User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
A – Command Reference
Commands
A-28 FI0054601-00 C
S
Remote Map Command
The remotemap command provides for the mapping of an initiator and target, one
of which is located on a remote system (router). It prompts you to enter the remote
system (router), then lists the devices (initiators and targets) located on the
remote system. You can select a device from the remote system and then the
local system.
Authority Admin session
Syntax remotemap
add
mod
rm
Keywords add
Adds a device mapping, initiator to target, one of which is remote.
mod
Modifies an existing remote device mapping.
rm
Removes a remote device mapping.
Examples Remotemap add command example:
QRouter (admin) #> remotemap add
The following wizard will create a mapping a device connected to the
local system and a device connected to the selected remote peer
system. If you wish to terminate this wizard before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
Index (System Info, Mgmt IP Address)
----- ------------------------------
0 iSR-6142.0608A00487(172.17.137.215)
Please select a REMOTE system from the list above ('q' to quit) : 0
Index (WWNN,WWPN/iSCSI Name)
----- ----------------------
0 20:20:00:d0:b2:02:86:d0,21:20:00:d0:b2:02:86:d0 (Init/Tgt)
1 20:21:00:d0:b2:02:86:d0,21:21:00:d0:b2:02:86:d0 (Init/Tgt)
2 20:20:00:d0:b2:02:86:d1,21:20:00:d0:b2:02:86:d1 (Init/Tgt)
3 20:21:00:d0:b2:02:86:d1,21:21:00:d0:b2:02:86:d1 (Init/Tgt)
Please select a LOCAL device from the list above ('q' to quit) : 0