User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
B – Log Messages
Informational Log Messages
B-8 FI0054601-00 C
S
FCIP
The FCIP module generates the informational log messages listed in Table B-5
and described following the table.
348 Remotemap removed for local FC device WWPN xx.xx.xx.xx.xx.xx.xx.xx.
349 Remotemap removed for remote FC device WWPN xx.xx.xx.xx.xx.xx.xx.xx.
350 Localmap added for FC initiator WWPN xx.xx.xx.xx.xx.xx.xx.xx.
351 Localmap added to FC target device WWPN xx.xx.xx.xx.xx.xx.xx.xx.
352 Localmap removed for FC initiator.
353 Localmap removed to FC target device.
354 Localmap added for iSCSI initiator "iqn.dddd-dd.ttt.ttt.ttt.......".
355 Localmap removed for iSCSI initiator "iqn.dddd-dd.ttt.ttt.ttt.......".
356 User enabled GE port d.
357 User disabled GE port d.
358 User enabled FC port d.
359 User disabled FC port d.
517 FCIP route #d added.
518 FCIP route #d modified.
519 FCIP route #d removed.
Table B-5. FCIP—Informational Log Messages
ID Log Message No.
184524 qlFcip_Linkchange#%d: GigE Link Down 204
184525 qlFcip_Linkchange#%d: GigE Link Up 205
204 FCIP Route GigE link d (1 or 2) is down.
205 FCIP Route GigE link d (1 or 2) is up.