User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index

B – Log Messages
Informational Log Messages
FI0054601-00 C B-7
A
151903 qapimaptargettoinitiator_1_svc: Localmap added to target device
%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x
351
151904 qapiunmaptargettoinitiator_1_svc: Localmap removed for initiator
device %.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x
352
151905 qapiunmaptargettoinitiator_1_svc: Localmap removed to target
device %.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x
353
151906 qapimaptargettoinitiator_1_svc: Localmap added for initiator %s 354
151907 qapiunmaptargettoinitiator_1_svc: Localmap removed for initiator
%s
355
151908 GE%d: Port status changed by user to ENABLED. 356
151909 GE%d: Port status changed by user to DISABLED. 357
151910 FC%d: Port status changed by user to ENABLED. 358
151911 FC%d: Port status changed by user to DISABLED. 359
152069 qapisetfcipparams_1_svc: FCIPROUTE %d Added 517
152070 qapisetfcipparams_1_svc: FCIPROUTE %d Modified 518
152071 qapisetfcipparams_1_svc: FCIPROUTE %d Removed 519
290 Performed router firmware upgrade, new version number is d.d.d.d.
291 User performed a router reboot or shutdown.
337 FC port configuration has been modified.
338 iSCSI port configuration has been modified.
339 iSNS configuration has been modified.
340 NTP configuration has been modified.
341 VLAN configuration has been modified.
344 Management ethernet port configuration has been modified.
345 Router configuration has been modified.
346 Remotemap added for local FC device WWPN xx.xx.xx.xx.xx.xx.xx.xx.
347 Remotemap added for remote FC device WWPN xx.xx.xx.xx.xx.xx.xx.xx.
Table B-4. User Modules—Informational Log Messages (Continued)
ID Log Message No.