User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index

B – Log Messages
Informational Log Messages
B-2 FI0054601-00 C
S
54306 QLFC_Logout: Origin 0x%x, VP Index 0x%x, Id 0x%x 1058
54307 QLFC_Logout: Port ID %.2x%.2x%.2x 1059
54308 QLFC_Logout: Node Name
%.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x
1060
54309 QLFC_Logout: Port Name
%.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x
1061
54359 QLFC_HandleTeb: FC Login. VP 0x%x 1111
54368 QLFC_CreateVirtualInitiatorObject: Maximum host (%d) limit
reached.
1120
54938 QLIS_HandleTeb: UTM_EC_OPEN_CONNECTION 1690
54939 QLIS_HandleTeb: UTM_EC_CLOSE_CONNECTION or
UTM_EC_CONNECTION_CLOSED
1691
54940 QLIS_HandleTeb: UTM_EC_CONNECTION_OPENED 1692
54941 QLIS_HandleTeb:iSNS Server Open Connection succeeded 1693
54943 QLIS_HandleTeb: UTM_EC_ISNS_SCN 1695
54945 QLIS_HandleTeb: UTM_EC_ISNS_CLIENT_DISCOVERED 1697
54947 QLIS_HandleTeb: UTM_EC_CLOSE_CONNECTION 1699
54948 QLIS_HandleTeb: UTM_EC_CONNECTION_CLOSED 1700
54963 QLIS_SetDdbEntryContinue:[%d:%d] Remote system connection
established
1715
54986 QLIS_HandleSessionTimer: Re-enabling compression 1738
55299 QLSC_CollectBUVUIO: Freeing dead TRB: State 0x%02X,
AbortReason %d, Flags 0x%02X
2051
6 Router is booting up.
109 De-compression failed and will be temporarily disabled.
1026 FC login occurred, origin xx (1 = HBA, 2 = target, 3 = initiator), VP (virtual port)
xx, ID (loop ID) xx.
1027 FC login occurred with port ID xx.xx.xx.
Table B-1. Application Modules—Informational Log Messages (Continued)
ID Log Message No.