User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
B – Log Messages
Error Log Messages
B-18 FI0054601-00 C
S
iSCSI Driver
The following error log messages are common to both iSCSI ports, 1 (GE1) and 2
(GE2). They are listed in Tabl e B- 9 and described following the table. Log
messages beginning with #0 denote iSCSI port 1 (GE1). Log messages beginning
with #1 denote iSCSI port 2 (GE2).
Table B-9. iSCSI Driver—Error Log Messages
ID Log Message No.
73990 #%d: QLUtmIoctlEnable: Initialize FW failed 262
74046 #%d: QLPortUp: MBOX_CMD_SET_PORT_CONFIG %04x
failed %04x
318
74056 #%d: QLRunDiag: MBOX Diag test internal loopback
failed %x %x
328
74057 #%d: QLRunDiag: MBOX Diag test external loopback
failed %x %x
329
74065 #%d: QLPortDown: MBOX_CMD_SET_PORT_CONFIG %04x
failed %04x
337
74241 #%d: QLiSNSEnableCallback: iSNS Server TCP Connect failed 513
74577 #%d: QLIsrDecodeMailbox: NVRAM invalid 849
74587 #%d: QLIsrDecodeMailbox: Link down 859
74656 #%d: QLReadyTimer: Adapter missed heartbeat for %d sec-
onds. Time left %d
928
74661 #%d: QLTimer: Abort pTpb=%p, Type %x, Timeout 0x%x Drv-
Count 0x%x, DdbIndex 0x%x
933
74663 #%d: QLReadyTimer: MBOX_CMD %04x %04x %04x %04x
%04x %04x %04x %04x timed out
935
74665 #%d: QLReadyTimer: QLiSNSReenable failed. 937
74784 #%d: QLUpdateInitiatorData: No more room in Initiator Data-
base.
1056
74800 #%d: QLSetTargetData: No more room in Target Database. 1072
262 The iSCSI processor failed firmware initialization.
318 The iSCSI processor command to enable a GE port failed.
328 The iSCSI processor failed the internal loopback test.