-13. iSCSI Driver—Fatal Log Messages (Continued)
ID Log Message No.