User`s guide
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 General Description
- 3 Planning
- 4 Installation
- Site Requirements
- SANbox 6142 Router Installation
- Pre-installation Check List
- Mount the Router
- Install the Transceivers
- Connect the Management Workstation to the Router
- Configure the Management Workstation
- Install SANsurfer iSCSI/FC Router Manager
- Start SANsurfer iSCSI/FC Router Manager
- Connect the Router to AC Power
- Configure the Router
- Cable Devices to the Router
- Firmware Installation
- 5 Diagnostics and Troubleshooting
- 6 Removal/Replacement
- 7 SANsurfer iSCSI/FC Router Manager
- Introduction
- Menu Bar
- Tool Bar
- System Tree Window
- Wizards
- Configuration Wizard
- Add Initiator Wizard
- FW Update Wizard
- Map Local Initiator/Target Wizard
- Unmap Local Initiator/Target Wizard
- Add Remote Router Wizard
- Remove Remote Router Wizard
- Map Remote Initiator/Target Wizard
- Unmap Remote Initiator/Target Wizard
- Discover iSCSI Target Wizard
- FCIP Route Add Wizard
- FCIP Route Remove Wizard
- A Command Reference
- Logging On to a SAN Router
- Guest Account
- Working with SAN Router Configurations
- Commands
- Admin Command
- Beacon Command
- Clear Command
- Date Command
- FcipRoute Command
- FRU Command
- Help Command
- History
- Image Command
- Initiator Command
- Localmap Command
- Logout Command
- Password Command
- Ping Command
- Quit Command
- Reboot Command
- Remote Map Command
- Remote Peer Command
- Reset Factory Command
- Save Command
- Set Command
- Set CHAP Command
- Set FC Command
- Set Features Command
- Set iSCSI Command
- Set iSNS Command
- Set Mgmt Command
- Set NTP Command
- Set Properties Command
- Set SNMP Command
- Set System Command
- Show Command
- Show CHAP Command
- Show FC Command
- Show FcipRoutes Command
- Show Features Command
- Show Initiators Command
- Show iSCSI Command
- Show iSNS Command
- Show Localmaps Command
- Show Logs Command
- Show Memory Command
- Show Mgmt Command
- Show NTP Command
- Show Performance Command
- Show Presented Initiators Command
- Show Presented Targets Command
- Show Properties Command
- Show Remotemaps Command
- Show Remotepeers Command
- Show SNMP Command
- Show Stats Command
- Show System Command
- Show Targets Command
- Show VLAN Command
- Shutdown Command
- Target Command
- Traceroute Command
- B Log Messages
- C Configuring CHAP
- D Simple Network Management Protocol (SNMP)
- Index
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
FI0054601-00 C 7-25
A
iSCSI Port Network Settings
Port Status – When the port link is up, you can enable or disable the port
using this drop-down list.
IPv4 Address – When using an IPv4 address scheme, define the following
fields:
IP Address – The IP address to which the port responds. An
un-initialized port has an IP address of all zeros. Although you may
modify the IP address in this window, you will typically set it using the
Configuration Wizard.
Subnet Mask – The subnet mask used by the port. Although you may
modify the subnet mask in this window, you will typically set it using the
Configuration Wizard.
Gateway – The gateway for the selected port.
VLAN – The VLAN configuration: Disabled or Enabled. You can
configure VLAN from this window.
VLAN ID – When VLAN is enabled the VLAN ID contains an
identification value in the range 0 to 4094. You can configure VLAN
from this window.
Priority – When VLAN is enabled, this field defines the priority
assigned to this VLAN. To set the priority, open the drop-down menu
and select the desired value (between 0 to 7).
IPv6 Address – When using an IPv6 address scheme, define the following
fields:
IPv6 Address1 – The first user-assigned IPv6 address to which the
port responds. A value of :: indicates that an IPv6 address has not
been assigned. Although you may modify the IP address in this
window, you will typically set it using the Configuration Wizard.
IPv6 Address2 – The second user-assigned IPv6 address to which
the port responds. A value of :: indicates that an IPv6 address has not
been assigned. Although you may modify the IP address in this
window, you will typically set it using the Configuration Wizard.
IPv6 Default Router – Use this address to set the default router for the
IPv6. The system can also set the IPv6 default router dynamically
depending on your network configuration.
IPv6 Local Link – This field contains the IPv6 link local address of the
port. It is not editable.
VLAN IPv6 – The VLAN IPv6 configuration: Disabled or Enabled. You
can configure VLAN from this window.