User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
A – Command Reference
Commands
A-60 FI0054601-00 C
S
IPv6 Link Local fe80::2c0:ddff:fe0c:8be2
IPv6 Default Router ::
IPv6 Target TCP Port No. 3260
IPv6 Window Scaling Enabled
IPv6 Window Scaling Factor 1
IPv6 VLAN Disabled
iSCSI Port 2
Port Status Enabled
Link Status Up
iSCSI Base Name
iqn.2004-08.com.qlogic:isr-6142.0608a00471.1
MAC Address 00-c0-dd-0c-8b-e3
IP Address 0.0.0.0
Subnet Mask 0.0.0.0
Gateway IP Address 0.0.0.0
Firmware Revision No. 3.00.02.44
No. of Open Connections 0
Target TCP Port No. 3260
MTU Size Normal
Window Size 32768
Window Scaling Enabled
Window Scaling Factor 1
Current Port Speed 1Gb/FDX
Programmed Port Speed Auto
Header Digests Enabled
Data Digests Enabled
Max Burst 262144
Max First Burst 65536
VLAN Disabled
IPv6 Address 1 ::
IPv6 Address 2 ::
IPv6 Link Local fe80::2c0:ddff:fe0c:8be3
IPv6 Default Router ::
IPv6 Target TCP Port No. 3260
IPv6 Window Scaling Enabled
IPv6 Window Scaling Factor 1
IPv6 VLAN Disabled