User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index

B – Log Messages
Error Log Messages
B-12 FI0054601-00 C
S
42024 QLFC_Logout: No active path to device. WWPN:
%.2X%.2X%.2X%.2X%.2X%.2X%.2X%.2X
1064
42027 QLFC_Logout: VP Index 0x%x not configured 1067
42068 QLFC_HandleTeb: System Error 1108
42069 QLFC_HandleTeb: Driver Fatal Error 1109
42072 QLFC_HandleTeb: FC Logout 1112
42242 QLIS_AllocateSessionObject: Out of session resources 1282
42252 QLIS_EnqueueiScsiPdu: Duplicate PDU, CmdSN %d (0x%x),
dropping it
1292
42258 QLIS_InstantiateSession: Can't add Initiator to the database 1298
42404 QLIS_ProcessStartTrb: [%d] CmdSN %ld is out of range (%ld
- %ld), Cdb[0] 0x%02X, DataXferLen 0x%x.
1444
42648 QLIS_HandleTeb: Driver Fatal Error 1688
42649 QLIS_HandleTeb: Unload Driver 1689
42654 QLIS_HandleTeb: iSNS Connection Failed 1694
43012 QLSC_CollectBUVUIO: Allocation of DSD failed 2052
43013 QLSC_CollectBUVUIORecover: Allocation of DSD failed 2053
43265 QLUT_AllocateTpbExtension: TPB allocation failed 2305
43267 QLUT_AllocateTpbExtension: Data buffer allocation failed (length
%d)
2307
43268 QLUT_AllocateTpbExtension: Alloc of DSD failed for buffer len
%d
2308
43269 QLFCIP_IncomingFrame: BUGCHECK: Trb (0x%p) ValidFlag
(0x%x) Direction (0x%x)
2309
43270 QLFCIP_IncomingFrame: GetFcipMapPortal failed 2310
43271 QLFCIP_IncomingFrame: Got Status aborted
pTrb->pBufDescList[0]:%p Trb Direction:0x%x
2311
43272 QLFCIP_SystemError: System error 2312
43273 QLFCIP_SystemError: QLOP_IssuePortEnable failed 2313
Table B-8. Application Module—Error Log Messages (Continued)
ID Log Message No.