User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
B – Log Messages
Error Log Messages
FI0054601-00 C B-11
A
41270 QLIS_LoginPduContinue: TSIH is 0 but InitiatorName key/value
not provided
310
41272 QLIS_LoginPduContinue: CONN_STATE_IN_LOGIN, Unknown
InitTaskTag
312
41283 QLIS_LoginPduContinue: TSIH 0x%x out of range 323
41284 QLIS_LoginPduContinue: Session does not exist, invalid TSIH
0x%x
324
41353 QLIS_LoginPduContinue CHAP Validation Failure 393
41354 QLIS_LoginPduContinue Unexpected CHAP key detected 394
41508 QLBI_SetPortInfo: QLUT_AllocatePortalObject failed (PortType
0x%x, PortId 0x%x)
548
41626 QLBI_GetLunInfo: INQUIRY failed, TPB status 0x%x 666
41629 QLBI_GetLunInfo: QLBI_PassthruCommand failed for INQUIRY
(page code 0x83)
669
41635 QLBI_GetLunInfo: QLBI_PassthruCommand failed for READ
CAPACITY
675
41636 QLBI_GetLunInfo: READ CAPACITY failed, TPB status 0x%x 676
41696 QLBI_PassthruCommandCompletion: Passthru command
aborted
736
41700 QLBI_Passthru: Invalid CDB length %d bytes 740
41701 QLBI_Passthru: Invalid data length %d bytes 741
41717 QLBI_PassthruCommand: command interrupted or timed out 757
41750 QLBI_Ioctl: ERROR: Operation (0x%x) not supported in this mode 790
41768 QLBI_GetLunList: REPORT LUNS command failed 808
41769 QLBI_GetLunList: REPORT LUNS command failed with CHECK
CONDITION, SCSI STATUS 0x%02X
809
41771 QLBI_GetLunList: Lun allocation failed for LunId %d 811
41994 QLFC_Login: VpIndex (%d) out of range 1034
41995 QLFC_Login: VP Index 0x%x not configured 1035
42002 QLFC_Login: Can't open connection 1042
Table B-8. Application Module—Error Log Messages (Continued)
ID Log Message No.