User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index

B – Log Messages
Error Log Messages
FI0054601-00 C B-13
A
43280 QLFCIP_HandleTeb: Driver Fatal error 2320
43281 QLFCIP_ConfigPortal: Find portal object failed for
QLUT_TYPE_FC, PortId (%d)
2321
43282 QLFCIP_ConfigPortal: QLFCIP_ConfigPortal: Invalid PortId for
FCIP link PortID(%d)
2322
43283 QLUT_AllocateFcipTrbPool: Allocation failed (size 0x%x)) 2323
43284 QLUT_GetFcipTrb: Null portal object in map table 2324
43285 QLUT_GetFcipTrb: Unable to get the Free Trb 2325
43286 QLUT_GetFcipTrb: Duplicate allocation of FcipTrb (0x%p) 2326
43287 QLUT_FreeFcipTrb: Null portal object in map table 2327
43288 QLUT_FreeFcipTrb: Duplicate Free of FcipTrb (0x%p) 2328
43289 QLUT_InitializeFcipBufDescPool: Memory allocation for
FCIP_BUF_EXT_DESC failed (size 0x%x)
2329
43296 QLUT_FreeFcipDataBuffers: Duplicate Freeing of DataBuf
(0x%p)
2336
43297 QLUT_AllocateFcipDataBuffers: Duplicate allocation of
DataBuffer (0x%p)
2337
43298 QLUT_AllocateFcipDataBuffer: Got NULL PORTAL Object in map
table MEM LEAK!!!!!
2338
43299 QLUT_DeallocateFcipDataBuffer: Null portal object in map table 2339
43300 QLUT_CreateFcipDataBufferpool: Allocation of 32K buffers from
LargeBufferPool failed
2340
43521 QLSC_BreakupVUIOAllocPhase: TPB allocation failed 2561
43522 QLSC_BreakupVUIOAllocPhase: Data buffer and TPB allocation
failed
2562
7 NULL doorbell routine for unloaded drivers. When a driver is unloaded, the
doorbell routine is redirected to this NULL routine.
36 Processing unsupported ordered tag task management command.
44 Processing unsupported head-of-queue task management command.
Table B-8. Application Module—Error Log Messages (Continued)
ID Log Message No.