0 Simplify SANbox 5602 Fibre Channel Switch Installation Guide Firmware Version 4.
0 SANbox 5602 Fibre Channel Switch Installation Guide Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for illustrative purposes only.
Table of Contents Section 1 Introduction 1.1 1.2 1.3 1.4 1.5 1.6 1.6.1 1.6.2 Intended Audience ............................................................................................. 1-1 Related Materials ............................................................................................... 1-2 Safety Notices .................................................................................................... 1-3 Sicherheitshinweise...........................................................
SANbox 5602 Fibre Channel Switch Installation Guide Section 2 0 General Description 2.1 2.1.1 2.1.1.1 2.1.1.2 2.1.2 2.1.2.1 2.1.2.2 2.1.2.3 2.2 2.2.1 2.2.1.1 2.2.1.2 2.2.2 2.2.3 2.3 2.4 2.5 2.6 2.6.1 2.6.2 2.6.3 2.6.4 2.6.5 2.6.6 Chassis Controls and LEDs ............................................................................... 2-2 Maintenance Button................................................................................... 2-2 Resetting a Switch ..........................................
0 SANbox 5602 Fibre Channel Switch Installation Guide 3.5 3.5.1 3.5.2 3.5.3 3.5.4 3.5.4.1 3.5.4.2 3.5.4.3 3.6 3.6.1 3.6.2 3.7 Multiple Chassis Fabrics .................................................................................... 3-6 Optimizing Device Performance ................................................................ 3-7 Domain ID, Principal Priority, and Domain ID Lock ................................... 3-8 Stacking .......................................................................
SANbox 5602 Fibre Channel Switch Installation Guide 0 Section 5 Diagnostics/Troubleshooting 5.1 5.1.1 5.1.2 5.2 5.2.1 5.2.1.1 5.2.1.2 5.2.1.3 5.2.1.4 5.2.2 5.2.2.1 5.2.2.2 5.3 5.4 5.4.1 5.4.2 5.4.3 5.4.4 5.4.5 5.4.6 5.4.7 5.4.8 5.4.9 Chassis Diagnostics ........................................................................................... 5-1 Input Power LED Is Extinguished .............................................................. 5-2 System Fault LED Is Illuminated ..........................
0 SANbox 5602 Fibre Channel Switch Installation Guide Appendix B Command Line Interface B.1 B.2 B.3 B.3.1 B.3.2 B.4 59096-00 A Logging On to a Switch ......................................................................................B-1 User Accounts ....................................................................................................B-2 Working with Switch Configurations ...................................................................B-2 Modifying a Configuration...................
0 SANbox 5602 Fibre Channel Switch Installation Guide Whoami Command..................................................................................B-98 Zone Command.......................................................................................B-99 Zoneset Command ................................................................................B-103 Zoning Command ..................................................................................
0 SANbox 5602 Fibre Channel Switch Installation Guide Tables Table 2-1 3-1 3-2 4-1 B-1 B-2 B-3 B-4 B-5 B-6 B-7 B-8 B-9 B-10 B-11 B-12 B-13 B-14 B-15 B-16 B-17 Page Serial Port Pin Identification ........................................................................................... 2-9 Zoning Database Limits ................................................................................................. 3-2 Port-to-Port Latency ........................................................................
SANbox 5602 Fibre Channel Switch Installation Guide 0 Notes Page x 59096-00 A
Section 1 Introduction This manual describes the features and installation of the SANbox® 5602 Fibre Channel switch, firmware version 4.2. This manual is organized as follows: Section 1 describes the intended audience, related materials, safety notices, communications statements, laser safety information, electrostatic discharge sensitivity precautions, accessible parts, general program license, and technical support. Section 2 is an overview of the switch.
0 1 – Introduction Related Materials 1.2 Related Materials The following manuals and materials are referenced in the text and/or provide additional information. SANbox 5602 Switch Management User’s Guide, publication number 59097-00. QLogic Switch Interoperability Guide v3.0. This PDF document can be downloaded at http://www.qlogic.com/interopguide/info.asp#inter. Fibre Channel-Arbitrated Loop (FC-AL-2) Rev. 6.8. Fibre Channel-10-bit Interface Rev. 2.3.
0 1 – Introduction Safety Notices 1.3 Safety Notices A Warning notice indicates the presence of a hazard that has the potential of causing personal injury. 4-3, 4-18, 6-1 A Caution notice indicates the presence of a hazard that has the potential of causing damage to the equipment. 4-4, 5-14, 6-2 1.4 Sicherheitshinweise Ein Warnhinweis weist auf das Vorhandensein einer Gefahr hin, die möglicherweise Verletzungen zur Folge hat.
0 1 – Introduction Communications Statements 1.6 Communications Statements The following statements apply to this product. The statements for other products intended for use with this product appear in their accompanying manuals. 1.6.1 Federal Communications Commission (FCC) Class A Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
0 1 – Introduction Communications Statements 1.6.3 Avis de conformité aux normes du ministère des Communications du Canada Cet équipement ne dépasse pas les limites de Classe A d'émission de bruits radioélectriques por les appareils numériques, telles que prescrites par le Réglement sur le brouillage radioélectrique établi par le ministère des Communications du Canada.
1 – Introduction Laser Safety Information 0 1.6.5 VCCI Class A Statement This is a Class A product based on the standard of the Voluntary Control Council For Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. 1.
0 1 – Introduction Accessible Parts 1.9 Accessible Parts The Field Replaceable Units (FRUs) for the SANbox 5602 switch are the following: Power supplies Small Form-Factor Pluggable (SFP) optical transceivers XPAK optical transceivers 1.10 Pièces Accessibles Les pièces remplaçables, Field Replaceable Units (FRU), du commutateur SANbox 5602 Fibre Channel Switch sont les suivantes: Alimentations de courant Interfaces aux media d’interconnexion appelés SFP transceivers.
1 – Introduction General Public License 0 1.12 General Public License QLogic® Fibre Channel switches are powered by the Linux operating system. A machine-readable copy of the Linux source code is available upon written request to the following address. A nominal fee will be charged for reproduction, shipping, and handling costs in accordance with the General Public License.
0 1 – Introduction General Public License We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software.
1 – Introduction General Public License 0 modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a. You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. b.
0 1 – Introduction General Public License b. Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c.
1 – Introduction General Public License 0 rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 8. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License.
0 1 – Introduction General Public License License, you may choose any version ever published by the Free Software Foundation. 12. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this.
0 1 – Introduction General Public License one line to give the program's name and an idea of what it does. Copyright (C) yyyy name of author This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
0 1 – Introduction Technical Support 1.13 Technical Support Customers should contact their authorized maintenance provider for technical support of their QLogic switch products. QLogic-direct customers may contact QLogic Technical Support; others will be redirected to their authorized maintenance provider. Visit the QLogic support Web site listed in Contact Information for the latest firmware and software updates. 1.13.
1 – Introduction Technical Support 0 Notes 1-16 59096-00 A
Section 2 General Description This section describes the features and capabilities of the SANbox 5602 Fibre Channel switch. The following topics are described: Chassis Controls and LEDs Fibre Channel Ports Ethernet Port Serial Port Power Supplies and Fans Switch Management Fabrics are managed with the SANsurfer Switch Manager™ switch management application (version 4.02) and the Command Line Interface (CLI).
0 2 – General Description Chassis Controls and LEDs 2.1 Chassis Controls and LEDs The Maintenance button shown in Figure 2-2 is the only chassis control and is used to reset a switch or to recover a disabled switch. The chassis LEDs provide information about the switch’s operational status. These LEDS include the Input Power LED, Heartbeat LED, and the System Fault LED. To apply power to the switch, plug the power cord into the switch AC power receptacle and into a 110 or 230 VAC power source.
0 2 – General Description Chassis Controls and LEDs 2.1.1.2 Placing the Switch in Maintenance Mode To place the switch in maintenance mode, do the following: 1. Isolate the switch from the fabric. 2. Press and hold the Maintenance button with a pointed tool. When the Heartbeat LED alone is illuminated, release the button. 3. After a few seconds, the POST begins illuminating all chassis LEDs. 4. When the POST is complete, the chassis LEDs extinguish leaving only the Heartbeat LED illuminated.
2 – General Description Chassis Controls and LEDs 0 2.1.2.1 Input Power LED (Green) The Input Power LED indicates the voltage status at the switch logic circuitry. During normal operation, this LED illuminates to indicate that the switch logic circuitry is receiving the proper DC voltages. When the switch is in maintenance mode, this LED is extinguished. 2.1.2.2 Heartbeat LED (Green) The Heartbeat LED indicates the status of the internal switch processor and the results of the POST.
0 2 – General Description Fibre Channel Ports 2.2 Fibre Channel Ports The SANbox 5602 switch has 16 Fibre Channel 1-Gbps/2-Gbps ports and 4 Fibre Channel 10-Gbps ports. Ports are numbered 0–19 as shown in Figure 2-4. Each of the 1-Gbps/2-Gbps ports is served by a Small Form-Factor Pluggable (SFP) optical transceiver and is capable of 1-Gbps or 2-Gbps transmission, or with optional licensing, 4-Gbps. SFPs are hot-pluggable.
0 2 – General Description Fibre Channel Ports 2.2.1 Port LEDs Each port has its own Logged-In LED (L) and Activity LED (A) as shown in Figure 2-5. Logged-In LED (Green) Activity LED (Green) Logged-In LED (Green) Activity LED (Green) 16 A L 6 A L 7 A L 8 A L 9 A L 10 A L 11 A L 12 A L 13 A 1-Gbps/2-Gbps Ports L 14 A L 15 L L A A A 17 L L A A 10-Gbps Ports Figure 2-5. Port LEDs 2.2.1.
0 2 – General Description Fibre Channel Ports 2.2.2 Transceivers The SANbox 5602 switch supports SFP optical transceivers for the 1-Gbps/2-Gbps ports and XPAK optical transceivers for the 10-Gbps ports. A transceiver converts electrical signals to and from optical laser signals to transmit and receive data. Duplex fiber optic cables plug into the transceivers which then connect to the devices.
0 2 – General Description Ethernet Port 2.3 Ethernet Port The Ethernet port shown in Figure 2-6 is an RJ-45 connector that provides a connection to a management workstation through a 10/100 Base-T Ethernet cable. A management workstation can be a Windows®, Solaris™, or a Linux® workstation that is used to configure and manage the switch fabric. You can manage the switch over an Ethernet connection using SANsurfer Switch Manager, the Command Line Interface (CLI), or SNMP.
0 2 – General Description Serial Port 2.4 Serial Port The SANbox 5602 switch is equipped with an RS-232 serial port for maintenance purposes. The serial port location is shown in Figure 2-7. You can manage the switch through the serial port using the CLI. Serial Port Figure 2-7. Serial Port and Pin Identification The serial port connector requires a null-modem F/F DB9 cable. The pins on the switch RS-232 connector are shown in Figure 2-7 and identified in Table 2-1.
0 2 – General Description Power Supplies and Fans 2.5 Power Supplies and Fans The power supplies convert standard 110 or 230 VAC to DC voltages for the various switch circuits. Each power supply has an AC power receptacle and two status LEDs as shown in Figure 2-8: The Power Supply Status LED (green) illuminates to indicate that the power supply is receiving AC voltage and producing the proper DC voltages.
0 2 – General Description Switch Management 2.6 Switch Management The switch supports the following management tools: SANsurfer Switch Manager SANsurfer Switch Manager Web Applet Command Line Interface SANsurfer Switch Manager Application Programming Interface Simple Network Management Protocol File Transfer Protocol 2.6.1 SANsurfer Switch Manager SANsurfer Switch Manager is a workstation-based Java® application that provides a graphical user interface for fabric management.
0 2 – General Description Switch Management 2.6.3 Command Line Interface The command line interface (CLI) provides monitoring and configuration functions by which the administrator can manage the fabric and its switches. The CLI is available over an Ethernet connection or a serial connection. Refer to Appendix B Command Line Interface for more information. 2.6.
Section 3 Planning Consider the following when planning a fabric: Devices Device Access Performance Port Licensing Multiple Chassis Fabrics Fabric Security Fabric Management 3.1 Devices When planning a fabric, consider the number of public devices and the anticipated demand. This will determine the number of ports that are needed and in turn the number of switches. Consider how many and what types of switches are needed.
0 3 – Planning Device Access 3.2 Device Access Consider device access needs within the fabric. Access is controlled by the use of zones and zone sets. Some zoning strategies include the following: Group devices by operating system. Separate devices that have no need to communicate with other devices in the fabric or have classified data. Separate devices into department, administrative, or other functional group. Reserve a path and its bandwidth from one port to another.
0 3 – Planning Device Access 3.2.1 Soft Zones Soft zoning divides the fabric for purposes of controlling device discovery. Devices in the same soft zone automatically discover and communicate freely with all other members of the same zone. The soft zone boundary is not secure; traffic across soft zones can occur if addressed correctly. The following rules apply to soft zones: Soft zones that include members from multiple switches need not include the ports of the inter-switch links.
0 3 – Planning Performance 3.3 Performance The SANbox 5602 switch supports class 2 and class 3 Fibre Channel service at transmission rates of 1-, 2-, 4-, or 10-Gbps with a maximum frame size of 2148 bytes. A 1-Gbps/2-Gbps port adapts its transmission speed to match that of the device to which it is connected prior to login when the connected device powers up. 10-Gbps ports transmit at 10-Gbps. Related performance characteristics include the following: Distance Bandwidth Latency 3.3.
0 3 – Planning Performance You can configure recipient and donor ports using the SANsurfer Switch Manager application or the Set Config command. Refer to “Set Config Command” on page B-39 for more information. 3.3.2 Bandwidth Bandwidth is a measure of the volume of data that can be transmitted at a given transmission rate. A 1-Gbps/2-Gbps port can transmit or receive at nominal rates of 1-, 2-, or 4-Gbps depending on the device to which it is connected.
0 3 – Planning Port Licensing 3.4 Port Licensing The SANbox 5602 switch can come from the factory as an 8-, 12-, 16-, or 20-port switch, enabling ports 0–7, 0–11, 0–15, or 0–19 respectively. Ports 16–19 are 10-Gbps ports. You can upgrade the SANbox 5602 switch to enable additional ports up to the 20-port maximum. You can also upgrade transmission capabilities for ports 0–15 to include 4-Gbps.
0 3 – Planning Multiple Chassis Fabrics 3.5.1 Optimizing Device Performance When choosing a topology for a multiple chassis fabric, you should also consider the locality of your server and storage devices and the performance requirements of your application. Storage applications such as video distribution, medical record storage/retrieval or real-time data acquisition can have specific latency or bandwidth requirements. The SANbox 5602 switch provides the lowest latency of any product in its class.
0 3 – Planning Multiple Chassis Fabrics 3.5.2 Domain ID, Principal Priority, and Domain ID Lock The following switch configuration settings affect multiple chassis fabrics: Domain ID Principal priority Domain ID lock The domain ID is a unique number from 1–239 that identifies each switch in a fabric. The principal priority is a number (1–255) that determines the principal switch which manages domain ID assignments for the fabric.
0 3 – Planning Multiple Chassis Fabrics 3.5.3 Stacking You can connect up to four 20-port SANbox 5602 switches together through the 10-Gbps ports, thus preserving the user ports for devices. This is called stacking. The following 2-, 3-, and 4-switch stacking configurations are recommended for best performance and redundancy. Each 10-Gbps port contributes 1 GB of bandwidth between chassis with one chassis hop between any two ports.
0 3 – Planning Multiple Chassis Fabrics A four-switch stack uses three 3-inch and three 9-inch XPAK switch stacking cables as shown in Figure 3-3. 64 1-Gbps/2-Gbps ports are available for devices.
0 3 – Planning Multiple Chassis Fabrics 3.5.4 Common Topologies The SANbox 5602 switch supports the following topologies using the 1-Gbps/2-Gbps Fibre Channel ports: Cascade Mesh Multistage® 3.5.4.1 Cascade Topology A cascade topology describes a fabric in which the switches are connected in series. If you connect the last switch back to the first switch, you create a cascade-with-a-loop topology as shown in Figure 3-4.
0 3 – Planning Multiple Chassis Fabrics 3.5.4.2 Mesh Topology A mesh topology describes a fabric in which each chassis has at least one port directly connected to each other chassis in the fabric. Using 16-port SANbox 5602 switches the mesh fabric shown in Figure 3-5 has the following characteristics: Each link contributes up to 425 MB of bandwidth between switches, 850 MB in full duplex.
0 3 – Planning Multiple Chassis Fabrics 3.5.4.3 Multistage Topology A Multistage topology describes a fabric in which two or more edge switches connect to one or more core switches. Using 16-port SANbox 5602 switches, the Multistage fabric shown in Figure 3-6 has the following characteristics: Each link contributes up to 425 MB of bandwidth between chassis. Competition for this bandwidth is less than that of a cascade topology, but greater than that of the mesh topology.
0 3 – Planning Fabric Security 3.6 Fabric Security Fabric security consists of the following: User Account Security Fabric Services 3.6.1 User Account Security User account security consists of the administration of account names, passwords, expiration date, and authority level. If an account has Admin authority, all management tasks can be performed by that account in both SANsurfer Switch Manager™ and the Telnet command line interface. Otherwise only monitoring tasks are available.
0 3 – Planning Fabric Management 3.7 Fabric Management The SANsurfer Switch Manager application and CLI execute on a management workstation that provides for the configuration, control, and maintenance of multiple fabrics. Supported platforms include Windows, Solaris, and Linux. The application can be installed and executed on the workstation, or you can run the SANsurfer Switch Manager web applet that is resident on the switch.
3 – Planning Fabric Management 0 Notes 3-16 59096-00 A
Section 4 Installation This section describes how to install and configure the SANbox 5602 switch. It also describes how to load new firmware and how to recover a disabled switch. 4.1 Site Requirements Consider the following items when installing a SANbox 5602 switch: Fabric Management Workstation Switch Power Requirements Environmental Conditions 4.1.
0 4 – Installation Installing a Switch 4.1.3 Environmental Conditions Consider the factors that affect the climate in your facility such as equipment heat dissipation and ventilation. The switch requires the following operating conditions: Operating temperature range: 5 – 40°C (41 – 104°F) Relative humidity: 15 – 80%, non-condensing 4.2 Installing a Switch Unpack the switch and accessories.
0 4 – Installation Installing a Switch Installing a SANbox 5602 switch involves the following steps: 1. Mount the switch. 2. Install transceivers. 3. Connect the management workstation to the switch. 4. Configure the management workstation. 5. Install the management application. 6. Start the management application. 7. Connect the switch to the AC power source. 8. Configure the switch. 9. Cable devices to the switch. 4.2.
0 4 – Installation Installing a Switch CAUTION! If the switch is mounted in a closed or multi-unit rack assembly, make sure that the operating temperature inside the rack enclosure does not exceed the maximum rated ambient temperature. Refer to “Environmental” on page A-4. Do not restrict chassis air flow. Allow 16 cm (6.5 in) minimum clearance at the front and rear of the switch (surface mount) or rack for service access and ventilation.
0 4 – Installation Installing a Switch If you are using the 10-Gbps ports, remove the port covers by the cover tabs using your fingers or pliers as shown in Figure 4-2. A L A L A L L A L 16 A A L 17 A L 18 A L 19 A Figure 4-2. Removing 10-Gbps Port Covers To install XPAK switch stacking cables, position the cable connectors with the circuit board toward the mid line of the respective switch faceplates as shown in Figure 4-3.
0 4 – Installation Installing a Switch 4.2.3 Connect the Workstation to the Switch You can manage the switch using SANsurfer Switch Manager or the command line interface. SANsurfer Switch Manager requires an Ethernet connection to the switch. The command line interface can use an Ethernet connection or a serial connection.
0 4 – Installation Installing a Switch 4.2.4 Configure the Workstation If you plan to use the command line interface to configure and manage the switch, you must configure the workstation. This involves setting the workstation IP address for Ethernet connections, or configuring the workstation serial port. If you plan to use SANsurfer Switch Manager to manage the switch, the Configuration Wizard manages the workstation IP address for you – proceed to “Install the Management Application” on page 4-9. 4.2.
0 4 – Installation Installing a Switch 4.2.4.2 Configuring the Workstation Serial Port To configure the worksation serial port, do the following: 1. Connect a null modem F/F DB9 cable from a COM port on the management workstation to the RS-232 serial port on the switch. 2. Configure the workstation serial port according to your platform: For Windows: a. Open the HyperTerminal application. Choose the Start button, select Programs, Accessories, HyperTerminal, and HyperTerminal. b.
0 4 – Installation Installing a Switch 4.2.5 Install the Management Application You can manage the switch using SANsurfer Switch Manager as a standalone application or as a part of SANsurfer Management Suite™. SANsurfer Management Suite is QLogic’s integrated fabric management application, managing both HBAs and switches. If your switch was shipped with a SANsurfer Switch Manager Disk, refer to “SANsurfer Switch Manager” on page 4-9 for instructions on how to install SANsurfer Switch Manager.
0 4 – Installation Installing a Switch For a Linux workstation: 1. If a file browser does not open, double-click the CD-ROM icon to open the browser. Double click the Switch_Manager folder, then double click the Linux folder. If there is no CD-ROM icon, do the following: a. Open an xterm or other terminal window. b. Mount the CD-ROM. From a shell prompt, enter the following command: mount /mnt/cdrom c. Change directory to location of the install program: cd /mnt/cdrom/Switch_Manager/Linux 2.
0 4 – Installation Installing a Switch 4.2.5.2 SANsurfer Management Suite The following instructions describe how to install SANsurfer Management Suite and upgrade SANsurfer Switch Manager. You can install SANsurfer Management Suite (SMS) on a Windows, Linux, or Solaris workstation. Choose the instructions for your workstation: SMS Installation for Windows SMS Installation for Linux SMS Installation for Solaris 4.2.5.2.
0 4 – Installation Installing a Switch 7. When the installation is complete, start SANsurfer Management Suite using the SANsurfer file from the SANsurfer Management Suite installation directory. You can also start SANsurfer Management Suite by clicking the SANsurfer icon (if installed) on the desktop or from the Start menu. In SMS, Click the Switch tab in the left pane. From the Help menu, select About ... and make note of the version number. Close SANsurfer Management Suite. 8.
0 4 – Installation Installing a Switch 4.2.5.2.2 SMS Installation for Linux Close all programs currently running, and insert the SANsurfer Management Suite Installation Disk into the management workstation CD-ROM drive. 1. If a file browser dialog opens showing icons for the contents of the CD-ROM, double-click the Start_Here.htm file to open the SANsurfer Management Suite start page. If a file browser does not open, double-click the CD-ROM icon to open the browser.
0 4 – Installation Installing a Switch 9. When the installation is complete, start SANsurfer Management Suite using the SANsurfer file in the installation directory. Click the Switch tab from the left pane to open SANsurfer Switch Manager. From the Help menu, select About ... and make note of the release version number. Close SANsurfer Management Suite. 10.
0 4 – Installation Installing a Switch 4.2.5.2.3 SMS Installation for Solaris To install the SANsurfer Switch Manager application on Solaris from the SANsurfer Management Suite CD-ROM, do the following: 1. Insert the SANsurfer Management Suite Disk into the management workstation CD-ROM drive. If the SANsurfer Management Suite start page does not open in your default browser, do the following: a. Right-click the Workspace Menu. b. Select File, then select File Manager. c.
0 4 – Installation Installing a Switch 10. 11. To ensure that you are using the most recent version of SANsurfer Switch Manager, visit the QLogic support web page and go to Drivers, Software and Manuals. a. Select your switch model from the pull-down menu. Locate the description for SANsurfer Switch Manager for Linux under "Management Software". b. If the release version number (4.02.xx) is greater than what is currently installed on your workstation, down load the new version.
0 4 – Installation Installing a Switch To start SANsurfer Switch Manager as a standalone application, do the following. 1. Start the SANsurfer Switch Manager using one of the following methods: For Windows, double-click the SANsurfer Switch Manager shortcut, or select SANsurfer Switch Manager from Start menu, depending on how you installed the SANsurfer Switch Manager application. From a command line, you can enter the SANsurfer_Switch_Manager command: SANsurfer_Switch_Manager.
0 4 – Installation Installing a Switch 4.2.7 Connect the Switch to AC Power WARNING!! This product is supplied with a 3-wire power cable and plug for the user’s safety. Use this power cable in conjunction with a properly grounded outlet to avoid electrical shock. An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the switch chassis. It is the responsibility of the customer to ensure that the outlet is correctly wired and grounded to prevent electrical shock.
0 4 – Installation Installing a Switch WARNUNG!! Dieses Produkt wird mit einem 3-adrigen Netzkabel mit Stecker geliefert. Dieses Kabel erfüllt die Sicherheitsanforderungen und sollte an einer vorschriftsmäßigen Schukosteckdose angeschlossen werden, um die Gefahr eines elektrischen Schlages zu vermeiden.Elektrosteckdosen, die nicht richtig verdrahtet sind, können gefährliche Hochspannung an den Metallteilen des switch-Gehäuses verursachen.
0 4 – Installation Installing a Switch The Heartbeat LED indicates the results of the POST. The POST tests the condition of firmware, memories, data-paths, and switch logic circuitry. If the Heartbeat LED blinks steadily about once per second, the POST was successful, and you can continue with the installation process. Any other blink pattern indicates that an error has occurred. Refer to “Heartbeat LED Blink Patterns” on page 5-3 for more information about error blink patterns. 4.2.
0 4 – Installation Installing a Switch To configure the switch using the command line interface, do the following: 1. Open a command window according to the type of workstation and connection: Ethernet (all platforms): Open a Telnet session with the default switch IP address and log in to the switch with default account name and password (admin/password). telnet 10.0.0.1 SANbox Login: admin Password: ******* Serial – Windows: Open the HyperTerminal application on a Windows platform. a.
0 4 – Installation Install Firmware 4.2.9 Cable Devices to the Switch Connect cables to the SFP transceivers and their corresponding devices, and then energize the devices. Device host bus adapters can have SFP (or SFF) transceivers or GigaBit Interface Converters (GBIC). LC-type duplex fiber optic cable connectors are designed for SFP transceivers, while SC-type connectors are designed for GBICs. Duplex cable connectors are keyed to ensure proper orientation.
0 4 – Installation Install Firmware 4.3.1 Using SANsurfer Switch Manager to Install Firmware To install firmware using SANsurfer Switch Manager, do the following: 1. Select a switch in the topology display and double-click to open the Faceplate display. Open the Switch menu and select Load Firmware. 2. In the Firmware Upload window, click the Select button to browse and select the firmware file to be uploaded. 3. Click the Start button to begin the firmware load process.
0 4 – Installation Install Firmware 2. Enter your account name on the remote host and the IP address of the remote host. When prompted for the source file name, enter the path for the firmware image file. User Account : johndoe IP Address : 10.20.20.200 Source Filename : 4.0.2.00.04_mpc 3. When prompted to install the new firmware, enter Yes to continue or No to cancel. If possible, a non-disruptive activation will be performed. This is the last opportunity to cancel. About to install image.
0 4 – Installation Upgrading the SANbox 5602 Switch 4.4 Upgrading the SANbox 5602 Switch The SANbox 5602 product can come from the factory as an 8-, 12-, 16-, or 20-port switch capable of 1-, 2-, and 10-Gbps port speeds. Ports 0–15 are capable of 1-Gbps/2-Gbps; ports 16–19 are capable of 10-Gbps. License keys are available for purchase to enable additional ports up to the 20-port maximum and to add 4-Gbps port speed capability to ports 0–15.
4 – Installation Powering Down a Switch 0 Notes 4-26 59096-00 A
Section 5 Diagnostics/Troubleshooting Diagnostic information about the switch is available through the chassis LEDs and the port LEDs. Diagnostic information is also available through the SANsurfer Switch Manager and CLI event logs and error displays. This section describes the following types of diagnostics: Chassis Diagnostics describes the Input Power LED and System Fault LED indications. Power-On Self Test Diagnostics describe the Heartbeat LED and the port Logged-In LED indications.
5 – Diagnostics/Troubleshooting Chassis Diagnostics 0 5.1.1 Input Power LED Is Extinguished The Input Power LED illuminates to indicate that the switch logic circuitry is receiving proper voltages. If the Input Power LED is extinguished, do the following: 1. 2. 3. Inspect the power cords and connectors. Is the cord unplugged? Is the cord or connector damaged? Yes - Make necessary corrections or repairs. If the condition remains, continue. No - Continue. Inspect the AC power source.
0 5 – Diagnostics/Troubleshooting Power-On Self Test Diagnostics 5.2 Power-On Self Test Diagnostics The switch performs a series of tests as part of its power-up procedure. The POST diagnostic program performs the following tests: Checksum tests on the boot firmware in PROM and the switch firmware in flash memory Internal data loopback test on all ports Access and integrity test on the ASIC During the POST, the switch logs any errors encountered. Some POST errors are critical, others are not.
0 5 – Diagnostics/Troubleshooting Power-On Self Test Diagnostics 5.2.1.1 Internal Firmware Failure Blink Pattern An internal firmware failure blink pattern is 2 blinks followed by a two second pause. The 2-blink error pattern indicates that the firmware has failed, and that the switch must be reset. Momentarily press and release the Maintenance button to reset the switch. 2 seconds 5.2.1.2 System Error Blink Pattern A system error blink pattern is 3 blinks followed by a two second pause.
0 5 – Diagnostics/Troubleshooting Power-On Self Test Diagnostics 1. Place the switch in maintenance mode. Press and hold the Maintenance button for 2–7 seconds. Refer to “Recovering a Switch” on page 5-11 for more information about placing the switch in maintenance mode. 2. Establish a Telnet session using the default IP address 10.0.0.1. telnet 10.0.0.1 3. Enter the account name (prom) and password (prom), and press the Enter key. SANbox login: prom Password:xxxx 4.
0 5 – Diagnostics/Troubleshooting Power-On Self Test Diagnostics e. Establish communications with the switch using Telnet. Enter one of the following on the command line: telnet xxx.xxx.xxx.xxx or telnet switchname where xxx.xxx.xxx.xxx is the switch IP address and switchname is the switch name associated with the IP address. f. A Telnet window opens prompting you for a login. Enter an account name and password. The default account name and password are (admin, password). g.
0 5 – Diagnostics/Troubleshooting Power-On Self Test Diagnostics 3. Observe the air flow direction from both power supplies. Are they the same? 4. Yes - Continue. No - Determine the proper air flow direction for the switch. Replace the power supply with the incorrect air flow direction with another having the correct air flow direction. Air flow direction is marked on the power supply part number label. If the condition remains, continue.
5 – Diagnostics/Troubleshooting Power-On Self Test Diagnostics 0 5.2.2.1 E_Port Isolation A Logged-In LED error indication is often the result of E_Port isolation. An isolated E_Port is indicated by a red link in the SANsurfer Switch Manager topology display.
0 5 – Diagnostics/Troubleshooting Power-On Self Test Diagnostics 4. Display the active zone set on each switch using the Zoning Active command or the Active Zoneset tab of the SANsurfer Switch Manager topology display. Compare the zone membership between the two active zone sets. Are they the same? Yes - Contact your authorized maintenance provider. No - Deactivate one of the active zone sets or edit the conflicting zones so that their membership is the same. Reset the port.
5 – Diagnostics/Troubleshooting Power-On Self Test Diagnostics 0 Review the event browser to determine if excessive port errors are responsible for disabling the port. Look for a message that mentions one of the monitored error types indicating that the port has been disabled, then do the following: 1. 2. 3. 4. 5-10 Examine the alarm configuration for the associated error using the Show Config Threshold command or the SANsurfer Switch Manager application.
0 5 – Diagnostics/Troubleshooting Power Supply Diagnostics 5.3 Power Supply Diagnostics A power supply has a Status LED (Green) and a Fault LED (Amber) as shown in Figure 5-3. Under normal operating conditions, the Power Supply Status LED is illuminated and the Power Supply Fault LED is extinguished. Power Supply Fault LED Power Supply Status LED Figure 5-3. Power Supply LEDs Consider the following indications: Power Supply Fault LED is illuminated.
0 5 – Diagnostics/Troubleshooting Recovering a Switch In these specific cases, you can recover the switch using maintenance mode. Maintenance mode temporarily returns the switch IP address to 10.0.0.1 and provides opportunities to do the following: Unpack a firmware image file Restore the network configuration parameters to the default values Remove all user accounts and restore the Admin account name password to the default.
0 5 – Diagnostics/Troubleshooting Recovering a Switch 5.4.1 Maintenance – Exit This option closes the current login session. To log in again, enter the maintenance mode account name and password (prom, prom). To return to normal operation, momentarily press and release the Maintenance button or power cycle the switch. 5.4.2 Maintenance – Image Unpack This option unpacks and installs new firmware when the current firmware has become corrupt.
0 5 – Diagnostics/Troubleshooting Recovering a Switch 5.4.4 Maintenance – Reset User Accounts to Default This option restores the password for the Admin account name to the default (password) and removes all other user accounts from the switch. 5.4.5 Maintenance – Copy Log Files This option copies all log file buffers to a file on the switch named logfile. You can use FTP to download this file to the management workstation. You must download the logfile before resetting the switch. 5.4.
Section 6 Removal/Replacment This section describes the removal and replacement procedures for the following field replaceable units (FRU): SFP transceivers Power supplies The switch is equipped with a battery that powers the non-volatile memory. This memory stores the switch configuration. The battery is not a field replaceable unit. WARNING!! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
6 – Removal/Replacment SFP Transceiver Removal and Replacement 0 6.1 SFP Transceiver Removal and Replacement The SFP transceivers can be removed and replaced while the switch is operating without damaging the switch or the transceiver. However, transmission on the affected port will be interrupted until the transceiver installed. To remove a transceiver, gently press the transceiver into the port to release the tension, then pull on the release tab or lever and remove the transceiver.
0 6 – Removal/Replacment Power Supply Removal and Replacement To remove a power supply, unplug the power supply and loosen the two knurled fasteners with a cross-head screw driver as shown in Figure 6-1. Grasp the power supply handle and pull firmly to disengage the modular connector. Slide the power supply out of its bay. Knurled Fasteners Figure 6-1. Power Supply Removal 1. Confirm that the Heartbeat LED is showing the normal 1 blink per second.
6 – Removal/Replacment Power Supply Removal and Replacement 0 Notes 6-4 59096-00 A
Appendix A Specifications This appendix contains the specifications for the SANbox 5602 Fibre Channel switch. Refer to Section 2 General Description for the location of all connections, switches, controls, and components. A.1 Fabric Specifications Fibre Channel Protocols ................. FC-PH Rev. 4.3 FC-PH-2 FC-PH-3 FC-AL Rev 4.6 FC-AL-2 Rev 7.0 FC-FLA FC-GS FC-GS-2 FC-GS-3 FC-FG FC-Tape FC-VI FC-SW-2 Fibre Channel Element MIB RFC 2837 Fibre Alliance MIB Version 4.0 Fibre Channel Classes of Service ..
0 A – Specifications Fabric Specifications Number of Fibre Channel Ports ...... Variable and can be upgraded in the following configurations: 8 1-Gbps/2-Gbps FC ports 12 1-Gbps/2-Gbps FC ports 16 1-Gbps/2-Gbps FC ports 16 1-Gbps/2-Gbps FC ports plus 4 10-Gbps FC ports Scalability........................................ Maximum 239 switches depending on configuration Maximum User Ports ...................... > 475,000 ports depending on configuration Buffer Credits................................
0 A – Specifications Maintainability A.2 Maintainability Diagnostics ..................................... Power-On Self Test (POST) tests all functional components except SFP transceivers. Port tests include online, internal, and external tests. User Interface ................................. LED indicators Field Replaceable Units Power supplies (model 5202 only) A.3 Fabric Management Management Methods ....................
0 A – Specifications Electrical A.5 Electrical Operating voltage ........................... 90 to 240 VAC; 50 to 60 Hz Power source loading (maximum) .. 1 A at 120 VAC 0.5 A at 240 VAC Heat Output (maximum) ................. 100 watts Circuit Protection ............................ Internally fused A.6 Environmental Temperature Operating .................................. 5 to 40°C (41 to 104°F) Non-operating ........................... -40 to 70°C (-40 to 158°F) Humidity Operating ..............
0 A – Specifications Regulatory Certifications A.7 Regulatory Certifications Safety Standards ............................ UL60950:2000 CSA 22.2 No. 60950-00 (Canada) EN60950:2000 (EC) CB Scheme-IEC 60950:1999 Emissions Standards ...................... FCC Part 15B Class A ICES-03 Issue 3 VCCI Class A ITE CISPR 22, Class A EN 55022, Class A Voltage Fluctuations ....................... EN 61000-3-3 Harmonics....................................... EN 61000-3-2 Immunity ....................................
A – Specifications Regulatory Certifications 0 Notes A-6 59096-00 A
Appendix B Command Line Interface The command line interface (CLI) enables you to perform a variety of fabric and switch management tasks through an Ethernet or a serial port connection. This section describes the following: Logging On to a Switch User Accounts Working with Switch Configurations Commands B.
B – Command Line Interface User Accounts 0 B.2 User Accounts Switches come from the factory with the following user account already defined: Account name: admin Password: password Authority: Admin This user account provides full access to the switch and its configuration. After planning your fabric management needs and creating your own user accounts, consider changing the password for this account. Refer to “Commands” on page B-7 for information about authority levels.
0 B – Command Line Interface Working with Switch Configurations B.3.1 Modifying a Configuration A switch supports up to 10 configurations including the default configuration. Each switch configuration contains switch, port, port threshold alarm, and zoning configuration components. The Show Switch command displays the name of the active configuration. A configuration name can have up to 31 characters excluding the pound symbol (#), semicolon (;), and comma (,).
B – Command Line Interface Working with Switch Configurations 0 The Config Save command saves the changes you made during the Config Edit session. In this case, changes to the configuration named Default are being saved to a new configuration named config_10132003.
0 B – Command Line Interface Working with Switch Configurations You use FTP to download the configdata file to your workstation for safe keeping and to upload the file back to the switch for the restore function. To download the configdata file, open an FTP session on the switch and login with the account name images and password images. Transfer the file in binary mode with the Get command as shown: >ftp ip_address user:images password: images ftp>bin ftp>get configdata xxxxx bytes sent in xx secs.
B – Command Line Interface Working with Switch Configurations 0 The restore process replaces all configuration information on the switch and afterwards the switch is automatically reset. If the restore process changes the IP address, all management sessions are terminated. Use the Set Setup System command to return the IP configuration to the values you want. Refer to the “Set Setup Command” on page B-57.
0 B – Command Line Interface Commands B.4 Commands The command syntax is as follows: command keyword keyword [value] keyword [value1] [value2] The Command is followed by one or more keywords. Consider the following rules and conventions: Commands and keywords are case insensitive. Required keyword values appear in standard font: [value]. Optional values are shown in italics: [value]. Underlined portions of the keyword in the command format indicate the abbreviated form that can be used.
0 B – Command Line Interface Commands The command set performs monitoring and configuration tasks. Commands related to monitoring tasks are available to all account names. Commands related to configuration tasks are available only within an admin session. An account must have Admin authority to enter the Admin Start command, which opens an admin session. Refer to the “Admin Command” on page B-9. The commands and their page numbers are listed in Table B-2. Table B-2.
0 B – Command Line Interface Admin Command Admin Command Opens and closes an Admin session. The Admin session provides commands that change the fabric and switch configurations. Only one Admin session can be open on the switch at any time. An inactive Admin session will time out after a period of time which can be changed using the Set Setup System command. Refer to the “Set Setup Command” on page B-57.
B – Command Line Interface Alias Command 0 Alias Command Creates a named set of ports/devices. Aliases make it easier to assign a set of ports/devices to many zones. An alias can not have a zone or another alias as a member.
0 B – Command Line Interface Alias Command members [alias] Displays all members of the alias given by [alias]. This keyword does not require an admin session. remove [alias] [member_list] Removes the ports/devices given by [member_list] from the alias given by [alias]. Use a to delimit ports/devices in [member_list]. A port/device in [member_list] can have any of the following formats: Domain ID and port number pair (Domain ID, Port Number). Domain IDs can be 1–-239; port numbers can be 0–-255.
B – Command Line Interface Config Command 0 Config Command Manages the Fibre Channel configurations on a switch. For information about setting the port and switch configurations, refer to the “Set Config Command” on page B-39.
0 B – Command Line Interface Config Command restore Restores configuration settings to an out-of-band switch from a backup file named configdata, which must be first uploaded on the switch using FTP. You create the backup file using the Config Backup command. Use FTP to load the backup file on a switch, then enter the Config Restore command. After the restore is complete, the switch automatically resets. Refer to “Backing up and Restoring Switch Configurations” on page B-4.
B – Command Line Interface Config Command 0 The following is an example of how to create a backup file (configdata) and download the file to the workstation.
0 B – Command Line Interface Create Support Command Create Support Command Assembles all log files and switch memory data into a core dump file (dump_support.tgz zip) and prompts you to send it to a remote host. This file is useful to technical support personnel for troubleshooting switch problems. Use this command when directed by your authorized maintenance provider.
B – Command Line Interface Create Support Command Examples 0 The following is an example of the Create Support command: SANbox (admin) #> create support Log Msg: [day month date time UTC 2004][C][8400.003B][Switch][Creating the support file - this will take several seconds] FTP the dump support file to another machine? (y/n): y Enter IP Address of remote computer: 10.20.33.
0 B – Command Line Interface Date Command Date Command This command displays or sets the system date and time. To set the date and time the information string must be provided in this format: MMDDhhmmCCYY. The new date and time takes effect immediately. Network Time Protocol (NTP) must be disabled to set the time with the Date command. Refer to the “Set Setup Command” on page B-57, System keyword, for information about NTP. Authority Admin session except to display the date.
B – Command Line Interface Feature Command 0 Feature Command Adds license key features to the switch and displays the license key feature log. To order a license key contact your switch distributor or your authorized reseller. Upgrading a switch is not disruptive, nor does it require a switch reset. Authority Admin session for Add keyword only Syntax feature add [license_key] log Keywords add [license_key] Adds the feature that corresponds to the value given by [license_key].
0 B – Command Line Interface Firmware Install Command Firmware Install Command Downloads firmware from a remote host to the switch, installs the firmware, then resets the switch (without a power-on self test) to activate the firmware. If possible, a non-disruptive activation is performed.
B – Command Line Interface Hardreset Command 0 Hardreset Command Resets the switch and performs a power-on self test. This reset disrupts traffic, activates the pending firmware, and clears the alarm log. To save the alarm log before resetting, refer to the “Set Log Command” on page B-52. Authority Admin session Syntax Notes hardreset To reset the switch without a power-on self test, refer to the “Reset Command” on page B-32.
0 B – Command Line Interface Help Command Help Command Displays a brief description of the specified command, its keywords, and usage. Authority None Syntax Keywords help [command] [keyword] [command] Displays a summary of the command given by [command] and its keywords. If you omit [command], the system displays all available commands. [keyword] Displays a summary of the keyword given by [keyword] belonging to the command given by [command].
0 B – Command Line Interface History Command History Command Displays a numbered list of the previously entered commands from which you can re-execute selected commands. Authority None Syntax Notes history Examples Use the History command to provide context for the ! command: Enter ![command_string] to re-execute the most recent command that matches [command_string].
0 B – Command Line Interface Hotreset Command Hotreset Command Resets the switch for the purpose of activating the pending firmware without disrupting traffic. This command terminates all management sessions, saves all configuration information, and clears the event log. After the pending firmware is activated, the configuration is recovered. This process takes less than 80 seconds. To save the event log to a file before resetting, refer to the “Set Log Command” on page B-52.
0 B – Command Line Interface Image Command Image Command Manages and installs switch firmware. Authority Admin session Syntax image cleanup fetch [account_name] [ip_address] [file_source] [file_destination] install list unpack [file] Keywords cleanup Removes all firmware image files from the switch. All firmware image files are removed automatically each time the switch is reset.
0 B – Command Line Interface Image Command 2. Move to the folder or directory on the workstation that contains the new firmware image file. 3. Establish communications with the switch using the File Transfer Protocol (FTP). Enter one of the following on the command line: >ftp xxx.xxx.xxx.xxx or >ftp switchname where xxx.xxx.xxx.xxx is the switch IP address, and switchname is the switch name associated with the IP address. 4.
0 B – Command Line Interface Image Command 12. Wait for the unpack to complete. image unpack command result: Passed 13. A message will prompt you to reset the switch to activate the firmware. Resetting the switch is disruptive. Use the Hotreset command to attempt a non-disruptive activation. SANbox (admin) $>hotreset Examples The following is an example of the Image Install command: SANbox (admin) #> image install Warning: Installing new firmware requires a switch reset.
0 B – Command Line Interface Lip Command Lip Command Reinitializes the specified loop port. Authority Admin session Syntax Keywords lip [port_number] Examples The following is an example of the Lip command: [port_number] The number of the port to be reinitialized. Ports are numbered beginning with 0.
0 B – Command Line Interface Passwd Command Passwd Command Changes a user account’s password. Authority Admin account name and an admin session to change another account’s password; You can change you own password without an Admin session. Syntax Keywords passwd [account_name] Examples The following is an example of the Passwd command: [account_name] The user account name. To change the password for an account name other than your own, you must open an admin session with the account name Admin.
0 B – Command Line Interface Ping Command Ping Command Initiates an attempt to communicate with another switch over an Ethernet network and reports the result. Authority None Syntax ping ip_address Keywords ip_address The IP address of the switch to query. Examples The following is an example of a successful Ping command: SANbox #> ping 10.20.11.57 Ping command issued. Waiting for response... SANbox #> Response successfully received from 10.20.11.57.
0 B – Command Line Interface Ps Command Ps Command Displays current system process information. Authority None Syntax Examples ps The following is an example of the Ps command: SANbox #> ps PID B-30 PPID %CPU TIME ELAPSED COMMAND 338 327 0.0 00:00:00 3-01:18:35 cns 339 327 0.0 00:00:01 3-01:18:35 ens 340 327 0.0 00:00:21 3-01:18:35 dlog 341 327 0.1 00:05:35 3-01:18:35 ds 342 327 0.2 00:11:29 3-01:18:35 mgmtApp 343 327 0.0 00:00:04 3-01:18:35 fc2 344 327 0.
0 B – Command Line Interface Quit Command Quit Command Closes the Telnet session. Authority None Syntax Notes quit, exit, or logout 59096-00 A You can also enter Control-D to close the Telnet session.
0 B – Command Line Interface Reset Command Reset Command Resets the switch configuration parameters. If you omit the keyword, the default is Reset Switch. Authority Admin session Syntax reset config [config_name] factory port [port_number] snmp switch (default) system zoning Keywords config [config_name] Resets the configuration given by [config_name] to the factory default values for switch, port, port threshold alarm, and zoning configuration.
0 B – Command Line Interface Reset Command Clears the event log. To save the event log before resetting, refer to the “Set Log Command” on page B-52. To reset the switch with a power-on self test, refer to the “Hardreset Command” on page B-20. To reset the switch without disrupting traffic, refer to the “Hotreset Command” on page B-23. system Resets the system configuration settings to the factory default values. Refer to Table B-8 for system configuration default values.
0 B – Command Line Interface Reset Command Table B-4.
0 B – Command Line Interface Reset Command Table B-5.
0 B – Command Line Interface Reset Command Table B-7. SNMP Configuration Defaults Parameter Default SNMPEnabled True Contact Location Description SANbox 5602 FC Switch Trap [1-5] Address Trap 1: 10.0.0.254; Traps 2–5: 0.0.0.0 Trap [1-5] Port 162 Trap [1-5] Severity Warning Trap [1-5] Version 2 Trap [1-5] Enabled False ObjectID 1.3.6.1.4.1.1663.1.1.1.1.24 AuthFailureTrap False ProxyEnabled True Table B-8.
0 B – Command Line Interface Set Command Set Command Sets a variety of switch parameters. Authority Admin session for all keywords except Alarm, Beacon, and Pagebreak which are available without an Admin session. Syntax set alarm [option] beacon [state] config [option] log [option] pagebreak [state] port [option] setup [option] switch [state] Keywords alarm [option] Controls the display of alarms in the session output stream or clears the alarm log.
B – Command Line Interface Set Command 0 pagebreak [state] Specifies how much information is displayed on the screen at a time according to the value given by [state]. This keyword does not require an admin session. [state] can be one of the following: on Limits the display of information to 20 lines at a time. The page break functions affects the following commands: Alias (List, Members), Show (Alarm, Log), Zone (List, Members), Zoneset (List, Zones), Zoning (Active, List).
0 B – Command Line Interface Set Config Command Set Config Command Sets switch, port, port threshold alarm, and zoning configuration parameters. The changes you make with this command are not retained when you reset or power cycle the switch unless you save them using the Config Save command. Refer to the “Config Command” on page B-12.
0 B – Command Line Interface Set Config Command Table B-9. Set Config Port Parameters (Continued) Parameter B-40 Description PortType Port type: 1-Gbps/2-Gbps Ports: GL, G, F, FL, Donor. The default is GL. 10-Gbps Ports: G SymbolicPortName Descriptive name for the port. The name can be up to 32 characters excluding #, semicolon (;), and comma (,). The default is Port n where n is the port number. ALFairness (1-Gbps/2-Gbps ports only) Arbitration loop fairness.
0 B – Command Line Interface Set Config Command Table B-9. Set Config Port Parameters (Continued) Parameter 59096-00 A Description AutoPerfTuning Automatic performance tuning for FL_Ports only. The default is True. If AutoPerfTuning is enabled (True) and the port is an FL_Port, MFSEnable is automatically enabled. LCFEnable and VIEnable are overridden to False. If AutoPerfTuning is disabled (False), MFSEnable, LCFEnable, and VIEnable retain their original values.
0 B – Command Line Interface Set Config Command Table B-9. Set Config Port Parameters (Continued) Parameter Description IOStreamGuard I/O Stream Guard. Enables or disables the suppression of RSCN messages. IOStreamGuard can have the following values: Enable – Suppresses the reception of RSCN messages from other ports for which IOStreamGuard is enabled. Disable – Allows free transmission and reception of RSCN messages.
0 B – Command Line Interface Set Config Command Table B-10. Set Config Switch Parameters (Continued) Parameter 59096-00 A Description FDMIEnabled Fabric Device Monitoring Interface. Enables (True) or disables (False) the monitoring of target and initiator device information. FDMIEntries The number of device entries to maintain in the FDMI database. Enter a number from 0–1000. The default is 1000. DefaultDomainID Default domain ID. The default is 1.
0 B – Command Line Interface Set Config Command Table B-10. Set Config Switch Parameters (Continued) Parameter B-44 Description InteropMode Propagates just the active zone set throughout the fabric (True, compliant) or the entire zoning database (False, non-compliant). The default is True. LegacyAddressFormat Available only when the InteropMode parameter is False, this parameter enables (True) or disables (False) the use of legacy address formatting for interoperating with non-FC-SW-2 switches.
0 B – Command Line Interface Set Config Command threshold Initiates a configuration session by which to generate and log alarms for selected events. The system displays each event, its triggers, and sampling window one line at a time and prompts you for a value. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. These parameters must be saved in a configuration and activated before they will take effect.
0 B – Command Line Interface Set Config Command zoning Initiates an editing session in which to change switch zoning attributes. The system displays each parameter one line at a time and prompts you for a value. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. Table B-12.
0 Examples B – Command Line Interface Set Config Command The following is an example of the Set Config Port command: SANbox #> admin start SANbox (admin) #> config edit SANbox (admin-config) #> set config port 1 A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
0 B – Command Line Interface Set Config Command The following is an example of the Set Config Port command for a 10-Gbps port: SANbox #> admin start SANbox (admin) #> config edit SANbox (admin-config) #> set config port 16 A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
0 B – Command Line Interface Set Config Command The following is an example of the Set Config Switch command: SANbox #> admin start SANbox (admin) #> config edit SANbox (admin-config) #> set config switch A list of attributes with formatting and default values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
0 B – Command Line Interface Set Config Command The following is an example of the Set Config Threshold command: SANbox #> admin start SANbox (admin) #> config edit SANbox (admin-config) #> set config threshold A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
0 B – Command Line Interface Set Config Command The following is an example of the Set Config Zoning command. SANbox #> admin start SANbox (admin) #> config edit SANbox (admin-config) #> set config zoning A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
B – Command Line Interface Set Log Command 0 Set Log Command Specifies the events to record in the event log and display on the screen. You determine what events to record in the switch event log using the Component, Level, and Port keywords. You determine what events are automatically displayed on the screen using the Display keyword. Alarms are always displayed on the screen.
0 B – Command Line Interface Set Log Command None Monitor none of the component events. Other Monitors other miscellaneous events. Port Monitors all port events. SNMP Monitors all SNMP events. Switch Monitors switch management events. Zoning Monitors zoning conflict events. display [filter] Specifies the log events to automatically display on the screen according to the event severity levels given by [filter]. [filter] can be one of the following values: Critical Critical severity level events.
B – Command Line Interface Set Log Command 0 Info Monitors informative, warning, and critical events. The informative level describes routine events associated with a normal fabric. This is the default severity level. None Monitors none of the severity levels. port [port_list] Specifies one or more ports to monitor for events. Choose one of the following values: [port_list] Specifies port or ports to monitor. Use a to delimit values in the list. Ports are numbered beginning with 0.
0 B – Command Line Interface Set Port Command Set Port Command Sets port state and speed for the specified port temporarily until the next switch reset or new configuration activation. This command also clears port counters. Authority Admin session except for the Clear keyword. Syntax set port [port_number] bypass [alpa] clear enable speed [transmission_speed] state [state] Keywords [port_number] Specifies the port. Ports are numbered beginning with 0.
B – Command Line Interface Set Port Command 0 Offline Places the port offline. This prevents the port from receiving signal and accepting a device login. Diagnostics Prepares the port for testing. This prepares the port for testing and prevents the port from accepting a device login. Down Disables the port by removing power from the port lasers.
0 B – Command Line Interface Set Setup Command Set Setup Command Changes SNMP and system configuration settings. The switch maintains one SNMP configuration and one system configuration. Authority Admin session Syntax set setup snmp system Keywords snmp Prompts you in a line-by-line fashion to change SNMP configuration settings. Table B-13 describes the SNMP fields. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. Table B-13.
0 B – Command Line Interface Set Setup Command Table B-13. SNMP Configuration Settings (Continued) Entry Description ReadCommunity Read community password that authorizes an SNMP agent to read information from the switch. This is a write-only field. The value on the switch and the SNMP management server must be the same. The read community password can be up to 32 characters excluding #, semicolon (;), and comma (,). The default is “public”.
0 B – Command Line Interface Set Setup Command Table B-14. System Configuration Settings (Continued) Entry 59096-00 A Description Eth0NetworkMask Ethernet subnet mask address. Eth0GatewayAddress Ethernet IP address gateway. AdminTimeout Amount of time in minutes the switch waits before terminating an idle Admin session. Zero (0) disables the time out threshold. The default is 30, the maximum is 1440.
0 B – Command Line Interface Set Setup Command Examples The following is an example of the Set Setup SNMP command: SANbox #> admin start SANbox (admin) #> set setup snmp A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
0 B – Command Line Interface Set Setup Command The following is an example of the Set Setup System command: SANbox (admin) #> set setup system A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
B – Command Line Interface Show Command 0 Show Command Displays fabric, switch, and port operational information.
0 B – Command Line Interface Show Command chassis Displays chassis component status and temperature. config [option] Displays switch, port, and zoning configuration attributes. Refer to the “Show Config Command” on page B-77. domains Displays list of each domain and its worldwide name in the fabric. donor Displays list of current donor configuration for all ports. fabric Displays list of each domain, symbolic name, worldwide name, node IP address, and port IP address.
0 B – Command Line Interface Show Command ns [option] Displays name server information for the specified [option]. If you omit [option], name server information for the local domain ID is displayed. [option] can have the following values: all Displays name server information for all switches and ports. [domain_id] Displays name server information for the switch given by [domain_id]. [domain_id] is a switch domain ID. [port_id] Displays name server information for the port given by [port_id].
0 B – Command Line Interface Show Command Table B-15. Show Port Parameters (Continued) Entry 59096-00 A Description EpConnects Number of times an E_Port connected through ISL negotiation. FBusy Number of times the switch sent a F_BSY because Class 2 frame could not be delivered within ED_TOV time. Number of class 2 and class 3 fabric busy (F_BSY) frames generated by this port in response to incoming frames.
0 B – Command Line Interface Show Command Table B-15. Show Port Parameters (Continued) Entry Description PrimSeqErrors Primitive sequence errors detected. RxLinkResets Number of link reset primitives received from an attached device. RxOfflineSeq Number of offline sequences received. An OLS is issued for link initialization, a Receive & Recognize Not_Operational (NOS) state, or to enter the offline state. TotalErrors Total number of errors detected.
0 B – Command Line Interface Show Command support Executes a series of commands that display a complete description of the switch, its configuration, and operation. The display can be captured from the screen and used for diagnosing problems. This keyword is intended for use at the request of your authorized maintenance provider.
0 B – Command Line Interface Show Command Table B-16. Switch Operational Parameters (Continued) Parameter Description LogLevel Event severity level used to record events in the event log MaxPorts Number of ports available on the switch NumberOfResets Number of times the switch has been reset over its service life ReasonForLastReset Action that caused the last reset ActiveImageVersion - build date Active firmware image version and build date.
0 Examples B – Command Line Interface Show Command The following is an example of the Show Chassis command: SANbox #> show chassis Chassis Information ------------------BoardTemp (1) - Degrees Celsius 36 FanStatus (1) Good FanStatus (2) Good FanDirection (1) BackToFront FanDirection (2) BackToFront PowerSupplyStatus (1) Good PowerSupplyStatus (2) Good HeartBeatCode 1 HeartBeatStatus Normal The following is an example of the Show Domains command: SANbox #> show domains Principal switch is
0 B – Command Line Interface Show Command The following is an example of the Show FDMI command: SANbox #> show fdmi HBA ID PortID Manufacturer Model Ports -------- ------ --------------- ------- ----- 21:01:00:e0:8b:27:aa:bc 610000 QLogic Corporation QLA2342 2 21:00:00:00:ca:25:9b:96 180100 QLogic Corporation QL2330 2 The following is an example of the Show FDMI WWN command: SANbox #> show fdmi 21:00:00:e0:8b:09:3b:17 FDMI Information ---------------Manufacturer QLogic Corporation Ser
0 B – Command Line Interface Show Command The following is an example of the Show NS (local domain) command: SANbox #> show ns Seq Domain Port Port No ID Type COS PortWWN NodeWWN ------ ---- --- ------- ------- ID --- -----1 19 (0x13) 1301e1 NL 3 21:00:00:20:37:73:13:69 20:00:00:20:37:73:13:69 2 19 (0x13) 1301e2 NL 3 21:00:00:20:37:73:12:9b 20:00:00:20:37:73:12:9b 3 19 (0x13) 1301e4 NL 3 21:00:00:20:37:73:05:26 20:00:00:20:37:73:05:26 4 19 (0x13) 130d00 N 3 21:01:00:e0:8b:27:a7:bc
0 B – Command Line Interface Show Command The following is an example of the Show Interface command: SANbox #> show interface eth0 Link encap:Ethernet HWaddr 00:C0:DD:00:BD:ED inet addr:10.20.68.107 Bcast:10.20.68.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Mask:255.255.255.0 Metric:1 RX packets:4712 errors:0 dropped:0 overruns:0 frame:0 TX packets:3000 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:415313 (405.5 Kb) TX bytes:716751 (699.
0 B – Command Line Interface Show Command The following is an example of the Show Port command: SANbox #> show port 1 Port Number: 1 ------------ 59096-00 A AdminState Online OperationalState Online AsicNumber 0 PerfTuningMode Normal AsicPort 1 PortID 0e0800 ConfigType GL PortWWN 20:08:00:c0:dd:03:d5:94 DiagStatus Passed RunningType E EpConnState Connected MediaPartNumber PL-XPL-VC-SG3-22 EpIsoReason NotApplicable MediaRevision 1 IOStreamGuard Disabled MediaType 400-M5-SN-I
0 B – Command Line Interface Show Command The following is an example of the Show Switch command: SANbox #> show switch Switch Information -----------------SymbolicName sw .108 SwitchWWN 100000c0dd00bc56 SwitchType SANbox 5602 BootVersion Vx.x.x.x-0 (day month date time year) CreditPool 0 DomainID 19 (0x13) FirstPortAddress 130000 FlashSize - MBytes 128 LogLevel Critical MaxPorts 20 NumberOfResets 15 ReasonForLastReset PowerUp ActiveImageVersion - build date Vx.x.x.
0 B – Command Line Interface Show Command The following is an example of the Show Topology command for port 1: SANbox #> show topology 1 Local Link Information ---------------------PortNumber 1 PortID 650100 PortWWN 20:01:00:c0:dd:00:91:11 PortType F Remote Link Information ----------------------Device 0 NodeWWN 50:80:02:00:00:06:d5:38 PortType NL Description (NULL) IPAddress 0.0.0.0 Device 1 NodeWWN 20:00:00:20:37:2b:08:c9 PortType NL Description (NULL) IPAddress 0.0.0.
0 B – Command Line Interface Show Command The following is an example of the Show Version command: SANbox #> show version ***************************************************** * * * Command Line Interface SHell (CLISH) * * * ***************************************************** B-76 SystemDescription SANbox 5602 FC Switch Eth0NetworkAddress 10.20.11.
0 B – Command Line Interface Show Config Command Show Config Command Displays switch, port, alarm threshold, and zoning for the current configuration. Authority None Syntax show config port [port_number] switch threshold zoning Keywords port [port_number] Displays configuration parameters for the port number given by [port_number]. Ports are numbered beginning with 0. If [port_number] is omitted, all ports are specified. switch Displays configuration parameters for the switch.
0 B – Command Line Interface Show Config Command This an example of the Show Config Port command for a 10-Gbps port: SANbox #> show config port 16 Configuration Name: default ------------------Port Number: 16 -----------AdminState Online LinkSpeed 10Gb/s PortType G SymbolicName 10G-16 DeviceScanEnabled True ForceOfflineRSCN False AutoPerfTuning False LCFEnabled False MFSEnabled False MSEnabled True IOStreamGuard Disabled VIEnabled False PDISCPingEnabled True The following is an e
0 B – Command Line Interface Show Config Command The following is an example of the Show Config Threshold command: SANbox #> show config threshold Configuration Name: default ------------ Threshold Configuration Information ----------------------------------ThresholdMonitoringEnabled False CRCErrorsMonitoringEnabled True RisingTrigger 25 FallingTrigger 1 SampleWindow 10 DecodeErrorsMonitoringEnabled True 1 RisingTrigger 25 FallingTrigger 0 SampleWindow 10 ISLMonitoringEnabled True Ris
0 B – Command Line Interface Show Config Command The following is an example of the Show Config Zoning command: SANbox #> show config zoning Configuration Name: default ------------------- Zoning Configuration Information -------------------------------- B-80 InteropAutoSave True DefaultVisibility All 59096-00 A
0 B – Command Line Interface Show Log Command Show Log Command Displays the contents of the log or the parameters used to create and display entries in the log. The log contains a maximum of 1200 entries. When the log reaches its entry capacity, subsequent entries overwrite the existing entries, beginning with the oldest.
B – Command Line Interface Show Log Command 0 Zoning Monitors zoning conflict events. display [filter] Displays log events on the screen according to the component or severity level filter given by [filter]. [filter] can be one of the following: Info Displays all informative events. Warning Displays all warning events. Critical Displays all critical events. Eport Displays all events related to E_Ports. Mgmtserver Displays all events related to the management server.
0 Examples B – Command Line Interface Show Log Command The following is an example of the Show Log Component command: SANbox #> show log component Current settings for log -----------------------FilterComponent NameServer MgmtServer Zoning Switch Blade Port Eport Snmp The following is an example of the Show Log Level command: SANbox #> show log level Current settings for log -----------------------FilterLevel Info DisplayLevel Critical The following is an example of the Show Log Options command: SAN
B – Command Line Interface Show Perf Command 0 Show Perf Command Displays port performance in frames/second and bytes/second. If you omit the keyword, the command displays data transmitted (out), data received (in), and total data transmitted and received in frames/second and bytes per second.
0 B – Command Line Interface Show Perf Command errors [port_number] Displays continuous error counts for the port group (0–15 or 16–19) that includes [port_number]. If you omit [port_number], ports 0–15 are displayed. Type “q” and press the Enter key to stop the display.
0 B – Command Line Interface Show Perf Command The following is an example of the Show Perf Byte command: SANbox #> show perf byte Displaying bytes/sec (total)...
0 B – Command Line Interface Show Setup Command Show Setup Command Displays the current SNMP and system settings. Authority None Syntax show setup mfg snmp system Keywords mfg Displays manufacturing information about the switch. snmp Displays the current SNMP settings. system Displays the current system settings.
0 B – Command Line Interface Show Setup Command The following is an example of the Show Setup Snmp command: SANbox #> show setup snmp SNMP Information ---------------- B-88 SNMPEnabled True Contact Location N_107 System Test Lab Description SANbox 5602 FC Switch Trap1Address 10.0.0.254 Trap1Port 162 Trap1Severity warning Trap1Version 2 Trap1Enabled False Trap2Address 0.0.0.
0 B – Command Line Interface Show Setup Command The following is an example of the Show Setup System command: SANbox #> show setup system System Information ------------------ 59096-00 A Eth0NetworkDiscovery Static Eth0NetworkAddress 10.20.11.32 Eth0NetworkMask 255.255.252.0 Eth0GatewayAddress 10.20.8.254 AdminTimeout 30 InactivityTimeout 0 LocalLogEnabled True RemoteLogEnabled False RemoteLogHostAddress 10.0.0.254 NTPClientEnabled True NTPServerAddress 51.68.85.
B – Command Line Interface Shutdown Command 0 Shutdown Command Terminates all data transfers on the switch at convenient points and closes the Telnet session. Always power cycle the switch after entering this command. Authority Admin session Syntax Notes shutdown Always use this command to perform an orderly shut down before removing power from the switch. When the shutdown is complete, the Heartbeat LED is extinguished.
0 B – Command Line Interface Test Command Test Command Tests ports using internal (SerDes level), external (transceiver), and online loopback tests. Internal and external tests require that the port be placed in diagnostic mode. Refer to the “Set Command” on page B-37 for information about changing the port administrative state. While the test is running, the remaining ports on the switch remain fully operational.
0 B – Command Line Interface Test Command Examples To run an internal or external port test, do the following: 1. To start an admin session, enter the following command and press the Enter key. admin start 2. Place the port in Diagnostics mode, enter the following command (x = port number) and press the Enter key. set port x state diagnostics 3.
0 B – Command Line Interface Test Command 3. A series of test parameters are displayed on the screen. Press the Enter key to accept each default parameter value, or type a new value for each parameter and press the Enter key. The TestLength parameter is the number of frames sent, the FrameSize (256 byte maximum in some cases) parameter is the number of bytes in each frame, and the DataPattern parameter is the pattern in the payload.
0 B – Command Line Interface Uptime Command Uptime Command Displays the elapsed up time since the switch was last reset and reset method. A hot reset or non-disruptive firmware activation does not reset the elapsed up time reported by this command.
0 B – Command Line Interface User Command User Command Administers and displays user accounts. Authority Admin account name and an Admin session. The Accounts and List keywords are available to all account names without an Admin session. Syntax user accounts add delete [account_name] edit list Keywords accounts Displays all user accounts that exist on the switch. This keyword is available to all account names without an Admin session. add Add a user account to the switch.
0 B – Command Line Interface User Command Examples The following is an example of the User Accounts command: SANbox (admin) #> user accounts Current list of user accounts ----------------------------images (admin authority = False, never expires) admin (admin authority = True , never expires) chuckca (admin authority = False, expires in < 50 days) gregj (admin authority = True , expires in < 100 days) fred (admin authority = True , never expires) The following is an example of the User Add com
0 B – Command Line Interface User Command The following is an example of the User Delete command: SANbox (admin) #> user del user3 The user account will be deleted. Please confirm (y/n): [n] y The following is an example of the User List command: SANbox (admin) #> user list 59096-00 A User Ethernet Addr-Port Logged in Since ---- ------------------ --------------- admin@OB-session1 10.20.68.108-1031 day month date time year admin@OB-session2 10.20.68.
0 B – Command Line Interface Whoami Command Whoami Command Displays the account name, session number, and switch domain ID for the Telnet session.
0 B – Command Line Interface Zone Command Zone Command Manages zones and zone membership on a switch. Authority Admin session and a Zoning Edit session. Refer to the “Zoning Command” on page B-105 for information about starting a Zoning Edit session. The List, Members, and Zonesets keywords are available without an Admin session.
0 B – Command Line Interface Zone Command list Displays a list of all zones and the zone sets of which they are components. This keyword does not require an Admin session. members [zone] Displays all members of the zone given by [zone]. This keyword does not require an Admin session. remove [zone] [member_list] Removes the ports/devices given by [member_list] from the zone given by [zone]. Use a to delimit aliases and ports/devices in [member_list].
0 Examples B – Command Line Interface Zone Command The following is an example of the Zone List command: SANbox #> zone list Zone ZoneSet ------------------wwn_b0241f zone_set_1 wwn_23bd31 zone_set_1 wwn_221416 zone_set_1 wwn_2215c3 zone_set_1 wwn_0160ed zone_set_1 wwn_c001b0 zone_set_1 wwn_401248 zone_set_1 wwn_02402f zone_set_1 wwn_22412f zone_set_1 The following is an example of the Zone Members command: SANbox #> zone members wwn_b0241f Current List of Members for Zone: wwn_b0241f -------
B – Command Line Interface Zone Command 0 The following is an example of the Zone Zonesets command: SANbox #> zone zonesets zone1 Current List of ZoneSets for Zone: zone1 ---------------------------------zone_set_1 B-102 59096-00 A
0 B – Command Line Interface Zoneset Command Zoneset Command Manages zone sets and component zones across the fabric. Authority Admin session and a Zoning Edit session. Refer to the “Zoning Command” on page B-105 for information about starting a Zoning Edit session. The Active, List, and Zones keywords are available without an Admin session. You must close the Zoning Edit session before using the Activate and Deactivate keywords.
0 B – Command Line Interface Zoneset Command list Displays a list of all zone sets. This keyword does not require an Admin session. remove [zone_set] [zone_list] Removes a list of zones given by [zone_list] from the zone set given by [zone_set]. Use a to delimit zone names in [zone_list]. If [zone_set] is the active zone set, the zone will not be removed until the zone set has been deactivated.
0 B – Command Line Interface Zoning Command Zoning Command Opens a Zoning Edit session in which to create and manage zone sets and zones. Refer to the “Zone Command” on page B-99 and the “Zoneset Command” on page B-103. Authority Admin session except for the Active, History, Limits, and List keywords. Syntax zoning active cancel clear edit history limits list restore save Keywords active Displays information for the active zone set including component zones and zone members.
0 B – Command Line Interface Zoning Command limits Displays the number of zone sets, zones, aliases, members per zone, members per alias, and total members in the zoning database. This keyword also displays the switch zoning database limits, excluding the active zone set, which are described in Table B-17. This keyword does not require an Admin session. Table B-17.
0 Examples B – Command Line Interface Zoning Command The following is an example of the Zoning Edit command: SANbox #> admin start SANbox (admin) #> zoning edit SANbox (admin-zoning) #> . . SANbox (admin-zoning) #> zoning cancel Zoning edit mode will be canceled.
0 B – Command Line Interface Zoning Command The following is an example of the Zoning List command: SANbox #> zoning list Active ZoneSet Information ZoneSet Zone ZoneMember -------------------------------wwn wwn_b0241f 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 21:00:00:e0:8b:02:41:2f wwn_23bd31 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:23:bd:31 wwn_221416 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:14:16 wwn_2215c3 50:06:04:82:bf:d2:18:c2 50:06:04:8
0 B – Command Line Interface Zoning Command wwn_221416 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:14:16 wwn_2215c3 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:15: 59096-00 A B-109
B – Command Line Interface Zoning Command 0 Notes B-110 59096-00 A
Glossary Access Control List Zone Access Control List zoning divides the fabric for purposes of controlling discovery and inbound traffic. Arbitrated Loop A Fibre Channel topology where ports use arbitration to establish a point-to-point circuit. Active Zone Set The zone set that defines the current zoning for the fabric. Arbitrated Loop Physical Address (AL_PA) A unique one-byte value assigned during loop initialization to each NL_Port on a loop.
0 SANbox 5602 Fibre Channel Switch Installation Guide Class 2 Service A service which multiplexes frames at frame boundaries to or from one or more N_Ports wit h acknowledgment provided. Fabric Database The set of fabrics that have been opened during a SANsurfer Switch Manager session. Chassis Hop A measure of fabric latency represented by the ISL that any frame crosses when travelling from one switch to another. A frame that travels from one switch to another over an ISL experiences one chassis hop.
0 Frame Data unit consisting of a start-of-frame (SOF) delimiter, header, data payload, CRC, and an end-of-frame (EOF) delimiter. FRU Field Replaceable Unit Heartbeat LED A chassis LED that indicates the status of the internal switch processor and the results of the Power-On Self-Test. Inactive Firmware The firmware image on the switch that is not in use. Inband Management The ability to manage a switch through another switch over an inter-switch link.
0 SANbox 5602 Fibre Channel Switch Installation Guide NL_Port Node Loop Port. A Fibre Channel device port that supports arbitrated loop protocol. N_Port Node Port. A Fibre Channel device port in a point-to-point or fabric connection. NTP Network Time Protocol Pending Firmware The firmware image that will be activated upon the next switch reset. POST Power-On Self Test Power-On Self Test Diagnostics that the switch chassis performs at start up.
0 SANbox 5602 Fibre Channel Switch Installation Guide XPAK A specification authored by a consortium of companies to govern the development of small form factor 10 Gigabit modules. Zone A set of ports or devices grouped together to control the exchange of information. Zone Set A set of zones grouped together. The active zone set defines the zoning for a fabric. Zoning Database The set of zone sets, zones, and aliases stored on a switch.
SANbox 5602 Fibre Channel Switch Installation Guide 0 Notes Glossary-6 59096-00 A
Index Numerics 10/100 Base-T straight cable 4-6 10-Gbps port 2-5 A access 3-2 Access Control List zone 3-3 account name display B-98 factory B-2 ftp 5-5 maintenance mode 5-12 Activity LED 2-6, 2-8 Admin account name B-8 authority B-8 Admin command B-9 administrative state port B-55 switch B-38 air flow A-4 alarm configuration B-45 configuration display B-77 log B-37, B-62 alias add members B-10 copy B-10 create B-10 delete B-10 delete members B-11 display list B-10 display members B-11 rename B-11 Alias co
0 SANbox 5602 Fibre Channel Switch Installation Guide configuration activate B-12 backup B-12 copy B-12 delete B-12 edit B-12 file 5-5 file system error 2-2, 5-4, 5-6 list B-12 remove 5-14 reset B-32 restore B-13 restore default 5-13 save B-13 controls 2-2 Create Support command B-15 credits 3-4, A-2 critical error 5-3 D Date command B-17 device cabling 4-22 description 3-1 performance 3-7 diagnostics 5-1, 5-3, A-3 dimensions A-3 disk space 4-1 distance 3-4 domain ID conflict 5-8 description 3-8 display
0 SANbox 5602 Fibre Channel Switch Installation Guide firmware failure 5-4 image file B-24 install with CLI 4-23, B-19 install with SANsurfer Switch Manager 4-23 list image files B-24 non-disruptive activation 4-22, B-23 remove image files B-24 retrieve image file B-24 unpack image 5-13, B-24 version B-68 Firmware Install command B-19 FL_Port 2-7 flash memory 2-2 four-switch stacking 3-10 frame size A-2 FRU - See Field Replaceable Unit FTP - See File Transfer Protocol G G_Port 2-7 GBIC - See GigaBit Inte
0 SANbox 5602 Fibre Channel Switch Installation Guide maintenance exit 5-13 interface A-3 menu 5-12 mode 2-2, 2-3, 5-3, 5-12 Maintenance button 2-2, 2-3, 5-12 management application 4-9 workstation 2-8, 4-6 manufacturer information B-87 marking A-5 media type A-2 memory activity B-63 flash 2-2 workstation 4-1 mesh topology 3-12 minicom 4-8 Multi-Frame Sequence bundling B-41 multiple chassis fabrics 3-6 Multistage topology 3-13 N name server display B-64 zone 3-3 network configuration reset B-33 interface
SANbox 5602 Fibre Channel Switch Installation Guide POST - See Power On Self Test power consumption A-4 down switch 4-25 requirements 4-1 source loading A-4 supply 2-10, 6-2 power on self test description 4-19, 5-3 log B-66 power supply diagnostics 5-11 Power Supply Fault LED 5-11 Power Supply Status LED 5-11 principal priority 3-8 switch 3-8 processor 4-1 Ps command B-30 Q Quit command B-31 R rack mount 4-3 recovering a switch 5-11 Registered State Change Notification B-42 regulatory certifications A-5
0 SANbox 5602 Fibre Channel Switch Installation Guide switch administrative state B-38 configuration 4-20, B-42 configuration display B-77 hard reset B-20 management 2-11 manufacturer information B-87 operational information B-67 power down 4-25 power up 4-19 recovery 5-11 reset 2-2, 5-14, B-94 reset without POST B-32 specifications A-1 upgrade 2-5, 3-6, 4-25 system error 5-4 processor A-2 system configuration change B-58 display B-87 System Fault LED 2-4, 5-2 T table mount 4-3 temperature error 5-6 oper
0 SANbox 5602 Fibre Channel Switch Installation Guide zone set activate B-103 active B-105 add member zone B-103 copy B-103 create B-103 deactivate B-33, B-103 delete B-103 delete member zone B-104 display B-104 display active B-103 display members B-104 display zones B-100 rename B-104 zone set definition 3-2 Zoneset command B-103 zoning configuration B-46 configuration display B-77 database 3-2, B-33 edit B-105 history B-105 limits 3-2, B-106 list definitions B-106 revert changes B-106 save edits B-106
Index – Index 0 Notes Index-8 59096-00 A
