SANbox 6140 Intelligent Storage Router User’s Guide FI0154601-00 C
S SANbox 6140 Intelligent Storage Router User’s Guide Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for illustrative purposes only.
S SANbox 6140 Intelligent Storage Router User’s Guide Removed reference to SANsurfer application installation from a CD; replaced CD installation procedures with steps for downloading software from the QLogic website Section 4 Corrected information on LED diagnostics to identify the blink patterns that display on the System Fault LED, not the Heartbeat LED Section 5 Updated screens and descriptions regarding IP addresses to include IPv6 options in SANsurfer iSCSI/FC Router Manager Section 7 Added ic
SANbox 6140 Intelligent Storage Router User’s Guide S Notes Page iv FI0154601-00 C
A SANbox 6140 Intelligent Storage Router User’s Guide Table of Contents 1 Introduction Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Communications Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SANbox 6140 Intelligent Storage Router User’s Guide S Fibre Channel Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fibre Channel Port LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fibre Channel Transceivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gigabit Ethernet Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ethernet Port—Management . . . . . . . . . . . . . . .
A SANbox 6140 Intelligent Storage Router User’s Guide Install SANsurfer iSCSI/FC Router Manager. . . . . . . . . . . . . . . . . . . . Windows Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Linux Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Start SANsurfer iSCSI/FC Router Manager. . . . . . . . . . . . . . . . . . . . . Connect the Router to AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configure the Router . .
SANbox 6140 Intelligent Storage Router User’s Guide S Status Icons and Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FC and iSCSI Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Discovered iSCSI Initiators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FC Discovered Targets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A SANbox 6140 Intelligent Storage Router User’s Guide A Command Reference Logging on to a SAN Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Guest Account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Working with SAN Router Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . Modifying a Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SANbox 6140 Intelligent Storage Router User’s Guide S Show Initiators Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Show Initiators LUN Mask Command . . . . . . . . . . . . . . . . . . . . . . . . . Show iSCSI Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Show iSNS Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Show Logs Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A SANbox 6140 Intelligent Storage Router User’s Guide Application Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iSCSI Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fibre Channel Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . User Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System. . . . . . . . . . . . . . . . . . . . . . . . . . . .
SANbox 6140 Intelligent Storage Router User’s Guide 7-4 7-5 7-6 7-7 7-8 7-9 7-10 7-11 7-12 7-13 7-14 7-15 7-16 7-17 7-18 7-19 7-20 7-21 7-22 7-23 7-24 7-25 7-26 7-27 7-28 7-29 7-30 7-31 7-32 7-33 7-34 7-35 7-36 7-37 7-38 7-39 7-40 7-41 7-42 7-43 7-44 7-45 7-46 7-47 7-48 Page xii S View Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A 7-49 7-50 7-51 7-52 7-53 7-54 7-55 7-56 7-57 7-58 7-59 7-60 7-61 7-62 7-63 7-64 SANbox 6140 Intelligent Storage Router User’s Guide Confirm Changes Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Security Check Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Firmware Update Status Dialog Box—Progress . . . . . . . . . . . . . . . . . . . . . . . . . . . Finish Dialog Box (Successful Firmware Update) . . . . .
SANbox 6140 Intelligent Storage Router User’s Guide S Notes Page xiv FI0154601-00 C
1 Introduction This manual describes the features and installation of the QLogic SANbox 6140 Intelligent Storage Router (iSR-6140), also referred to as the SANbox 6140 router or simply router. Intended Audience This guide is for users who are responsible for installing, managing, and servicing the SANbox 6140 router and the storage area network (SAN) equipment to which it is attached. Related Materials Internet Protocol, Version 6 (IPv6) Specification., RFC2460.
S 1 – Introduction Safety Fibre Channel Physical and Signaling Interface (FC-PH), X3.230:199 Fibre Channel 2nd Generation (FC-PH-2), X3.297:1997 Third Generation Fibre Channel Physical and Signaling Interface (FC-PH-3), X3.303:1998, Fibre Channel-Arbitrated Loop (FC-AL-2), working draft, revision 6.
A 1 – Introduction Communications Statements Federal Communications Commission (FCC) Class A Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
S 1 – Introduction Laser Safety Information IEC1000-4-2:1995 - "Electrostatic Discharge Immunity Test" IEC1000-4-3:1995 - "Radiated, Radio-frequency, Electromagnetic Field Immunity Test" IEC1000-4-4:1995 - "Electrical Fast Transient/Burst Immunity Test" IEC1000-4-5:1995 - "Surge Immunity Test" IEC1000-4-6:1996 - "Immunity To Conducted Disturbances, Induced By Radio-Frequency Fields" IEC1000-4-8:1993 - "Power Frequency Magnetic Field Immunity Test" IEC1000-4-11:1994 - "Voltage Di
A 1 – Introduction Electrostatic Discharge Sensitivity (ESDS) Precautions Electrostatic Discharge Sensitivity (ESDS) Precautions The assemblies used in the router chassis are ESD sensitive. Observe ESD handling procedures when handling any assembly used in the router chassis.
S 1 – Introduction General Public License Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software - to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it.
A 1 – Introduction General Public License of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you".
1 – Introduction General Public License S These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works.
A 1 – Introduction General Public License If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 5. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License.
1 – Introduction General Public License S It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices.
A 1 – Introduction General Public License IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 14.
S 1 – Introduction General Public License How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program.
A 1 – Introduction Technical Support This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Library General Public License instead of this License. Technical Support Customers should contact their authorized maintenance provider for technical support of their QLogic switch products.
S 1 – Introduction Technical Support Contact Information Please feel free to contact your QLogic approved reseller or QLogic Technical Support at any phase of integration for assistance. QLogic Technical Support can be reached by the following methods: Web http://support.qlogic.com North America Contact Information Email support@qlogic.com Phone (952) 932-4040 Support contact information for other regions of the world is available at the QLogic website: http://support.qlogic.
2 General Description This section describes the following features and capabilities of the SANbox 6140 router: Chassis LEDs (see page 2-2) Chassis Controls (see page 2-3) Fibre Channel Ports (see page 2-5) Fibre Channel Transceivers (see page 2-6) Gigabit Ethernet Port LEDs (see page 2-7) Ethernet Port—Management (see page 2-7) Serial Port (see page 2-8) Figure 2-1 illustrates many of these features.
S 2 – General Description Chassis LEDs Chassis LEDs The chassis LEDs shown in Figure 2-2 provide information about the router’s operational status. These LEDs include the input power LED, heartbeat LED, and the system fault LED. To apply power to the router, plug the power cord into the router AC power receptacle and into a 100-240 VAC power source. Figure 2-2 Chassis LEDs Heartbeat LED (Green) The heartbeat LED blinks once a second as long the router firmware is operational.
A 2 – General Description Chassis Controls Chassis Controls The maintenance button shown in Figure 2-3 is the only chassis control. Press this button to reset the router or to recover the router if it becomes disabled. Figure 2-3 Chassis Controls Maintenance Button The maintenance button is a multifunction momentary switch on the front panel.
S 2 – General Description Chassis Controls Reset and Select Boot Image You can reset the router using either the primary or secondary boot image: Primary Image – To reset the router and select the primary boot image, use a pointed, nonmetallic tool to press and hold the maintenance button until the heartbeat LED flashes once, then release the button. The router will boot from the primary boot image. The boot time is less than one minute.
A 2 – General Description Fibre Channel Ports Erases all presentations. Erases all discovered initiators and targets. Fibre Channel Ports The SANbox 6140 router has two Fibre Channel 1-Gbps/2-Gbps ports. The ports are labeled FC1 and FC2, as shown in Figure 2-4. Figure 2-4 Fibre Channel LEDs Each port is served by a small form-factor pluggable (SFP) optical transceiver and is capable of 1-Gbps or 2-Gbps transmission. SFPs are hot-pluggable.
S 2 – General Description Fibre Channel Transceivers Table 2-2.
A 2 – General Description Gigabit Ethernet Port LEDs Gigabit Ethernet Port LEDs The Gigabit Ethernet ports shown in Figure 2-5 are RJ-45 connectors that provide connection to an Ethernet SAN through a 10/100/1000 Base-T Ethernet cable. The ports are labeled GE1 and GE2. Each of these ports supports connections that run the iSCSI high-level TCP protocol.
S 2 – General Description Serial Port The management Ethernet port has two LEDs: The link status LED (green) lights up continuously when the port establishes an Ethernet connection. The activity LED (green) lights up when the port transmits or receives data over the Ethernet connection. Serial Port The SANbox 6140 router is equipped with an RS-232 serial port for maintenance purposes. Figure 2-7 shows the serial port location, which is labeled IOIOI.
3 Planning This section describes how to plan for the SANbox 6140 router.
S 3 – Planning Device Access Device Access Consider device access needs within the FC and iSCSI SANs. Controlling access to FC device LUNs requires mapping FC device LUNs to specific iSCSI initiators. You may map LUNs to more than one initiator. Giving multiple initiators access to a LUN requires access management. Fibre Channel The Fibre Channel ports automatically discover all FC target devices, whether connected directly (loop) or by fabric (switch).
A 3 – Planning iSCSI Performance Beyond these distances, however, the connection loses some efficiency because the transmitting port must wait for an acknowledgement before sending the next frame. Bandwidth Bandwidth is a measure of the volume of data that can be transmitted at a given transmission rate. A 1-Gbps/2-Gbps FC port can transmit or receive at nominal rates of 1- or 2-Gbps, depending on the device to which it is connected.
S 3 – Planning Performance Tuning Performance Tuning Proper configuration maximizes the router’s performance. Knowing the round trip delay (distance between the router and iSCSI initiators) and WAN effective data rate (connection type) allows you to tune the router for optimal performance. The following tables provide TCP Window Size settings for specific WAN environments. The TCP Window Size is configured as two parameters: Window Size and Scaling Factor.
A 3 – Planning Performance Tuning Table 3-2. T3 / DS-3: 45 Mbits/Sec (Continued) Round Trip Delay (ms) TCP Window Size (bytes) SANbox 6140 Window Size SANbox 6140 Scaling Factor 15 64-128 K 32K 1 or 2 10 64 K 32K 1 5 32 K 32K 0 2.5 32 K 32K 0 1 or less 32 K 32K 0 Table 3-3.
S 3 – Planning Performance Tuning Table 3-4. OC-1: 50 Mbits/Sec (Continued) Round Trip Delay (ms) TCP Window Size (bytes) SANbox 6140 Window Size SANbox 6140 Scaling Factor 50 256 K 32K 3 25 128 K 32K 2 20 128 K 32K 2 15 64-128 K 32K 1 or 2 10 64 K 32K 1 5 32 K 32K 0 2.5 32 K 32K 0 1 or less 32 K 32K 0 Table 3-5.
A 3 – Planning Multiple Routers Table 3-6. OC-12 and Above: 621 Mbits/Sec Round Trip Delay (ms) TCP Window Size (bytes) SANbox 6140 Window Size SANbox 6140 Scaling Factor 250 1 MB 32K 5 100 1 MB 32K 5 50 1 MB 32K 5 25 1 MB 32K 5 20 1 MB 32K 5 15 1 MB 32K 5 10 1 MB 32K 5 5 512 K 32K 4 2.
S 3 – Planning Recovery Recovery It is prudent to have a process in place to recover from a possible router failure.
A 3 – Planning Security Security Passwords provide router security. The SANsurfer Router Manager requires a password each time a user logs into the application. Once connected, the SANsurfer Router Manager prompts for an administrative password before it accepts configuration changes. The CLI also requires the user to enter a user ID and password to start. CLI must be in an admin session to perform any set operations. An admin session requires a password.
S 3 – Planning Security Notes 3-10 FI0154601-00 C
4 Installation This section describes how to install, configure, and recover a disabled SANbox 6140 router. It also provides firmware installation instructions.
S 4 – Installation Site Requirements Table 4-1. Management Workstation Requirements (Continued) Item Internet browser Description One of the following: Microsoft Internet Explorer 5.0 and later Netscape Navigator® 4.72 and later Mozilla® 1.02 and later Safari™ Java 2 runtime environment to support the web applet Power Requirements Power requirements for the SANbox 6140 router are 0.5 Amp at 100 VAC or 0.25 A at 240 VAC.
A 4 – Installation Installing the SANbox 6140 Router Installing the SANbox 6140 Router Unpack the router and accessories. The SANbox 6140 router is shipped with the following components, shown in Figure 4-1. Power cord Dongle for connecting the router’s serial port to a workstation used for configuring and managing the router. A standard Cat5 Ethernet cable is required (not supplied) to connect the dongle to the router. The dongle connects directly to the workstation’s serial (COM) port.
S 4 – Installation Installing the SANbox 6140 Router Pre-installation Check List During the initial configuration process, the system prompts you to enter the parameters listed in Table 4-2. Fill out the table before installation to expedite the configuration process. Table 4-2.
A 4 – Installation Installing the SANbox 6140 Router NOTE: The transceiver fits only one way. If the transceiver does not install under gentle pressure, flip it over and try again. Connect the Management Workstation to the Router You can manage the router using the SANsurfer iSCSI/FC Router Manager or the command line interface (CLI). SANsurfer iSCSI/FC Router Manager requires an Ethernet connection to the router. CLI can use an Ethernet connection or a serial connection.
S 4 – Installation Installing the SANbox 6140 Router Setting the Workstation IP Address The IP address of a new router is 10.0.0.1. To ensure that your workstation is configured to communicate with the 10.0.0 subnet, refer to the following instructions for your workstation: Steps for different versions of Windows vary. For a Windows 2000 workstation, do the following: a. From the Windows Start menu, select Settings>Control Panel>Network and Dial-up Connections. b. Click Make New Connection. c.
A 4 – Installation Installing the SANbox 6140 Router For Linux: a. Set up minicom to use the serial port. Create or modify the /etc/minirs.dfl file with the following content: pr portdev/ttyS0 pu minit pu mreset pu mhangup pr portdev/ttyS0 specifies port 0 on the workstation. Choose the pr setting to match the workstation port to which you connected the router. b. Verify that all users have permission to run minicom. Review the /etc/minicom.
4 – Installation Installing the SANbox 6140 Router S Linux Installation Perform the following steps to install the SANsurfer iSCSI/FC Router Manager application from the QLogic website to a Linux workstation: 1. Go to the QLogic download site: http://support.qlogic.com/support/drivers_software.aspx 2. Select the Intelligent Storage Routers icon. 3. Select SANbox 6140 in the product selection window and click Go. 4.
A 4 – Installation Installing the SANbox 6140 Router Connect the Router to AC Power WARNING!! This product is supplied with a 3-wire power cable and plug for the user’s safety. Use this power cable in conjunction with a properly grounded outlet to avoid electrical shock. An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the router chassis. The customer must make sure the outlet is correctly wired and grounded to prevent electrical shock.
S 4 – Installation Installing the SANbox 6140 Router To configure the router using the command line interface: 1. Open a command window according to the type of workstation and connection: Ethernet (all platforms): Open a telnet session with the default router IP address and log in to the router with the default account name and password (guest/password): telnet 10.0.0.1 username: guest password: ******** Serial – Windows: Open the HyperTerminal application on a Windows platform: a.
A 4 – Installation Firmware Installation Firmware Installation The router comes with current firmware installed. You can upgrade the firmware from the management workstation as new firmware becomes available. You can use the SANsurfer iSCSI/FC Router Manager application or the CLI to install new firmware. WARNING!! Installing new firmware disrupts the router connectivity since you must reboot the router to activate the new firmware.
S 4 – Installation Firmware Installation 3. At the ftp prompt, type bin to set binary mode. For example: ftp> bin 200 Type set to I. 4. Use the put command to transfer the firmware image file from the workstation to the router. For example: ftp> put isr-6140-2_0_6_3.bin 200 PORT command successful. 150 Opening BINARY mode data connection for 'isr-6140-2_0_6_3.bin'. 226 Transfer complete. ftp: 4822816 bytes sent in 0.41Seconds 11878.86Kbytes/sec. 5. Enter quit.
5 Diagnostics and Troubleshooting Diagnostic information about the router is available through the chassis LEDs and the port LEDs. Diagnostic information is also available through the SANsurfer iSCSI/FC Router Manager and Command Line Interface (CLI) event logs and error displays.
5 – Diagnostics and Troubleshooting Power-On Self-Test Diagnostics S Input Power LED is Off The input power LED lights up to show that the router logic circuitry is receiving proper voltages. If the input power LED is off, do the following: Inspect power cord and connectors. Is the cord unplugged? Is the cord or connector damaged? Yes – Make necessary corrections or repairs. If the condition remains, continue. No – Continue. Inspect AC power source.
A 5 – Diagnostics and Troubleshooting LED Blink Patterns LED Blink Patterns The heartbeat and system fault LEDs show the operational status of the router. When the POST completes with no errors, these LEDs blink at a steady rate of once per second. When the router is in maintenance mode, the heartbeat and system fault LEDs are on continuously. All other system fault blink patterns show critical errors. The heartbeat LED shows an error blink pattern for the conditions listed in Table 5-1. Table 5-1.
5 – Diagnostics and Troubleshooting LED Blink Patterns S Management Port IP Address Conflict Blink Pattern The system fault LED generates a four-blink pattern (once per second) followed by a two second pause when the router detects an IP address conflict on the management Ethernet port. You can clear the IP address conflict blinking using the CLI or SANsurfer Router Manager. Use the beacon OFF function.
A 5 – Diagnostics and Troubleshooting Recovering a Router Recovering a Router You may have to recover a router for one of the following reasons: The password was changed and has been forgotten. The router’s management IP address is unknown. To recover the router’s password, reset the password to the default by using the maintenance button (see page 2-3).
5 – Diagnostics and Troubleshooting Recovering a Router S Notes 5-6 FI0154601-00 C
6 Removal/Replacement This section describes how to remove and replace the following field replaceable units (FRU): SFP transceivers Router SFP Transceiver Removal and Replacement You can remove and replace the SFP transceivers while the router is operating without damaging the router or the transceiver. However, this interrupts transmission on the affected port until you install the transceiver.
6 – Removal/Replacement Router Removal and Replacement S Router Removal and Replacement The router removal and replacement procedure requires the router powered down, which means that all of the Fibre Channel and iSCSI connections will be lost. Removal To remove and replace a router, follow the applicable steps: 1. Make sure that all traffic (I/O operations to the router) is quiescent at the iSCSI initiator systems. 2.
7 SANsurfer iSCSI/FC Router Manager Introduction The SANsurfer iSCSI/FC Router Manager provides a graphical user interface (GUI) that enables you to manage the SANbox 6140 from a workstation. This lets you monitor, configure, and modify information using GUI components, including a menu bar, a tool bar, a system tree, as well as information, status, and data windows and tabs, as illustrated in Figure 7-1 and described in Table 7-1.
S 7 – SANsurfer iSCSI/FC Router Manager Menu Bar Table 7-1. SANsurfer Router Manager Main Window Sections Item Description Menu Bar The menu bar provides access to system functions and Wizards. Tool Bar The tool bar buttons provide quick access to the common application functions—Connect, View Logs, and Refresh. Action Menu Right-click anywhere inside the system tree window to open the action menu. This menu provides a shortcut to actions available elsewhere in the SANsurfer Router Manager.
A 7 – SANsurfer iSCSI/FC Router Manager Menu Bar File Menu Figure 7-3 shows the File drop-down menu. Figure 7-3 File Menu The File menu provides the following options: Save FRU – Saves the router’s configuration and persistent data to a file. Restore FRU – Restores the router’s configuration and persistent data from a file. Exit – Exits the SANsurfer iSCSI/FC Router Manager. View Menu Figure 7-4 shows the View drop-down menu.
7 – SANsurfer iSCSI/FC Router Manager Menu Bar S The Settings menu provides the following option: Broadcast – Opens the Broadcast Settings window, which allows you to configure the broadcast options. The workstation sends Broadcast messages to locate routers within the same IP subnet as the workstation running the SANsurfer Router Manager application. Figure 7-6 shows the Broadcast Settings dialog box. Figure 7-6 Broadcast Settings Menu The following paragraphs describe its options.
A 7 – SANsurfer iSCSI/FC Router Manager Menu Bar Add Initiator Wizard – Launches the iSCSI Add Initiator wizard, which allows you to configure the IP address and other parameters for an iSCSI initiator (see page 7-52). FW Update Wizard – Launches the Firmware Update wizard, which allows you to update the SANbox 6140 router’s firmware image. You can select the firmware image from a dialog box that allows browsing (see page 7-54).
S 7 – SANsurfer iSCSI/FC Router Manager Tool Bar Tool Bar Figure 7-9 shows the tool bar. The following paragraphs describe it. Figure 7-9 Tool Bar The tool bar consists of a row of graphical buttons that allow you to perform common functions: connect, view log files, and refresh the current display. You can relocate the tool bar on the screen by clicking and dragging the handle at the left edge of the tool bar. Connect button – Adds a SANbox 6140 router to the system tree.
A 7 – SANsurfer iSCSI/FC Router Manager Action Menu Disconnect – Disconnects from a SANbox 6140 router, removing it from the system tree. Reboot – Reboots the SANbox 6140 router. View Logs – Opens the view logs window. Presentation Wizard – Launches a wizard for presenting (mapping) LUNs to iSCSI initiators (see page 7-64). Presentation Unmap Wizard – Launches a wizard for unmapping LUNs from iSCSI initiators (see page 7-64).
7 – SANsurfer iSCSI/FC Router Manager System Tree Window S System Tree Window Figure 7-11 shows the system tree.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window Select a component in the system tree to see component data in the tabbed pages to the right of the tree (see Figure 7-12). Figure 7-12 Component Information Component information for the selected router includes router information, configuration details, router status, and lists of connected or discovered devices.
S 7 – SANsurfer iSCSI/FC Router Manager System Tree Window Router Located at the root folder within the system tree, each router node shows: Router status icon – Live (blinking heart beat). Router name – Router name or IP address. Example: Router iSR-6140:10.3.13.90 Router icons Online router - The blinking heart on the router icon indicates that the connection between the SANsurfer Router Manager and the agent is active for this router.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window Initiator icons iqn.nnnn-nn.com.xxxxx:xxxnnnn - Initiator connection. To determine the connection status, select the initiator node in the system tree. On the initiator's Information tabbed page, the Status field identifies the status as either Logged In or Logged Out.
S 7 – SANsurfer iSCSI/FC Router Manager System Tree Window SANbox 6140 Router The top of the router tree displays the router system configuration and status. Selecting the Router node on the system tree displays the following two tabs: Information SNMP Management Information The Information tabbed page provides four vertical tabs with icons that identify its content: Basic Information, Management Information, NTP Server Information, and Security.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window Basic Information The Basic Information tabbed page provides the following parameters: Product Name – Model iSR6140. Symbolic Name – Displays a symbolic name for the router that you can create. Serial Number – Displays the router’s serial number. IQN uses Symbolic Name – Lets you enable or disable the use of the symbolic name in the router’s iSCSI name. Hardware Version – Identifies the router hardware version number.
S 7 – SANsurfer iSCSI/FC Router Manager System Tree Window Management Information Select the second vertical tab on the router’s Information tabbed page to display the Management Information tabbed page. Figure 7-14 Information Tabbed Page - Management Information The Management Information tabbed page provides the following parameters: MAC Address – Displays the management port’s MAC address. Link Status – Displays the management port link status: Link UP or Link Down.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window If you selected the Use the following IP address radio button, you can configure the IP address. Subnet Mask – Displays the management port’s subnet mask. If you selected the Obtain an IP address automatically (DHCP), the system obtains the subnet mask automatically through DHCP. If you selected the Use the following IP address radio button, you can configure the subnet mask.
S 7 – SANsurfer iSCSI/FC Router Manager System Tree Window NTP Server Information Select the third vertical tab on the router’s Information tabbed page to display the NTP Server Information tabbed page. Figure 7-15 Information Tabbed Page - NTP Server Information The NTP Server Information tabbed page provides the following parameters: 7-16 NTP Server Radio Buttons – Use these buttons to disable or enable the use of NTP servers to set the router’s date and time.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window NTP Server 3 – Displays the IP address of the third NTP server to be queried by the router when setting its time and date. This server is used only if the first and second NTP servers did not respond. If your hardware supports IPv6, you may choose the appropriate IP protocol of the NTP server, either IPv4 or IPv6, then enter the IP address using the appropriate notation.
S 7 – SANsurfer iSCSI/FC Router Manager System Tree Window SNMP Management The SNMP Management tabbed page consists of two sections: SNMP Configuration and SNMP Trap Receivers. Click the Save button to save any SNMP management changes. For more information, see Appendix D. Figure 7-17 shows the SNMP Management tabbed page.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window SNMP Settings Read Community – Enter a password that authorizes an SNMP management server to read information from the router. This is a write-only field. The value on the router and the SNMP management server must be the same. The read community password can be up to 32 characters excluding #, semicolon (;), and comma (,). The default is public. Trap Community – Enter a password that authorizes an SNMP management server to receive traps.
S 7 – SANsurfer iSCSI/FC Router Manager System Tree Window FC Ports When you select an FC port in the system tree, the Information tabbed page displays, as shown in Figure 7-18.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window Actual Data Rate – The data rate at which the port operates when on-line. This value can be one of the following: 1 Gbps - one gigabits per second 2 Gbps - two gigabits per second Save – If you change the Port Status, click this button to save your changes. A warning message opens, asking you to verify that you want to change this status. Click Yes to proceed or click No to cancel changing the status.
S 7 – SANsurfer iSCSI/FC Router Manager System Tree Window 2. Frame Size – Select the frame size from the drop-down list box: 512, 1024, or 2048. Execution Throttle – Select the execution throttle from the drop-down list box: 16, 32, 64, 128, or 256. Click Save. A Warning screen displays the following message: Changing the following port settings might cause a loss of connection to one or more ports. Do you want to proceed with the save operation? NOTE: To abort this process, click No. 3.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window Statistics The Statistics tabbed page consists of a scrollable table of parameters and values, as shown in Figure 7-20. Figure 7-20 FC Port Statistics To refresh the statistics, click Refresh at the top of the screen. To clear the statistics (set the values to zero), click Clear.
7 – SANsurfer iSCSI/FC Router Manager System Tree Window S iSCSI Ports When you select an iSCSI port in the system tree, the Information, Advanced Configuration, and Statistics tabbed pages display to the right of the tree, as shown in Figure 7-21. The following sections describe these pages.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window iSCSI Port Information The iSCSI Port Information area provides the following parameters: Base Name – Full name assigned to the selected iSCSI port. Link Status – Identifies the port connection status: Link Up or Link Down. MAC Address – The MAC address assigned to the port. The MAC address is not changeable. Actual Link Rate – Displays the actual link rate, which can be Unknown, 1000 Mbps, 100 Mbps, or 10 Mbps.
7 – SANsurfer iSCSI/FC Router Manager System Tree Window S Subnet Mask – The subnet mask used by the port. Although you may modify the subnet mask in this window, you will typically set it using the Configuration Wizard. Gateway – The gateway for the selected port. VLAN – The VLAN configuration: Disabled or Enabled. You can configure VLAN from this window. VLAN ID – When VLAN is enabled the VLAN ID contains an identification value in the range 0 to 4094.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window Enable iSNS Enable iSNS – This check box enables or disables iSNS support. Select the check box to enable this option; clear the check box to disable it. IP Server – This drop-down list box lets you choose the IP address version assigned to the IP server. The following examples show the IP address fields that open when you choose one of these options.
7 – SANsurfer iSCSI/FC Router Manager System Tree Window S Advanced Configuration The Advanced Configuration tabbed page allows you to configure the router’s port parameters, security settings, and CHAP settings. Figure 7-24 shows the information displayed in these sections. Figure 7-24 Advanced Configuration Tabbed Page The Advanced Configuration tabbed page consists of three sections: Port, Security, and CHAP settings.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window Target TCP Port Number – Identifies the TCP port number the iSR-6140 uses to receive iSCSI target commands. The iSCSI community uses TCP port number 3260 by default. Any change to this TCP port number requires a corresponding change in all iSCSI initiators connecting to this iSCSI target port. Jumbo Frame – Enables or disables iSR-6140 jumbo frame size as the maximum transfer unit (MTU).
7 – SANsurfer iSCSI/FC Router Manager System Tree Window S CHAP Secret – Lets you define the CHAP secret used for authenticating an iSCSI client. The field is available only when the CHAP check box is checked. NOTE: To apply any changes made to this screen, click the Save button, located at the bottom of window. Statistics The Statistics tabbed page consists of a scrollable table of parameters and values.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window Figure 7-25 Discovered iSCSI Initiator Tabbed Pages Information The Information tabbed page consists of two sections: Initiator Information and CHAP Settings. Initiator Information The Initiator Information section provides the following parameters: iSCSI IP Address – Displays the IP address of the discovered iSCSI initiator. iSCSI Alias – Displays the iSCSI initiators alias, which the initiator provides when it logs into the iSR-6140.
7 – SANsurfer iSCSI/FC Router Manager System Tree Window S OS Type Selection – Provides a drop-down list box you can use to select the OS type for the discovered initiator. The iSR-6140 uses the OS type to enable OS-specific commands. The menu options include: Other, MS Windows, Linux, HPUX, Mac, Solaris, VMware, and OpenVMS. Status – Displays activity status for the selected initiator.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window LUN List The LUN List tabbed page consists of a scrollable list of LUNs mapped to the iSCSI initiator, as shown in Figure 7-26. Figure 7-26 LUN List Tabbed Page The LUN List tabbed page provides the following options: Device Info – Displays information provided by the target LUN as a result of issuing a SCSI Inquiry command. Name – Displays the target name. For FC targets, the name is the WWPN. LUN – Displays the logical unit number.
S 7 – SANsurfer iSCSI/FC Router Manager System Tree Window FC Discovered Targets Selecting an FC discovered target in the system tree does not provide any information in the right window. Select a discovered FC target to display the Information, LUN List, and iSCSI Presented Target List tabbed pages to the right of the system tree, as shown in Figure 7-27.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window Port Name – Displays the world-wide port name of the target device. Port ID – Displays the target device’s port ID. LUN List The LUN List tabbed page provides detailed target information and a scrollable list of LUNs, as shown in Figure 7-28.
7 – SANsurfer iSCSI/FC Router Manager System Tree Window S Vendor – Displays the vendor name of the LUN as reported by the SCSI Inquiry command. Product ID – Displays the product ID of the LUN as reported by the SCSI Inquiry command. Product Rev – Displays the product revision of the LUN as reported by the SCSI Inquiry command.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window Device Port Name – Displays the world-wide port name of the target device. Device Port ID – Displays the target device’s port ID. Presented Port – Displays the iSCSI port number where the target is presented (1 or 2). IP Address – Displays the IP address on which the target is presented. Alias – Displays the iSCSI alias of the presented target. iSCSI Name – Displays the presented target’s iSCSI name.
7 – SANsurfer iSCSI/FC Router Manager System Tree Window 7-38 S Device Product Rev – Displays the product revision of the target device as reported by the SCSI Inquiry command. Device Node Name – Displays the world-wide node name of the target device. Device Port Name – Displays the world-wide port name of the target device. Device Port ID – Displays the target device’s port ID. Product Vendor – Displays the vendor name of the LUN as reported by the SCSI Inquiry command.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window LUN Presentation Information: 1 and 2 Tabbed Pages The LUN Presentation Information: 1 and LUN Presentation Information: 2 tabbed pages display information for the selected LUN. These pages include a list of iSCSI initiators that have been mapped to the selected (highlighted) LUN. Figure 7-31 shows the LUN Presentation Information: 1 tabbed page.
7 – SANsurfer iSCSI/FC Router Manager System Tree Window S Product ID – Displays the product ID of the LUN as reported by the SCSI Inquiry command. Product Revision – Displays the product revision of the LUN as reported by the SCSI Inquiry command. LUN – Displays the logical unit number. Mapped Initiator List—Address – Displays a list of IP addresses for the iSCSI initiators mapped to this LUN.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window Information Tabbed Page The Information tabbed page consists of two sections: General Information and CHAP Settings, which are described in the following paragraphs. General Information Product Vendor – Displays the product vendor as reported by the SCSI Inquiry command. Product ID – Displays the product ID as reported by the SCSI Inquiry command.
S 7 – SANsurfer iSCSI/FC Router Manager System Tree Window LUN Presentation Information Tabbed Page The LUN Presentation Information tabbed page provides presentation information for the selected LUN, as shown in Figure 7-33. This page includes a list of iSCSI initiators that have been mapped to the selected (highlighted) LUN.
A 7 – SANsurfer iSCSI/FC Router Manager System Tree Window Product ID – Displays the product ID of the LUN as reported by the SCSI Inquiry command. Product Rev – Displays the product revision of the LUN as reported by the SCSI Inquiry command. Discovered LUN Information Figure 7-34 shows the Discovered LUN Information tabbed page, which provides information for the selected LUN.
S 7 – SANsurfer iSCSI/FC Router Manager Wizards Device Port ID – Displays the target device’s port ID. Port: the FC port where the target device was discovered. Product Vendor – Displays the vendor name of the LUN as reported by the SCSI Inquiry command. Product ID – Displays the product ID of the LUN as reported by the SCSI Inquiry command. Product Revision – Displays the product revision of the LUN as reported by the SCSI Inquiry command. LUN – Displays the logical unit number.
A 7 – SANsurfer iSCSI/FC Router Manager Wizards FW Update Wizard – Use this wizard to update the SANbox 6140 router firmware. For more information, see page 7-54. Presentation Wizard – Launches the Presentation wizard. For more information, see page 7-58. Presentation Unmap Wizard – Launches the Presentation Unmap wizard. For more information, see page 7-64.
S 7 – SANsurfer iSCSI/FC Router Manager Wizards To configure the iSCSI ports using this wizard: 1. Select the radio button next to the iSCSI port you want to configure, then click Next. The iSCSI Port Connection Settings Panel dialog box displays, as shown in Figure 7-37. Figure 7-37 iSCSI Port Connection Settings Panel Dialog Box 2. 3. 7-46 Enter the information in the following fields, then click Next. IP Address Subnet Mask Gateway Click Next.
A 7 – SANsurfer iSCSI/FC Router Manager Wizards The iSCSI Port IPv6 Settings Panel appears, as shown in Figure 7-38. Figure 7-38 iSCSI Port IPv6 Settings Panel 4. To configure the iSCSI port IPv6 connection using this dialog box, follow these steps: a. Select Enable IPv6 Address to make the fields editable. b. Specify the iSCSI port IPv6 network settings: Enter the IPv6 Address 0. Enter the IPv6 Address 1. Enter the IPv6 Default Router. Enter the IPv6 Link Local. c.
7 – SANsurfer iSCSI/FC Router Manager Wizards S The Confirm Changes dialog box displays, as shown in Figure 7-39. Figure 7-39 Confirm Changes Dialog Box 6. 7-48 Review the configuration changes displayed on the screen, then click Next to confirm your changes.
A 7 – SANsurfer iSCSI/FC Router Manager Wizards The wizard displays a Warning message, as shown in Figure 7-40. Figure 7-40 Confirm Changes - Warning Message 7. Click Yes to confirm these changes. A Security dialog box prompts you to enter an administrative password. Figure 7-41 Security Check Dialog Box 8. FI0154601-00 C Enter the password, then click OK.
S 7 – SANsurfer iSCSI/FC Router Manager Wizards The system displays the iSCSI Port Configuration Status dialog box, as shown in Figure 7-42. Figure 7-42 iSCSI Port Configuration Status 9. Read the information about the status changes, then click Next. The system displays the Refresh dialog box. 10. 7-50 Read the information. If you would like to see the new configuration, click Yes; otherwise, click No.
A 7 – SANsurfer iSCSI/FC Router Manager Wizards The system displays the Finish dialog box, as shown in Figure 7-43. Figure 7-43 Configuration Wizard Finish Dialog Box 11. Read the information, then click Finish.
7 – SANsurfer iSCSI/FC Router Manager Wizards S Add Initiator Wizard The Add Initiator wizard provides a dialog box used to enter an iSCSI initiator into the system database. iSCSI initiators are normally discovered (the router captures their names and addresses) the first time they log in to the SANbox 6140 router. This wizard allows you to enter the initiator information before the log in, thus allowing you to map LUNs to the initiator before they log into the SANbox 6140 router.
A 7 – SANsurfer iSCSI/FC Router Manager Wizards The Security Check dialog box displays, as shown in Figure 7-45. Figure 7-45 Security Check Dialog Box 2. Enter the appropriate password, then click OK. The new iSCSI initiator appears in the discovered iSCSI initiators section of the system tree, as shown in Figure 7-46.
7 – SANsurfer iSCSI/FC Router Manager Wizards S FW Update Wizard The FW Update Wizard provides a set of dialog boxes that walk you through the steps required for updating the SANbox 6140 router firmware. You can start this wizard at any time by selecting FW Update Wizard from the Wizards Menu or from the Action Menu.
A 7 – SANsurfer iSCSI/FC Router Manager Wizards To update the firmware, follow these steps: 1. Select the check box next to the routers whose firmware you want to update, then click Next. The Open dialog box displays. Figure 7-48 Firmware File Selection Dialog Box 2. Enter in the path to the firmware file, or click Browse to locate the firmware file. 3. When the firmware file is displayed in the Firmware Image File field, click Next on the Firmware File Selection screen.
7 – SANsurfer iSCSI/FC Router Manager Wizards S The Confirm Changes dialog box displays, as shown in Figure 7-49. Figure 7-49 Confirm Changes Dialog Box 4. Read the information, then do the following: a. If you want to save a copy of this firmware configuration, click Save Configuration to File. Browse to the desired directory, type a file name, then click Save. b. Click Next. The Security Check dialog box requests the Admin password, as shown in Figure 7-50. Figure 7-50 Security Check Dialog Box c.
A 7 – SANsurfer iSCSI/FC Router Manager Wizards Figure 7-51 Firmware Update Status Dialog Box—Progress When the firmware has loaded successfully, the system displays the Finish dialog box, along with the Update success dialog box, as shown in Figure 7-52.
7 – SANsurfer iSCSI/FC Router Manager Wizards S NOTE: The new firmware will not take effect until the system is rebooted. 6. Complete the wizard: a. If you want to reboot the system now, click Yes. Otherwise, click No. b. Click Finish. Presentation Wizard The Presentation wizard provides step-by-step instructions for mapping target LUNs to iSCSI initiators. NOTE: Initially, when Fibre Channel targets are presented as iSCSI targets, the target’s LUNs are not accessible by iSCSI initiators.
A 7 – SANsurfer iSCSI/FC Router Manager Wizards To map a LUN to an iSCSI initiator: 1. Select the check box next to the LUN on the target you want to map, then click Next.
S 7 – SANsurfer iSCSI/FC Router Manager Wizards The LUN Mapping dialog box displays, as shown in Figure 7-54. Figure 7-54 LUN Mapping Dialog Box 2. Select one or more LUNs and iSCSI initiators you want mapped, then click Next. The Confirm Changes dialog box displays, as shown in Figure 7-55.
A 7 – SANsurfer iSCSI/FC Router Manager Wizards Figure 7-55 Confirm Changes Dialog Box 3. Confirm the LUN mapping changes by clicking Next. The Security Check dialog box displays, as shown in Figure 7-56. Figure 7-56 Security Check Dialog Box 4. Enter the appropriate password, then click OK to confirm the mapping. The LUN Masking Configuration Status dialog box displays, as shown in Figure 7-57, displaying the operation status.
S 7 – SANsurfer iSCSI/FC Router Manager Wizards Figure 7-57 LUN Masking Configuration Status Dialog Box 5. Review the status, then click Next. The Target Configuration Status dialog box displays, as shown in Figure 7-58. Figure 7-58 Target Configuration Status Dialog Box The Finish dialog box displays, as shown in Figure 7-59.
A 7 – SANsurfer iSCSI/FC Router Manager Wizards Figure 7-59 Finish Dialog Box 6. FI0154601-00 C Click Finish to complete the Presentation wizard.
S 7 – SANsurfer iSCSI/FC Router Manager Wizards Presentation Unmap Wizard The Presentation Unmap wizard provides step-by-step instructions for removing mapping between target LUNs and iSCSI initiators. When the Presentation Unmap wizard launches, the Device Selection dialog box displays, as shown in Figure 7-60. To remove the mapping between a LUN and an iSCSI initiator: 1. Expand the device to expose the LUNs below it. 2. Select the check box next to the mapped LUN, then click Next.
A 7 – SANsurfer iSCSI/FC Router Manager Wizards Figure 7-61 Select the Initiator for the LUN Presentation Dialog Box 3. Select one or more iSCSI initiators that are mapped to the LUN, then click Next. The Confirm Changes dialog box displays, as shown in Figure 7-62. Figure 7-62 Confirm Changes Dialog Box 4. FI0154601-00 C Confirm the LUN mapping changes by clicking Next.
S 7 – SANsurfer iSCSI/FC Router Manager Wizards The Security Check dialog box displays, as shown in Figure 7-63. Figure 7-63 Security Check Dialog Box 5. Enter the appropriate password, then click OK to confirm the unmapping. The LUN Masking Configuration Status dialog box displays, displaying the operation status. 6. Review the status, then click Next. The Finish screen displays, as shown in Figure 7-64. Figure 7-64 Target Unmapping Wizard Finish Dialog Box 7.
A Command Reference The command line interface (CLI) enables you to perform a variety of router management tasks through an Ethernet or serial port connection.
S A – Command Reference Guest Account Guest Account Routers come from the factory with the following account already defined: Account name: Password: guest password This guest account provides access to the router and its configuration. After planning your router management needs, consider changing the password for this account. The guest account is automatically closed after 15 minutes of inactivity. See the password command (page A-20) for information about changing passwords.
A A – Command Reference Working with SAN Router Configurations Save Router Configuration and Persistence Perform the following steps to save the router’s configuration and persistent data. Persistent data consists of LUN mappings, discovered FC targets, and discovered iSCSI initiators. 1. Execute the fru save CLI command to generate a file (iSR-6140_FRU.bin) containing the saved data (see page A-10). This stores the file locally on the router in an FTP directory. 2.
S A – Command Reference Working with SAN Router Configurations Restore Router Configuration and Persistence To restore the router’s configuration and persistent data: 1. Transfer the saved data from a workstation to the router by executing an FTP utility on the workstation. The following example shows an FTP transfer to put previously saved router configuration data on the router: c:\>ftp 172.17.137.102 Connected to 172.17.137.102. 220 (none) FTP server (GNU inetutils 1.4.2) ready. User (172.17.137.
A A – Command Reference Commands Commands The CLI command syntax is as follows: command keyword keyword [value] keyword [value1] [value2] The command is followed by one or more keywords. Consider the following rules and conventions: Commands and keywords are case insensitive. Required keyword values appear in standard font: [value]. Optional values are shown in italics: [value]. Underlined portions of the keyword in the command format indicate the abbreviated form that can be used.
S A – Command Reference Commands Admin Command Opens and closes an administrator session. Any command that changes the router configuration requires that the user be in an Admin session. Only one Admin session can be open on the router at any time. An inactive Admin session will time out after a period of 15 minutes. Authority Admin session Syntax admin start (or begin) end (or stop) cancel Keywords start (or begin) Opens the Admin session. end (or stop) Closes the Admin session.
A A – Command Reference Commands Beacon Command Enables or disables flashing the LEDs. Authority None Syntax beacon on off Keywords on Turns on the router beacon. off Turns off the router becon.
S A – Command Reference Commands Clear Command Removes all entries from the router’s log file or resets the Fibre Channel and iSCSI statistic counters. Authority Admin session Syntax clear [logs or stats] Keywords logs Clears all entries from router’s log file. stats Resets the statistic counters.
A A – Command Reference Commands Date Command Displays or sets the date and time. To set the date and time, you must enter the information in this format: MMDDhhmmCCYY. The new date and time takes effect immediately. Authority Admin session to set the date and time. No authority required to display the current date and time Syntax date [MMDDhhmmCCYY] Keywords [MMDDhhmmCCYY] Specifies the date—this requires an Admin session.
S A – Command Reference Commands FRU Command Saves and restores the router’s configuration. Authority Admin session to restore Syntax fru restore save Keywords restore The fru restore command requires that you first ftp the tar file containing the desired configuration to the router. When you issue this command, the system prompts you to enter the restore level. You can fully restore the router’s configuration (all configuration parameters and LUN mappings) or restore only the LUN mappings.
A A – Command Reference Commands Help Command Displays a list of the commands and their syntax.
S A – Command Reference Commands luns | lunmask | memory ntp | presented_targets | snmp system | targets | vlan | mgmt | stats ] show chap show fc [ ] show initiators [ fc | iscsi ] show initiators_lunmask show iscsi [ ] show isns [ ] show logs [ ] show luninfo show luns show lunmask show memory show mgmt show ntp show presented_targets [ fc | iscsi ] show snmp show stats show system show targets [ fc | iscsi ] show vlan [ ] security target [
A A – Command Reference Commands History Displays a numbered list of the previously entered commands.
S A – Command Reference Commands Image Command Updates the router’s firmware image and cleans up (removes) the image files in the router’s /var/ftp directory. Authority Admin session Syntax image cleanup unpack [file] Keywords cleanup Removes all firmware image files in the router’s /var/ftp directory. These are files transferred by the user when updating the router’s firmware image.
A A – Command Reference Commands Initiator Command Adds, modifies, and removes an initiator in the router’s database. Authority Admin session Syntax initiator add mod remove Keywords add Adds an initiator the router’s database. mod Modifies the settings of an initiator. remove Removes an initiator. Examples The following example shows the initiator add command: QRouter (admin) #> initiator add A list of attributes with formatting and current values will follow.
S A – Command Reference Commands Please select an Initiator from the list above ('q' to quit): 0 A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so. OS Type (0=MS Windows, 1=Linux, 2=Other) [MS Windows ] All attribute values for that have been changed will now be saved.
A A – Command Reference Commands Logout Command Exits the command line interface and returns you to the login prompt.
S A – Command Reference Commands Lunmask Command Maps a target LUN to an initiator, and also removes mappings. It prompts you to pick from a list of targets, LUNs, and initiators. Authority Admin session Syntax lunmask add remove Keywords add Maps a LUN to an initiator. First, you are prompted to select an initiator from a list of initiators. Then you are promoted select a target from a list of targets.
A A – Command Reference Commands 0 20:00:00:20:37:fd:8b:ab:00:00:00:00:fc:b7:3f:fa SEAGATE Please select a LUN to present to the initiator ('q' to quit): 0 All attribute values for that have been changed will now be saved.
S A – Command Reference Commands Password Command Changes the guest and administrator passwords. Authority Admin session Syntax passwd Examples The following example shows the passwd command: QRouter (admin) #> passwd Press 'q' and the ENTER key to abort this command. Select password to change (0=guest, 1=admin) : 1 account OLD password : ****** account NEW password (6-128 chars) : ****** please confirm account NEW password : ****** Password has been changed.
A A – Command Reference Commands Ping Command Verifies the connectivity of each Ethernet port, management, GE1, and GE2. Authority Admin session Syntax ping Examples The following example shows the ping command: QRouter (admin) #> ping A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
S A – Command Reference Commands Quit Command Exits the command line interface and returns you to the login prompt.
A A – Command Reference Commands Reboot Command Restarts the router firmware. Authority Admin session Syntax reboot Examples The following example shows the reboot command: QRouter (admin) #> reboot Are you sure you want to reboot the System (y/n): y System will now be rebooted...
S A – Command Reference Commands Reset Factory Command Restores the router configuration parameters to the factory default values. It deletes all LUN mappings, as well as all persistent data regarding targets, LUNs, and initiators. This command also restores the factory default IP addresses. Authority Admin session Syntax reset factory Keywords factory Restores the router to factory default configuration.
A A – Command Reference Commands Save Command Saves logs and traces. Authority Admin session Syntax save logs traces Keywords logs The save logs command creates a tar file that contains the router’s log data, storing the file in the router’s /var/ftp directory. After the command completes, you must ftp the log’s tar file from the router. traces The save traces command creates a tar file that contains the router’s dump data, storing the tar file in the router’s /var/ftp directory.
S A – Command Reference Commands Set Command Configures general router parameters as well as parameters that are specific to the Fibre Channel, iSCSI, and management ports. Authority Admin session Syntax set chap fc [port_num] iscsi [port_num] isns [port_num] mgmt ntp snmp system vlan Keywords chap Sets the CHAP secrets. fc [port_num] Sets the Fibre Channel port parameters. iscsi [port_num] Sets the iSCSI port parameters. isns [port_num] Set the iSNS parameters.
A A – Command Reference Commands Set CHAP Command Configures general router parameters. Authority Admin session Syntax set chap Examples The following example shows the set chap command: QRouter (admin) #> set chap A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
S A – Command Reference Commands Set FC Command Configures a Fibre Channel port. Authority Admin session Syntax set fc [port_num] Keywords [port_num] The number of the FC port to be configured. Examples The following example shows the set fc command: QRouter (admin) #> set fc A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value.
A A – Command Reference Commands All attribute values for Port 2 that have been changed will now be saved.
S A – Command Reference Commands Set iSCSI Command Configures an iSCSI port. Authority Admin session Syntax set iscsi [port_num] Keywords [port_num] The number of the iSCSI port to be configured. Examples The following example shows the set iscsi command: QRouter (admin) #> set iscsi 1 A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value.
A A – Command Reference Commands IPv6 Window Scaling (0=Enable, 1=Disable) [Enabled ] IPv6 Window Scaling Factor (Min=0, Max=5) [1 ] IPv6 VLAN (0=Enable, 1=Disable) [Disabled ] All attribute values for Port 1 that have been changed will now be saved.
S A – Command Reference Commands Set iSNS Command Configures iSNS parameters for an iSCSI port. Authority Admin session Syntax set isns [port_num] Keywords [port_num] The number of the iSCSI port to be configured for iSNS. Examples The following example shows the set isns command: QRouter (admin) #> set isns 1 A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value.
A A – Command Reference Commands Set Mgmt Command Configures the router’s management port (10/100). Authority Admin session Syntax set mgmt Examples The following example shows the set mgmt command: QRouter (admin) #> set mgmt A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
S A – Command Reference Commands Set NTP Command Configures the NTP parameters. Authority Admin session Syntax set ntp Examples The following example shows the set ntp command: QRouter (admin) #> set ntp A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
A A – Command Reference Commands Set SNMP Command Configures the general simple network management protocol (SNMP) properties, as well as configuring eight trap destinations. Authority Admin session Syntax set snmp trap_destinations Keywords trap_destinations Specifies the setting of the trap destinations. Examples The following example shows the set snmp command for setting the general properties: QRouter (admin) #> set snmp A list of attributes with formatting and current values will follow.
S A – Command Reference Commands Destination enabled (0=Enable, 1=Disable) IP Address [Disabled [0.0.0.0 ] 0 ] 10.0.0.
A A – Command Reference Commands Set System Command Configures the general router parameters. Authority Admin session Syntax set system Examples The following example shows the set system command: QRouter (admin) #> set system A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
S A – Command Reference Commands Set VLAN Command Configures the router’s VLAN parameters. Authority Admin session Syntax set vlan Examples The following example shows the set vlan command: QRouter (admin) #> set vlan A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
A A – Command Reference Commands Show Command Displays router operational information. Authority None Syntax show chap fc [port_num] initiators [fc or iscsi] initiator_lunmask iscsi [port_num] isns [port_num] logs [entries] luninfo luns lunmask mgmt ntp presented_targets [fc or iscsi] snmp stats targets [fc or iscsi] system vlan [port_no] Keywords chap Displays configured chap iSCSI nodes. fc [port_num] Displays Fibre Channel port information.
S A – Command Reference Commands luninfo Displays complete LUN information for a specified target and LUN. luns Displays LUN information and their targets. lunmask Displays LUN mappings. mgmt Displays the router’s management port (10/100) configuration. ntp Displays the router’s network time protocol (NTP) configuration. presented_targets [fc or iscsi] Displays targets presented by the router: FC, iSCSI, or both.
A A – Command Reference Commands Show CHAP Command Displays CHAP configuration for iSCSI nodes. Authority None Syntax show chap Examples The following example shows the show fc command: QRouter (admin) #> show chap The following is a list of iSCSI nodes that have been configured with CHAP 'ENABLED': Type iSCSI Node -------- ------------ Init iqn.1991-05.com.
S A – Command Reference Commands Show FC Command Displays Fibre Channel port information for the specified port. If you do not specify a port, this command displays both ports. Authority None Syntax show fc [port_num] Keywords [port_num] Identifies the number of the FC port to display.
A A – Command Reference Commands Show Initiators Command Displays SCSI initiator information for iSCSI, FC, or both. Authority None Syntax show initiators fc iscsi Keywords fc Specifies the display of Fibre Channel initiators. iscsi Specifies the display of iSCSI initiators. Examples The following example shows the show initiators command: QRouter #> show initiators Initiator Information ----------------------Initiator Name iqn.1991-05.com.
S A – Command Reference Commands Show Initiators LUN Mask Command Displays initiators and the LUNs to which they are mapped. Authority None Syntax show initiators_lunmask Examples The following example shows the show initiators LUN Mask command: QRouter #> show initiators_lunmask Index (WWNN/iSCSI Name) ----- ----------------- 0 iqn.1991-05.com.
A A – Command Reference Commands Show iSCSI Command Displays iSCSI information for the specified port. If the port is not specified, then both ports are displayed. Authority None Syntax show iscsi [port_num] Keywords [port_num] The number of the iSCSI port to be displayed. Examples The following example shows the show iscsi port command: QRouter (admin) #> show iscsi iSCSI Port Information -----------------------iSCSI Port 1 Port Status Enabled Link Status Up iSCSI Base Name iqn.2004-08.com.
S A – Command Reference Commands IPv6 Link Local fe80::2c0:ddff:fe0c:8be2 IPv6 Default Router :: IPv6 Target TCP Port No. 3260 IPv6 Window Scaling Enabled IPv6 Window Scaling Factor 1 IPv6 VLAN Disabled iSCSI Port 2 Port Status Enabled Link Status Up iSCSI Base Name iqn.2004-08.com.qlogic:isr-6140.0608a00471.1 MAC Address 00-c0-dd-0c-8b-e3 IP Address 0.0.0.0 Subnet Mask 0.0.0.0 Gateway IP Address 0.0.0.0 Firmware Revision No. 3.00.02.44 No.
A A – Command Reference Commands Show iSNS Command Displays iSNS configuration information for the specified iSCSI port. If you do not specify the port, this command displays the iSNS configuration information for both iSCSI ports. Authority None Syntax show isns [port_num] Keywords [port_num] The iSCSI port number whose iSNS configuration is to be displayed.
S A – Command Reference Commands Show Logs Command Displays the router event log.
A A – Command Reference Commands Show Luninfo Command Displays complete information for a specified LUN and target.
S A – Command Reference Commands Show LUNs Command Displays LUN information for each target.
A A – Command Reference Commands Show Lunmask Command Displays LUN mappings.
S A – Command Reference Commands Show Mgmt Command Displays the router’s management port (10/100) configuration. Authority None Syntax show mgmt Examples The following example shows the show mgmt command: QRouter (admin) #> show mgmt Management Port Information ----------------------------- A-52 IPv4 Interface Enabled IPv4 Mode Dhcp IPv4 IP Address 172.17.137.129 IPv4 Subnet Mask 255.255.254.0 IPv4 Gateway 172.17.136.
A A – Command Reference Commands Show NTP Command Displays the router’s network time protocol (NTP) configuration.
S A – Command Reference Commands Show Presented Targets Command Displays targets presented by the router: FC, iSCSI, or both. Authority None Syntax show presented_targets fc iscsi Keywords fc Specifies the display of FC presented targets. iscsi Specifies the display of iSCSI presented targets. Examples The following example shows the show presented_targets fc command: QRouter #> show presented_targets fc No Presented Targets found.
A A – Command Reference Commands Name iqn.2000-04.com.qlogic:isr6140:0.50001fe150011150.50001fe150011158 IP 10.3.5.66 CHAP Disabled WWNN 50:00:1f:e1:50:01:11:50 WWPN 50:00:1f:e1:50:01:11:58 Name iqn.2000-04.com.qlogic:isr6140:1.50001fe150011150.50001fe150011158 IP 10.3.5.
S A – Command Reference Commands Show SNMP Command Displays the router’s simple network management protocol (SNMP) and any traps that have been configured. Authority None Syntax show snmp Examples The following example shows the show snmp command: QRouter (admin) #> show snmp SNMP Configuration -----------------Read Community Public Trap Community Private System Location System Contact Authentication traps Disabled System OID 1.3.6.1.4.1.3873.1.
A A – Command Reference Commands Show Stats Command Displays the router statistics: FC and iSCSI.
S A – Command Reference Commands A-58 MAC Xmit Dropped Frames 0 MAC Xmit Jumbo Frames 0 MAC Rcvd Frames 42061498217 MAC Rcvd Byte Count 60362392962831 MAC Rcvd Unknown Control Frames 0 MAC Rcvd Pause Frames 0 MAC Rcvd Control Frames 0 MAC Rcvd Dribbles 0 MAC Rcvd Frame Length Errors 0 MAC Rcvd Jabbers 0 MAC Rcvd Carrier Sense Errors 0 MAC Rcvd Dropped Frames 0 MAC Rcvd CRC Errors 0 MAC Rcvd Encoding Errors 0 MAC Rcvd Length Errors Large 1 MAC Rcvd Small Errors Small 0 MAC
A A – Command Reference Commands MAC Rcvd Unknown Control Frames 0 MAC Rcvd Pause Frames 0 MAC Rcvd Control Frames 0 MAC Rcvd Dribbles 0 MAC Rcvd Frame Length Errors 0 MAC Rcvd Jabbers 0 MAC Rcvd Carrier Sense Errors 0 MAC Rcvd Dropped Frames 0 MAC Rcvd CRC Errors 0 MAC Rcvd Encoding Errors 0 MAC Rcvd Length Errors Large 0 MAC Rcvd Small Errors Small 0 MAC Rcvd Multicast Frames 94 MAC Rcvd Broadcast Frames 91 iSCSI Shared Statistics ----------------------- FI0154601-00 C PDUs
S A – Command Reference Commands A-60 IP Fragment Rcvd Out of Order 0 IP Datagram Reassembly Timeouts 0 TCP Xmit Segment Count 54392134284 TCP Xmit Byte Count 57389353022514 TCP Rcvd Segment Count 42061430681 TCP Rcvd Byte Count 57418079800284 TCP Persist Timer Expirations 0 TCP Rxmit Timer Expired 116 TCP Rcvd Duplicate Acks 986657165 TCP Rcvd Pure Acks 816265831 TCP Xmit Delayed Acks 3584507 TCP Rcvd Pure Acks 177811024 TCP Rcvd Segment Errors 0 TCP Rcvd Segment Out of Order
A A – Command Reference Commands Show System Command Displays router product information including the serial number, software version, hardware version, configuration, and temperature. Authority None Syntax show system Examples The following example shows the show system command: QRouter #> show system System Information -------------------Product Name iSR-6140 Symbolic Name FI0154601-00 C Serial Number 0608A00471 HW Version 5 (IPv6 Supported) SW Version 2.4.2.0rc2 No. of FC Ports 2 No.
S A – Command Reference Commands Show Targets Command Displays targets discovered by the router: FC, iSCSI, or both. Authority None Syntax show targets fc scsi Keywords fc Specifies the display of FC targets. iscsi Specifies the display of iSCSI targets.
A A – Command Reference Commands The following example shows the show targets iscsi command: QRouter #> show targets iscsi No Targets found.
S A – Command Reference Commands Show VLAN Command Displays the router’s VLAN configuration. Authority None Syntax show vlan [port_num] Keywords [port_num] Examples The iSCSI port number whose VLAN configuration is to be displayed.
A A – Command Reference Commands Target Command Removes targets from the router’s database. This command is typically used to remove targets from the database that are no longer connected to the router. The target add command is not currently supported. Authority Admin session Syntax target add rm Keywords add Not supported rm Remove a target from the router’s target database.
S A – Command Reference Commands TargetMap Command The targetmap command is not currently supported. Targets are automatically presented.
A A – Command Reference Commands The following example shows the targetmap rm (remove) command: QRouter (admin) #> targetmap rm Index (WWNN,WWPN/iSCSI Name) ----- ---------------------- 0 20:00:00:20:37:fd:8b:ab,22:00:00:20:37:fd:8b:ab 1 20:00:00:20:37:fd:8a:b0,22:00:00:20:37:fd:8a:b0 2 20:00:00:20:37:fd:9c:f7,22:00:00:20:37:fd:9c:f7 3 20:00:00:20:37:fd:8d:00,22:00:00:20:37:fd:8d:00 Please select a target from the list above ('q' to quit): 0 Failed saving Mapping Information.
S A – Command Reference Commands Traceroute Command Prints the route a network packet takes to the reach the destination specified by the user. Authority Admin session Syntax traceroute Examples Traceroute command example: A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
B Configuring CHAP CHAP Definition In challenge handshake authentication protocol (CHAP), the authentication agent sends the client program a random value that is used only once and an ID value. Both the sender and peer share a predefined secret. The peer concatenates the random value, the ID, and the secret; it calculates a one-way hash using MD5 (Message-Digest algorithm 5).
S B – Configuring CHAP Configuring CHAP Using CLI 2. 3. Use the initiator add command to add the initiator that is about to do discovery: a. Enable the CHAP for this initiator. b. Create a secret (for example, secret_initiator). c. Use the set chap command to update the CHAP settings of the initiator. Go to the Microsoft iSCSI (MS) Initiator and perform the following steps: a. Click General. b. Click Secret (in the middle of the screen).
A B – Configuring CHAP Configuring CHAP Using CLI 6. Type the address of the iSCSI port of the router. 7. Click Advanced. 8. Select Chap Login Information. 9. In Target Secret, type the secret (secret_initiator) you created in Step 2. 10. Click OK. 11. Click OK. The initiator should complete discovery. CLI—Normal Session—Bi-directional CHAP To configure a bi-directional CHAP used during a normal session: 1. 2. 3. On the router a.
B – Configuring CHAP Configuring CHAP Using the GUI S CLI—Normal Session—Uni-directional CHAP To configure single-direction CHAP to be used during a normal session: 1. Do not enable CHAP on the presented target. 2. Use the initiator add command: a. Add the initiator that is about to do a normal login. b. Enable the CHAP for this initiator. c. Create a secret (for example, secret_initiator). d. Use the set chap command to update the CHAP settings of the initiator. 3. Go to the MS Initiator. 4.
A B – Configuring CHAP Configuring CHAP Using the GUI 7. Type the IQN name string. 8. Select Enable CHAP. 9. Create a CHAP secret (for example, secret_initiator). 10. Go to the MS Initiator and perform the following steps: a. Click General. b. Click Secret (in the middle of the screen). c. If this is the first time you are setting secrets, reset all secrets. d. Type the CHAP secret (secret_port) that you created in Step 5. 11. Click Discovery. 12. Click Add. 13.
S B – Configuring CHAP Configuring CHAP Using the GUI c. Enter the address of the iSCSI port of the bridge. d. Click Advanced. e. Click Chap Login Information. f. Type the secret (secret_initiator) you created in Step 5 into Target Secret. 7. Click OK. 8. Click OK. The initiator completes discovery. GUI—Normal Session—Bi-directional CHAP To program bi-directional CHAP during a normal session: B-6 1. On the bridge, enable CHAP for the iSCSI presented target. 2.
A B – Configuring CHAP Configuring CHAP Using the GUI 15. Select Chap Login Information. 16. Type the secret (secret_initiator) that you created in Step 9 into Target Secret. 17. Select Mutual Authentication. 18. Click OK. 19. Click OK. The initiator completes normal login. GUI—Normal Session—Uni-directional CHAP To program single-direction CHAP during a normal session: 1. Do not enable CHAP on the iSCSI presented target. 2.
B – Configuring CHAP Configuring CHAP Using the GUI S Notes B-8 FI0154601-00 C
C Log Messages Log Data The router maintains a message log you can display and retrieve either through the command line interface (CLI) or the SANsurfer Router Manager. The message log is persistent in that it is maintained across router power cycles and reboots. The three log message categories are: Informational Error Fatal The following sections describe the log message categories.
S C – Log Messages Informational Log Messages Table C-1. Application Modules—Informational Log Messages (Continued) ID Log Message No.
A C – Log Messages Informational Log Messages Table C-2. SCSI Driver—Informational Log Messages ID Log Message 86874 #%d: QLIsrDecodeMailbox: Link up 331 Restart iSCSI processor (RISC) 333 EEPROM updated, restart iSCSI processor (RISC) 858 Link up reported by iSCSI processor for GE1 or GE 2 No. 858 Fibre Channel Driver The following log messages are common to both Fibre Channel ports: 1 (FC1) and 2 (FC2). The messages are listed in Table C-3 and described following the table.
S C – Log Messages Error Log Messages 308 Fibre Channel link up occurred. Event status is reported, as is the RunTimeMode (0 = loop, 1 = point-to-point). 309 A RSCN was received. Event status is reported, as is the RSCN information. 313 Fibre Channel port update. Event status is reported, as is the contents of the FC processor’s mailbox 1, 2, and 3 registers. Error Log Messages The following sections list and describe the error log messages by reporting module.
A C – Log Messages Error Log Messages Table C-4. Application Module—Error Log Messages (Continued) ID FI0154601-00 C Log Message No.
S C – Log Messages Error Log Messages Table C-4. Application Module—Error Log Messages (Continued) ID C-6 Log Message No. 42404 QLIS_ProcessStartTrb: [%d] CmdSN %ld is out of range (%ld - %ld), Cdb[0] 0x%02X, DataXferLen 0x%x. 1444 41234 QLIS_LoginPduContinue: Operation failed. Initiator 0x%x, TPB status 0x%x 274 41238 QLKV_ValidateLoginTransitCsgNsgVersion failed (status 0x%x) 278 41257 QLIS_LoginPduContinue: Invalid initiator name.
A C – Log Messages Error Log Messages 136 Process control block status indicates that a PCI error occurred during a target operation 146 Process control block status indicates that a DMA error occurred during an initiator operation 147 Process control block status indicates that a transport error (protocol) occurred during an initiator operation 151 Process control block status indicates that a data overrun error occurred during an initiator operation 548 Failed to allocate an object for Set Port
S C – Log Messages Error Log Messages C-8 1035 Login attempted using Fibre Channel VP index that has not been configured. Operation attempted on an unconfigured VP. 1042 Attempting login but Fibre Channel connection cannot be opened. 1064 Attempting logout of device for which there is no active path (WWPN not found). 1067 Logout attempted using Fibre Channel VP index that has not been configured. Operation attempted on an unconfigured VP.
A C – Log Messages Error Log Messages 324 iSCSI Login PDU was received with an invalid TSIH value. The TSIH is invalid because there is no session with that TSIH value. This would occur if the iSCSI initiator attempting the login failed to used the TSIH value provided in the target login response PDU (router is target) in subsequent login PDUs. 1688 Event notification; iSCSI driver encountered a fatal error. 1689 Event notification; an IOCTL request was received to unload the iSCSI driver.
S C – Log Messages Error Log Messages 262 The iSCSI processor failed firmware initialization. 328 The iSCSI processor failed the internal loopback test. 329 The iSCSI processor failed the external loopback test. 513 The iSCSI processor could not connect with the iSCSI name server (iSNS). 849 The iSCSI processor reported that the iSCSI port NVRAM contains invalid data (checksum error). 859 The iSCSI processor reported a link down condition.
A C – Log Messages Error Log Messages Table C-6. Fibre Channel Driver—Error Log Messages (Continued) ID FI0154601-00 C Log Messages No.
S C – Log Messages Error Log Messages 452 The FC processor is unable to log into the FC fabric name server. 533 The driver’s host (initiator) database is full. 545 The driver’s target database is full. 560 The driver’s host (initiator) database is full. Maximum host database is 64. 582 The drivers host (initiator) database is full. User Modules The user modules provide the error log messages listed in Table C-7 and described following the table. Table C-7.
A C – Log Messages Error Log Messages Table C-7. User Modules—Error Log Messages (Continued) ID FI0154601-00 C Log Message No.
S C – Log Messages Error Log Messages 20 Failed memory allocation for Get Target List API. 21 Failed memory allocation for Get LUN List API. 22 Failed memory allocation for Get Presented Targets List API. 23 Failed memory allocation for Get LUN Mask API. 24 Failed memory allocation for Initiator API. 25 Failed memory allocation for Target Device API. 32 Failed memory allocation for FC Target API. 33 Failed memory allocation for System Status API.
A C – Log Messages Fatal Log Messages Fatal Log Messages The following sections list and describe the fatal log messages by reporting module. iSCSI Driver The following fatal log messages are common to both iSCSI ports, 1 (GE1) and 2 (GE2). They are listed in Table C-9 and described following the table. Log messages beginning with #0 denote iSCSI port 1 (GE1). Log messages beginning with #1 denote iSCSI port 2 (GE2). Table C-9. iSCSI Driver—Fatal Log Messages ID FI0154601-00 C Log Message No.
S C – Log Messages Fatal Log Messages Table C-9. iSCSI Driver—Fatal Log Messages (Continued) C-16 ID Log Message No. 70501 #%d: QLProcessResponseQueue: Invalid entry type in response queue %x 869 70502 #%d: QLProcessResponseQueue: Invalid handle %x EntryType %x 870 70524 #%d: QLProcessAen: Invalid event %x 892 70544 #%d: QLRebootTimer: Reboot failed! 912 70563 #%d: QLReadyTimer: Adapter missed heartbeat for 0x%x seconds.
A C – Log Messages Fatal Log Messages 867 Response queue invalid handle for ET pass-through. 869 Response queue invalid entry type. 870 Response queue invalid handle for specified entry type. 892 Asynchronous event for unknown event type. 912 Reboot timer failed. 931 iSCSI driver missed iSCSI processor heartbeat. iSCSI processor rebooted. 932 iSCSI processor failed to complete operation before timeout. 977 iSCSI processor system error restart. 978 iSCSI processor reboot failed.
S C – Log Messages Fatal Log Messages Table C-10. Fibre Channel Driver—Fatal Log Messages (Continued) C-18 ID Log Message No.
A C – Log Messages Fatal Log Messages 400 FC processor being restarted. System The system modules provide the error log messages listed in Table C-11 and described following the table. Table C-11. System—Fatal Log Messages FI0154601-00 C ID Log Message No.
C – Log Messages Fatal Log Messages S Notes C-20 FI0154601-00 C
D Simple Network Management Protocol (SNMP) Introduction Simple network management protocol (SNMP) provides monitoring and trap functions for managing the router through third-party applications that support SNMP. The router firmware supports SNMP versions 1 and 2 and a QLogic management information base (MIB) (see page D-3). You may format traps using SNMP version 1 or 2.
S D – Simple Network Management Protocol (SNMP) Introduction Table D-1. SNMP Properties (Continued) Parameter Description System contact Specifies the name of the person to be contacted to respond to trap events. The name can be up to 64 characters excluding the number sign (#), semicolon (;), and comma (,). The default is undefined. Authentication traps Enables or disables the generation of authentication traps in response to authentication failures. The default is disabled.
A D – Simple Network Management Protocol (SNMP) Management Information Base (MIB) Management Information Base (MIB) The following sections describe the QLogic management information base (MIB).
S D – Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrNoOfGbEPorts Syntax Unsigned32 Access Read-only Description The number of gigabit Ethernet ports on the system. qsrAgentVersion Syntax SnmpAdminString Access Read only Description The version number of the agent software on the system. Network Port Table The network port table contains a list of network ports that are operational on the router.
A D – Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrGateway InetAddress qsrMacAddress MacAddress qsrNwLinkStatus QsrLinkStatus qsrNwLinkRate QsrLinkRate qsrNwPortRole Syntax QsrPortRole Access Not accessible Description The operational role of this port: management port or iSCSI port. qsrNwPortIndex Syntax Unsigned32 Access Not accessible Description A positive integer indexing each network port in a given role.
D – Simple Network Management Protocol (SNMP) Management Information Base (MIB) S qsrNetMask Syntax InetAddress Access Read only Description The subnet mask for this port. qsrGateway Syntax InetAddress Access Read only Description The gateway for this port. qsrMacAddress Syntax IMacAddress Access Read only Description The MAC address for this port. qstNwLinkStatus Syntax QsrLinkStatus Access Read only Description The operational link status for this port.
A D – Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrFcPortEntry Syntax QsrFcPortEntry Access Not accessible Description Each entry (row) contains information about a specific FC port.
D – Simple Network Management Protocol (SNMP) Management Information Base (MIB) S qsrFcPortWwn Syntax PhysAddress Access Read only Description The world wide name for this port. qsrFcPortId Syntax PhysAddress Access Read only Description The interface's 24-bit FC address identifier. qsrFcPortType Syntax Unsigned32 Access Read only Description The type of FC port, as indicated by the use of the appropriate value assigned by IANA.
A D – Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrSensorEntry Syntax QsrSensorEntry Access Not accessible Description Each entry (row) corresponds to a single sensor.
D – Simple Network Management Protocol (SNMP) Management Information Base (MIB) S qsrSensorValue Syntax Integer32 Access Read only Description The current value of the sensor. qsrUpperThreshold Syntax Integer32 Access Read only Description The upper-level threshold for this sensor. qsrLowerThreshold Syntax Integer32 Access Read only Description The lower-level threshold for this sensor.
A D – Simple Network Management Protocol (SNMP) Notifications Notifications The router provides the following six notification types: Agent Start Up Notification (see page D-12) Agent Shut Down Notification (see page D-12) Network Port Down Notification (see page D-12) Fibre Channel Port Down Notification (see page D-12) Sensor Notification (see page D-13) Generic Notification (see page D-13) The following sections describe these notifications and objects they use.
D – Simple Network Management Protocol (SNMP) Notifications S Agent Start Up Notification The agent startup notification indicates that the agent on the router has started running. qsrAgentStartup uses the following object: qsrEventTimeStamp Agent Shut Down Notification The agent shut down notification indicates that the agent on the router is shutting down.
A D – Simple Network Management Protocol (SNMP) Notifications Sensor Notification The sensor notification indicates that the state for the specified sensor is not normal. When the sensor returns to the normal state, this event is sent with the qsrEventSeverity object set to clear. qsrSensorNotification uses the following objects: qsrSensorValue qsrSensorState qsrEventTimeStamp qsrEventSeverity Generic Notification The generic notification reports events other than the defined event types.
D – Simple Network Management Protocol (SNMP) Notifications S Notes D-14 FI0154601-00 C
Index A AC power 4-9 Account, guest A-2 Action menu 7-6 Admin command A-6 Advanced configuration FC port 7-21 iSCSI port 7-28 Agent notification D-12 Application module log messages C-1, C-4 Audience 1-1 Auto connect, enable 7-4 B Base name, iSCSI port 7-25 Beacon 7-7 Beacon command A-7 Bi-directional CHAP configuration B-1, B-3, B-4, B-6 Blink patterns heartbeat 5-3 IP address conflict 5-4 LED 5-3 over-temperature 5-4 system error 5-3 Boot image, selecting 2-4 Broadcast enable 7-4 interval 7-4 Browser loc
S SANbox 6140 Intelligent Storage Router User’s Guide Commands admin A-6 beacon A-7 clear A-8 data A-9 FRU A-10 help A-11 history A-13 image A-14 initiator A-15 logout A-17 lunmask A-18 password A-20 ping A-21 quit A-22 reboot A-23 reset factory A-24 save A-25 set A-26 set CHAP A-27 set FC A-28 set iSCSI A-30 set iSNS A-32 set mgmt A-33 set NTP A-34 set SNMP A-35 set system A-37 set VLAN A-38 show A-39 show FC A-41, A-42 show initiators A-43 show initiators LUN mask A-44 show iSCSI A-45 show iSNS A-47 sho
A Ethernet, iSCSI/gigabit Ethernet port LEDs 2-7 F Factory resetting factory command A-24 restoring defaults 2-4 Failure, recover from 3-8 Fatal log messages, system errors C-15 FCC Class A statement 1-3 Fibre Channel devices, distance between 3-2, 3-3 driver messages C-3, C-10, C-17 MIB port table D-6 port count 7-13 port information 7-20 port LEDs 2-5 set FC command A-28 show FC command A-41, A-42 targets, discovered 7-34 File menu 7-3 Firmware, installing 4-11 FRU command A-10 FRUs 1-5 FTP 3-8 FW Update
S SANbox 6140 Intelligent Storage Router User’s Guide iSCSI driver messages C-2, C-9, C-15 initiators, adding 7-52 initiators, discovered 7-30 port count 7-13 port information 7-24 port LED 2-7 ports, configuring 7-45 presented targets 7-40 set iSCSI command A-30 targets, presented 7-36 iSCSI port advanced configuration 7-28 IPv4 address 7-25 IPv6 address 7-26 network settings 7-25 statistics 7-30 iSNS enabling 7-27 set iSNS command A-32 show iSNS command A-47 J Jumbo frame 7-29 L Laser safety informati
A Messages application module C-1, C-4 error log C-4 fatal C-15 Fibre Channel driver C-3, C-10, C-17 informational C-1 iSCSI driver C-2, C-9, C-15 log C-1 system C-14, C-19 user modules C-12 MIB D-3 network port D-4 port table D-8 system information D-3 Modes, operation 7-13 Mounting the router 4-4 N Network port, MIB D-4 settings, iSCSI port 7-25 Notification agent shut down D-12 agent start up D-12 generic D-13 sensor D-13 SNMP D-11 NTP 3-8 server information 7-16 set NTP command A-34 show NTP command A-
SANbox 6140 Intelligent Storage Router User’s Guide Requirements browser 4-2 power 4-2 site 4-1 workstation 4-1 Reset factory command A-24 Restoring factory defaults 2-4 router configuration and persistent data A-4 Router configuring 4-9 icons 7-10 mounting 4-4 recovering 5-5 removing 6-2 replacing 6-2 resetting 2-3 Router management 3-8 S Safety 1-2 SANbox 6140 router connect to 7-6 device access to 3-2 devices attached to 3-1 disconnect from 7-7 hardware version 7-13 illustration 2-1 installing 4-3 IQN
A SNMP 3-8, D-1 configuration 7-18 management 7-18 notifications D-11 properties D-1 set SNMP command A-35 show SNMP command A-56 trap configuration D-2 trap receivers 7-19 Software router 3-7 version 7-13 Statements, communication 1-2 Statistics iSCSI port 7-30 show stats command A-57 Stats command A-57 Status icons 7-9 Symbolic name 7-13 System error blink patterns 5-3 fault LED 2-2 messages C-14, C-19 MIB D-3 OID 7-18 set system command A-37 tree 7-8 tree window 7-8 T Target command A-65 iSCSI presented
SANbox 6140 Intelligent Storage Router User’s Guide S Workstation configuring 4-5 connecting to router 4-5 IP address 4-6 requirements 4-1 serial port 4-6 Index-8 FI0154601-00 C
