R Simplify SANbox 5600 Series Fibre Channel Switch Installation Guide Firmware Version 5.
S SANbox 5600 Series Fibre Channel Switch Installation Guide Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for illustrative purposes only.
Table of Contents Section 1 Introduction 1.1 1.2 1.3 1.4 1.5 1.6 1.6.1 1.6.2 Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SANbox 5600 Series Fibre Channel Switch Installation Guide S 2.1.2 2.1.2.1 2.1.2.2 2.1.2.3 2.2 2.2.1 2.2.1.1 2.2.1.2 2.2.2 2.2.3 2.3 2.4 2.5 2.6 2.6.1 2.6.2 2.6.3 2.6.4 2.6.5 2.6.6 Chassis LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input Power LED (Green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heartbeat LED (Green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Fault LED (Amber). . . . . . . . . . . . . . . . . . .
A SANbox 5600 Series Fibre Channel Switch Installation Guide 3.7 3.7.1 3.7.2 3.7.2.1 3.7.2.2 3.7.2.3 3.7.3 3.8 Fabric Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connection Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Device Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Security Example: Switches and HBAs . . . . . . . . . . . . . . . . . . .
SANbox 5600 Series Fibre Channel Switch Installation Guide S 5.2.1 5.2.1.1 5.2.1.2 5.2.1.3 5.2.1.4 5.2.2 5.2.2.1 5.2.2.2 5.3 5.4 5.4.1 5.4.2 5.4.3 5.4.4 5.4.5 5.4.6 5.4.7 5.4.8 5.4.9 Heartbeat LED Blink Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal Firmware Failure Blink Pattern . . . . . . . . . . . . . . . . . . . System Error Blink Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuration File System Error Blink Pattern . . . . . . . . . . . . .
A SANbox 5600 Series Fibre Channel Switch Installation Guide Admin Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alias Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CIM Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CIMListener Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CIMSubscription Command. . . . . . . . . . . . . . . . . . . . . . .
S SANbox 5600 Series Fibre Channel Switch Installation Guide Zone Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-131 Zoneset Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-135 Zoning Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-138 Glossary Index Figures Figure Page 2-1 SANbox 5600 Series Fibre Channel Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A SANbox 5600 Series Fibre Channel Switch Installation Guide Tables Table 2-1 3-1 3-2 4-1 B-1 B-2 B-3 B-4 B-5 B-6 B-7 B-8 B-9 B-10 B-11 B-12 B-13 B-14 B-15 B-16 B-17 B-18 B-19 B-20 B-21 B-22 B-23 B-24 B-25 B-26 B-27 B-28 B-29 Serial Port Pin Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Zoning Database Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port-to-Port Latency . . . . . . . . . . . . . . .
SANbox 5600 Series Fibre Channel Switch Installation Guide S Page x 59096-02 C
Section 1 Introduction This manual describes the features and installation of the SANbox® 5600 Fibre Channel switch, firmware version 5.0. This includes the model 5600 switch and the model 5602 switch with dual replaceable power supplies.
S 1 – Introduction Related Materials 1.2 Related Materials The following manuals and materials are referenced in the text and/or provide additional information. SANbox 5600 Series Switch Management User’s Guide, publication number 59097-02. QLogic Switch Interoperability Guide v3.0. This PDF document can be downloaded at http://www.qlogic.com/interopguide/info.asp#inter. Fibre Channel-Arbitrated Loop (FC-AL-2) Rev. 6.8. Fibre Channel-10-bit Interface Rev. 2.3.
A 1 – Introduction Safety Notices 1.3 Safety Notices A Warning notice indicates the presence of a hazard that has the potential of causing personal injury. 4-3, 4-20, 6-1 A Caution notice indicates the presence of a hazard that has the potential of causing damage to the equipment. 4-4, 5-15, 6-2 1.4 Sicherheitshinweise Ein Warnhinweis weist auf das Vorhandensein einer Gefahr hin, die möglicherweise Verletzungen zur Folge hat.
1 – Introduction Communications Statements S 1.6.1 Federal Communications Commission (FCC) Class A Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
A 1 – Introduction Communications Statements 1.6.4 CE Statement The CE symbol on the equipment indicates that this system complies with the EMC (Electromagnetic Compatibility) directive of the European Community (89/336/EEC) and to the Low Voltage (Safety) Directive (73/23/EEC). Such marking indicates that this system meets or exceeds the following technical standards: 59096-02 C EN60950:2000 – “Safety of Information Technology Equipment”. EN60825-1/A2:2001 – “Safety of Laser Products, Part 1".
S 1 – Introduction Laser Safety Information 1.6.5 VCCI Class A Statement This is a Class A product based on the standard of the Voluntary Control Council For Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. 1.7 Laser Safety Information This product uses Class 1 laser optical transceivers to communicate over the fiber optic conductors.
A 1 – Introduction Accessible Parts 1.9 Accessible Parts The Field Replaceable Units (FRUs) for the SANbox 5600 Series switch are the following: Power supplies (5602) Small Form-Factor Pluggable (SFP) optical transceivers XPAK optical transceivers 1.
1 – Introduction General Public License S 1.12 General Public License QLogic® Fibre Channel switches are powered by the Linux operating system. A machine-readable copy of the Linux source code is available upon written request to the following address. A nominal fee will be charged for reproduction, shipping, and handling costs in accordance with the General Public License.
A 1 – Introduction General Public License For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
1 – Introduction General Public License S You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 3. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a.
A 1 – Introduction General Public License b. c.
1 – Introduction General Public License S 7. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 8.
A 1 – Introduction General Public License 11. Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation. 12.
S 1 – Introduction General Public License 1.12.3 How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program.
A 1 – Introduction General Public License You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the program, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision' (which makes passes at compilers) written by James Hacker.
1 – Introduction Technical Support S 1.13 Technical Support Customers should contact their authorized maintenance provider for technical support of their QLogic switch products. QLogic-direct customers may contact QLogic Technical Support; others will be redirected to their authorized maintenance provider. Visit the QLogic support Web site listed in Contact Information for the latest firmware and software updates. 1.13.
A 1 – Introduction Technical Support 1.13.3 Contact Information Support Headquarters QLogic Corporation 12984 Valley View Road Eden Prairie, MN 55344-3657 USA QLogic Web Site www.qlogic.com Technical Support Web Site support.qlogic.com Technical Support Email support@qlogic.com Technical Training Email tech.training@qlogic.com North American Region Email support@qlogic.com Phone +1-952-932-4040 Fax +1 952-932-4018 Europe, Middle East, and Africa Region Email emeasupport@qlogic.
1 – Introduction Technical Support S Notes 1-18 59096-02 C
Section 2 General Description This section describes the features and capabilities of the SANbox 5600 Series Fibre Channel switches. This includes the model 5600 and the dual power supply model 5602 as shown in Figure 2-1. The following topics are described: Chassis Controls and LEDs Fibre Channel Ports Ethernet Port Serial Port Power Supplies and Fans Switch Management Fabrics are managed with the SANsurfer Switch Manager™ switch management application (version 5.
S 2 – General Description Chassis Controls and LEDs 2.1 Chassis Controls and LEDs The Maintenance button shown in Figure 2-2 is the only chassis control and is used to reset a switch or to recover a disabled switch. The chassis LEDs provide information about the switch’s operational status. These LEDS include the Input Power LED, Heartbeat LED, and the System Fault LED. To apply power to the switch, plug the power cord into the switch AC power receptacle and into a 100– 240 VAC power source.
A 2 – General Description Chassis Controls and LEDs 2.1.1 Maintenance Button The Maintenance button is a dual-function momentary switch on the front panel. Its purpose is to reset the switch or to place the switch in maintenance mode. Maintenance mode sets the IP address to 10.0.0.1 and provides access to the switch for maintenance purposes when flash memory or the resident configuration file is corrupted. Refer to ”Recovering a Switch” on page 5-12 for more information about using maintenance mode. 2.1.
S 2 – General Description Chassis Controls and LEDs 2.1.2 Chassis LEDs The chassis LEDs provide status information about switch operation. Figure 2-3 identifies the chassis LEDS on a model 5600 switch. The model 5602 switch LED arrangement is the same. Refer to ”Port LEDs” on page 2-6 for information about port LEDs. Input Power LED (Green) L 0 A L 1 A L 2 A L 3 A L 4 A L 5 A L Heartbeat LED (Green) System Fault LED (Amber) Figure 2-3. Chassis LEDs 2.1.2.
A 2 – General Description Fibre Channel Ports 2.1.2.3 System Fault LED (Amber) The System Fault LED illuminates to indicate a fault exists in the switch firmware or hardware. Fault conditions include POST errors, over temperature conditions, and power supply malfunctions. The Heartbeat LED shows a blink code for POST errors and over temperature conditions. Refer to ”Heartbeat LED Blink Patterns” on page 5-3 for more information about Heartbeat LED blink patterns.
S 2 – General Description Fibre Channel Ports The SANbox 5600 Series switch comes from the factory as an 8-, 12-, 16-, or 20-port switch, enabling ports 0–7, 0–11, 0–15, or 0–19 respectively. You can upgrade the SANbox 5600 Series switch to enable additional ports up to the 20-port maximum through the purchase of a license key. Refer to ”Upgrading the SANbox 5600 Series Switch” on page 4-28 for more information. 2.2.
A 2 – General Description Fibre Channel Ports 2.2.1.2 Port Activity LED (Green) The Activity LED indicates that data is passing through the port. Each frame that the port transmits or receives causes this LED to illuminate for 50 milliseconds. This makes it possible to observe the transmission of a single frame. When extending credits, the Activity LED for a donor port will reflect the traffic of the recipient port.
S 2 – General Description Ethernet Port E_Ports enable you to expand the fabric by connecting SANbox 5600 Series switches. SANbox 5600 Series switches self-discover all inter-switch connections. Refer to ”Multiple Chassis Fabrics” on page 3-6 for more information about multiple chassis fabrics. Refer to the SANbox 5600 Series Switch Management User’s Guide for information about defining port types. 2.
A 2 – General Description Serial Port 2.4 Serial Port The SANbox 5600 Series switch is equipped with an RS-232 serial port for maintenance purposes. Figure 2-7 shows the serial port on a model 5600 switch; the model 5602 is similar. You can manage the switch through the serial port using the CLI. Serial Port L 0 A L 1 A L 2 A L 3 A L 4 A L 5 Figure 2-7. Serial Port and Pin Identification The serial port connector requires a null-modem F/F DB9 cable.
S 2 – General Description Power Supplies and Fans 2.5 Power Supplies and Fans The model 5600 switch has a single power supply that converts 100 – 240 VAC to DC voltages for the various switch circuits. Four internal fans provide cooling. The switch monitors internal air temperature, and therefore does not monitor or report fan operational status. Air flow is front-to-back. To energize the switch, plug the power cord into the switch AC receptacle and into a 100 – 240 VAC power source.
A 2 – General Description Switch Management 2.6 Switch Management The switch supports the following management tools: SANsurfer Switch Manager SANsurfer Switch Manager Web Applet Command Line Interface SANsurfer Switch Manager Application Programming Interface Simple Network Management Protocol File Transfer Protocol 2.6.1 SANsurfer Switch Manager SANsurfer Switch Manager is a workstation-based Java® application that provides a graphical user interface for fabric management.
2 – General Description Switch Management S 2.6.3 Command Line Interface The command line interface (CLI) provides monitoring and configuration functions by which the administrator can manage the fabric and its switches. The CLI is available over an Ethernet connection or a serial connection. Refer to Appendix B Command Line Interface for more information. 2.6.
Section 3 Planning Consider the following when planning a fabric: Devices Device Access Performance Feature Licensing Multiple Chassis Fabrics Switch Services Fabric Security Fabric Management 3.1 Devices When planning a fabric, consider the number of public devices and the anticipated demand. This will determine the number of ports that are needed and in turn the number of switches. Consider how many and what types of switches are needed.
S 3 – Planning Device Access 3.2 Device Access Consider device access needs within the fabric. Access is controlled by the use of zones and zone sets. Some zoning strategies include the following: Group devices by operating system. Separate devices that have no need to communicate with other devices in the fabric or have classified data. Separate devices into department, administrative, or other functional group. Reserve a path and its bandwidth from one port to another.
A 3 – Planning Device Access 3.2.1 Soft Zones Soft zoning divides the fabric for purposes of controlling device discovery. Devices in the same soft zone automatically discover and communicate freely with all other members of the same zone. The soft zone boundary is not secure; traffic across soft zones can occur if addressed correctly. The following rules apply to soft zones: Soft zones that include members from multiple switches need not include the ports of the inter-switch links.
S 3 – Planning Performance 3.3 Performance The SANbox 5600 Series switch supports class 2 and class 3 Fibre Channel service at transmission rates of 1-, 2-, 4-, or 10-Gbps with a maximum frame size of 2148 bytes. A 1/2/4-Gbps port adapts its transmission speed to match that of the device to which it is connected prior to login when the connected device powers up. 10-Gbps ports transmit at 10-Gbps. Related performance characteristics include the following: Distance Bandwidth Latency 3.3.
A 3 – Planning Performance You can configure recipient and donor ports using the SANsurfer Switch Manager application or the Set Config command. Refer to ”Set Config Command” on page B-64 for more information. 3.3.2 Bandwidth Bandwidth is a measure of the volume of data that can be transmitted at a given transmission rate. A 1/2/4-Gbps port can transmit or receive at nominal rates of 1-Gbps, 2-Gbps, or 4-Gbps depending on the device to which it is connected.
S 3 – Planning Feature Licensing 3.4 Feature Licensing The SANbox 5600 Series switch can come from the factory as an 8-, 12-, 16-, or 20-port switch, enabling ports 0–7, 0–11, 0–15, or 0–19 respectively. You can upgrade the SANbox 5600 Series switch to enable additional ports up to the 20-port maximum through the purchase of a license key. Consider the number of ports that you require and the need for 10-Gbps ports.
A 3 – Planning Multiple Chassis Fabrics 3.5.2 Domain ID, Principal Priority, and Domain ID Lock The following switch configuration settings affect multiple chassis fabrics: Domain ID Principal priority Domain ID lock The domain ID is a unique number from 1–239 that identifies each switch in a fabric. The principal priority is a number (1–255) that determines the principal switch which manages domain ID assignments for the fabric.
S 3 – Planning Multiple Chassis Fabrics 3.5.3 Stacking You can connect up to four 20-port SANbox 5600 Series switches together through the 10-Gbps ports, thus preserving the user ports for devices. This is called stacking. The following 2-, 3-, and 4-switch stacking configurations are recommended for best performance and redundancy. Each 10-Gbps port contributes 1 GB of bandwidth between chassis with one chassis hop between any two ports.
A 3 – Planning Multiple Chassis Fabrics Figure 3-3 shows a four-switch stack of model 5600 switches using three 3-inch and three 9-inch XPAK switch stacking cables. 64 1/2/4-Gbps ports are available for devices. Figure 3-3.
S 3 – Planning Multiple Chassis Fabrics 3.5.4 Common Topologies The SANbox 5600 Series switch supports the following topologies using the 1/2/4-Gbps Fibre Channel ports: Cascade Mesh Multistage® 3.5.4.1 Cascade Topology A cascade topology describes a fabric in which the switches are connected in series. If you connect the last switch back to the first switch, you create a cascade-with-a-loop topology as shown in Figure 3-4.
A 3 – Planning Multiple Chassis Fabrics 3.5.4.2 Mesh Topology A mesh topology describes a fabric in which each chassis has at least one port directly connected to each other chassis in the fabric. Using 16-port model 5600 switches, the mesh fabric shown in Figure 3-5 has the following characteristics: Each link contributes up to 212 MB of bandwidth between switches, 425 MB in full duplex.
S 3 – Planning Multiple Chassis Fabrics 3.5.4.3 Multistage Topology A Multistage topology describes a fabric in which two or more edge switches connect to one or more core switches. Using 16-port model 5600 switches, the Multistage fabric shown in Figure 3-6 has the following characteristics: Each link contributes up to 212 MB of bandwidth between chassis. Competition for this bandwidth is less than that of a cascade topology, but greater than that of the mesh topology.
A 3 – Planning Switch Services 3.6 Switch Services You can configure your switch to suit the demands of your environment by enabling or disabling a variety of switch services. Familiarize yourself with the following switch services and determine which ones you need: 59096-02 C Telnet: Provides for the management of the switch over a Telnet connection. Disabling this service is not recommended. The default is enabled.
S 3 – Planning Fabric Security Network Time Protocol (NTP): Provides for the synchronizing of switch and workstation dates and times with an NTP server. This helps to prevent invalid SSL certificates and timestamp confusion in the event log. The default is disabled. Common Information Model (CIM): Provides for the management of the switch through third-party applications that use CIM. The default is enabled.
A 3 – Planning Fabric Security 3.7.1 Connection Security Connection security provides an encrypted data path for switch management methods. The switch supports the Secure Shell (SSH) protocol for the command line interface and the Secure Socket Layer (SSL) protocol for management applications such as SANsurfer Switch Manager and Common Information Module (CIM). The SSL handshake process between the workstation and the switch involves the exchanging of certificates.
S 3 – Planning Fabric Security 3.7.2 Device Security Device security provides for the authorization and authentication of devices that you attach to a switch. You can configure a switch with a group of devices against which the switch authorizes new attachments by devices, other switches, or devices issuing management server commands. Device security is configured through the use of security sets and groups. A group is a list of device worldwide names that are authorized to attach to a switch.
A 3 – Planning Fabric Security 3.7.2.1 Security Example: Switches and HBAs Consider the fabric shown in Figure 3-7. In this fabric, Switch_1, HBA_1, and Switch_2 support security while the JBOD and HBA_2 do not. The objective is to secure F_Ports and E_Ports in the fabric. To do this, configure security on the devices that support security: Switch_1, Switch_2, and HBA_1.
S 3 – Planning Fabric Security You must specify HBAs by node worldwide name. Switches can be specified by port or node worldwide name. The type of switch worldwide name you use in the switch security database must be the same as that in the HBA security database. For example, if you specify a switch with a port worldwide name in the switch security database, you must also specify that switch in the HBA security database with the same port worldwide name. b.
A 3 – Planning Fabric Security 4. Configure security on Switch_2. Create a security set (Security_Set_2) on Switch_2. a. Create a port group (Group_Port_2) in Security_Set_2. HBA_2 is the only member because HBA_2 does not support authentication. Port Group on Switch_2: Group_Port_2 HBA_2 Node WWN: 10:00:00:c0:dd:07:e3:4c Authentication: None Binding: None b. Create an ISL group (Group_ISL_2) in Security_Set_2 with Switch_1 and Switch_2 as members.
S 3 – Planning Fabric Security 3.7.2.2 Security Example: RADIUS Server Consider the fabric shown in Figure 3-8. This fabric is similar to the one shown in Figure 3-7 with the addition of Radius_1 acting as a RADIUS server.
A 3 – Planning Fabric Security 1. Configure the Radius_1 host as a RADIUS server on Switch_1 and Switch_2 to authenticate device logins. Specify the server IP address and the secret with which the switches will authenticate with the server. Configure the switches so that devices authenticate through the switches only if the RADIUS server is unavailable.
S 3 – Planning Fabric Security You must specify HBAs by node worldwide name. Switches can be specified by port or node worldwide name. The type of switch worldwide name you use in the switch security database must be the same as that in the HBA security database. For example, if you specify a switch with a port worldwide name in the switch security database, you must also specify that switch in the HBA security database with the same port worldwide name. b.
A 3 – Planning Fabric Security 5. Configure security on Switch_2. Create a security set (Security_Set_2) on Switch_2. a. Create a port group (Group_Port_2) in Security_Set_2. HBA_2 is the only member because HBA_2 does not support authentication. Port Group on Switch_2: Group_Port_2 HBA_2 Node WWN: 10:00:00:c0:dd:07:e3:4c Authentication: None Binding: None b. Create an ISL group (Group_ISL_2) in Security_Set_2 with Switch_1 and Switch_2 as members.
S 3 – Planning Fabric Security Device: HBA_2/APP_2 WWN: 10:00:00:c0:dd:07:c3:4d Security: Yes Device: HBA_1/APP_1 Security: No F_Port F_Port E_Port Device: Switch_1 Security: No Device: Switch_3 Security: No Device: Switch_2 WWN: 10:00:00:c0:dd:07:e3:4e Security: Yes FL_Port Figure 3-9. Security Example: Management Server 1. Create a security set (Security_Set_2) on Switch_2. 2. Create a Management Server group (Group_1) in Security_Set_2 with Switch_2 and HBA_2 or APP_2 as its member.
A 3 – Planning Fabric Security For MD5 authentication, create secrets. MS Group: Group_1 Switch_2 Node WWN: 10:00:00:c0:dd:07:c3:4e CT Authentication: True Hash: MD5 Secret: 9876543210fedcba9 HBA_2 or APP_2 Node WWN: 10:00:00:c0:dd:07:c3:4d CT Authentication: True Hash: MD5 Secret: fedcba9876543210 59096-02 C 3. Configure security on HBA_2 or APP_2 using the appropriate management tool. Logins between the Switch_2 and HBA_2 or APP_2 will be challenged (MD5) for their respective secrets.
S 3 – Planning Fabric Security 3.7.3 User Account Security User account security consists of the administration of account names, passwords, expiration date, and authority level. If an account has Admin authority, all management tasks can be performed by that account in both SANsurfer Switch Manager™ and the Telnet command line interface. Otherwise only monitoring tasks are available. The default account name, Admin, is the only account that can create or change account names and passwords.
A 3 – Planning Fabric Management 3.8 Fabric Management The SANsurfer Switch Manager application and CLI execute on a management workstation that provides for the configuration, control, and maintenance of multiple fabrics. Supported platforms include Windows, Solaris, and Linux. The application can be installed and executed on the workstation, or you can run the SANsurfer Switch Manager web applet that is resident on the switch.
3 – Planning Fabric Management S Notes 3-28 59096-02 C
Section 4 Installation This section describes how to install and configure the SANbox 5600 Series switch. It also describes how to load new firmware and how to recover a disabled switch. 4.1 Site Requirements Consider the following items when installing a SANbox 5600 Series switch: Fabric Management Workstation Switch Power Requirements Environmental Conditions 4.1.
S 4 – Installation Installing a Switch 4.1.2 Switch Power Requirements Power requirements are 1 Amp at 100 VAC or 0.5 A at 240 VAC. 4.1.3 Environmental Conditions Consider the factors that affect the climate in your facility such as equipment heat dissipation and ventilation. The switch requires the following operating conditions: Operating temperature range: 5 – 40°C (41 – 104°F) Relative humidity: 15 – 80%, non-condensing 4.2 Installing a Switch Unpack the switch and accessories.
A 4 – Installation Installing a Switch Installing a SANbox 5600 Series switch involves the following steps: 1. Mount the switch. 2. Install transceivers. 3. Connect the management workstation to the switch. 4. Configure the management workstation. 5. Install the management application. 6. Start the management application. 7. Connect the switch to the AC power source. 8. Configure the switch. 9. Cable devices to the switch. 4.2.
4 – Installation Installing a Switch CAUTION! S If the switch is mounted in a closed or multi-unit rack assembly, make sure that the operating temperature inside the rack enclosure does not exceed the maximum rated ambient temperature. Refer to ”Environmental” on page A-4. Do not restrict chassis air flow. Allow 16 cm (6.5 in) minimum clearance at the front and rear of the switch (surface mount) or rack for service access and ventilation.
A 4 – Installation Installing a Switch To mount a 5600 model switch in a rack without the use of rails, fasten the brackets to the switch as shown in Figure 4-2. Choose the bracket screw holes to produce the setback you want. Place the switch in the rack and fasten the bracket flanges to the rack with two screws on each side. L 0 A L 1 A L 2 A L 3 A L 4 A L 5 A L 6 A L 7 A L A L A L A L A L A L A L L A L A 16 A L 17 A L 18 A L 19 A Figure 4-2.
S 4 – Installation Installing a Switch To mount a 5600 model switch in a rack using the General Devices C-874 rail kit, you must fasten the switch brackets and inner rails to the switch as shown in Figure 4-3. Use the screws that come with the rail kit. Refer to the rail kit instructions for complete information. L 0 A L 1 A L 2 A L 3 A L 4 A L 5 A L 6 A L 7 A L A L A L A L A L A L A L L A L A 16 A L 17 A L 18 A L 19 A Figure 4-3.
A 4 – Installation Installing a Switch CAUTION! To maintain proper air flow and prevent the switch from overheating, keep covers installed in unused 10-Gbps ports. If you are using the 10-Gbps ports, remove the port covers by the cover tabs using your fingers or pliers as shown in Figure 4-4. A L A L L A L 16 A A L 17 A L 18 A L 19 A Figure 4-4.
S 4 – Installation Installing a Switch 4.2.3 Connect the Workstation to the Switch You can manage the switch using SANsurfer Switch Manager or the command line interface. SANsurfer Switch Manager requires an Ethernet connection to the switch. The command line interface can use an Ethernet connection or a serial connection.
A 4 – Installation Installing a Switch 4.2.4 Configure the Workstation If you plan to use the command line interface to configure and manage the switch, you must configure the workstation. This involves setting the workstation IP address for Ethernet connections, or configuring the workstation serial port. If you plan to use SANsurfer Switch Manager to manage the switch, the Configuration Wizard manages the workstation IP address for you – proceed to ”Install the Management Application” on page 4-11. 4.
S 4 – Installation Installing a Switch 4.2.4.2 Configuring the Workstation Serial Port To configure the workstation serial port, do the following: 1. Connect a null modem F/F DB9 cable from a COM port on the management workstation to the RS-232 serial port on the switch. 2. Configure the workstation serial port according to your platform: For Windows: a. Open the HyperTerminal application. Choose the Start button, select Programs, Accessories, HyperTerminal, and HyperTerminal. b.
A 4 – Installation Installing a Switch 4.2.5 Install the Management Application You can manage the switch using SANsurfer Switch Manager as a standalone application or as a part of SANsurfer Management Suite™. SANsurfer Management Suite is QLogic’s integrated fabric management application, managing both HBAs and switches. If your switch was shipped with a SANsurfer Switch Manager Disk, refer to ”SANsurfer Switch Manager” on page 4-11 for instructions on how to install SANsurfer Switch Manager.
S 4 – Installation Installing a Switch For a Linux platform: Open the CD and run the installation program with the following path: data/files/Management_Software/Linux/Linux_5.00.xx.xx.bin If there is no CD-ROM icon, do the following: 1. Open an xterm or other terminal window. 2. Mount the CD-ROM. From a shell prompt, enter the following: mount /mnt/cdrom 3. Change directory to the location of the install program: cd /mnt/cdrom/data/files/Management_Software/Linux 4.
A 4 – Installation Installing a Switch 4.2.5.2 SANsurfer Management Suite The following instructions describe how to install SANsurfer Management Suite and upgrade SANsurfer Switch Manager. You can install SANsurfer Management Suite (SMS) on a Windows, Linux, or Solaris workstation. Choose the instructions for your workstation: SMS Installation for Windows SMS Installation for Linux SMS Installation for Solaris 4.2.5.2.
4 – Installation Installing a Switch S 7. When the installation is complete, start SANsurfer Management Suite using the SANsurfer file from the SANsurfer Management Suite installation directory. You can also start SANsurfer Management Suite by clicking the SANsurfer icon (if installed) on the desktop or from the Start menu. In SMS, Click the Switch tab in the left pane. From the Help menu, select About ... and make note of the version number. Close SANsurfer Management Suite. 8.
A 4 – Installation Installing a Switch 4.2.5.2.2 SMS Installation for Linux Close all programs currently running, and insert the SANsurfer Management Suite Installation Disk into the management workstation CD-ROM drive. 1. If a file browser dialog opens showing icons for the contents of the CD-ROM, double-click the Start_Here.htm file to open the SANsurfer Management Suite start page. If a file browser does not open, double-click the CD-ROM icon to open the browser.
4 – Installation Installing a Switch S 9. When the installation is complete, start SANsurfer Management Suite using the SANsurfer file in the installation directory. Click the Switch tab from the left pane to open SANsurfer Switch Manager. From the Help menu, select About ... and make note of the release version number. Close SANsurfer Management Suite. 10.
A 4 – Installation Installing a Switch 4.2.5.2.3 SMS Installation for Solaris To install the SANsurfer Switch Manager application on Solaris from the SANsurfer Management Suite CD-ROM, do the following: 1. Insert the SANsurfer Management Suite Disk into the management workstation CD-ROM drive. If the SANsurfer Management Suite start page does not open in your default browser, do the following: a. Right-click the Workspace Menu. b. Select File, then select File Manager. c.
S 4 – Installation Installing a Switch 10. To ensure that you are using the most recent version of SANsurfer Switch Manager, visit the QLogic support web page and go to Drivers, Software and Manuals. a. Select your switch model from the pull-down menu. Locate the description for SANsurfer Switch Manager for Linux under "Management Software". b. If the release version number (5.00.xx) is greater than what is currently installed on your workstation, down load the new version.
A 4 – Installation Installing a Switch To start SANsurfer Switch Manager as a standalone application, do the following. 1. Start the SANsurfer Switch Manager using one of the following methods: For Windows, double-click the SANsurfer Switch Manager shortcut, or select SANsurfer Switch Manager from Start menu, depending on how you installed the SANsurfer Switch Manager application. From a command line, you can enter the SANsurfer_Switch_Manager command: SANsurfer_Switch_Manager.
S 4 – Installation Installing a Switch 4.2.7 Connect the Switch to AC Power WARNING!! This product is supplied with a 3-wire power cable and plug for the user’s safety. Use this power cable in conjunction with a properly grounded outlet to avoid electrical shock. An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the switch chassis. It is the responsibility of the customer to ensure that the outlet is correctly wired and grounded to prevent electrical shock.
A 4 – Installation Installing a Switch WARNUNG!! Dieses Produkt wird mit einem 3-adrigen Netzkabel mit Stecker geliefert. Dieses Kabel erfüllt die Sicherheitsanforderungen und sollte an einer vorschriftsmäßigen Schukosteckdose angeschlossen werden, um die Gefahr eines elektrischen Schlages zu vermeiden.Elektrosteckdosen, die nicht richtig verdrahtet sind, können gefährliche Hochspannung an den Metallteilen des switch-Gehäuses verursachen.
S 4 – Installation Installing a Switch To power up a SANbox 5600 Series switch, do the following: For a model 5600 switch, connect the power cord to the AC power receptacle on the front of the switch chassis and to a grounded AC outlet. For a model 5602 switch, connect the power cords to the power supply receptacles on the back of the switch chassis and to a grounded AC outlet.
A 4 – Installation Installing a Switch 4.2.8 Configure the Switch You can configure the switch using the SANsurfer Switch Manager application or the command line interface. To configure the switch using SANsurfer Switch Manager, click the Open Configuration Wizard radio button in the Initial Start dialog, then click the Proceed button.
S 4 – Installation Installing a Switch Serial – Windows: Open the HyperTerminal application on a Windows platform. a. Choose the Start button, select Programs, Accessories, HyperTerminal, and HyperTerminal. b. Select the connection you created earlier and choose the OK button. Serial – Linux: Open a command window and enter the following command: minicom Serial – Solaris: Open a command window and enter the following command: tip sanbox2 2.
A 4 – Installation Install Firmware 4.2.9 Cable Devices to the Switch Connect cables to the SFP transceivers and their corresponding devices, and then energize the devices. Device host bus adapters can have SFP (or SFF) transceivers or GigaBit Interface Converters (GBIC). LC-type duplex fiber optic cable connectors are designed for SFP transceivers, while SC-type connectors are designed for GBICs. Duplex cable connectors are keyed to ensure proper orientation.
S 4 – Installation Install Firmware 4.3.1 Using SANsurfer Switch Manager to Install Firmware SANsurfer Switch Manager installs the firmware and performs a non-disruptive activation if it is possible. To install firmware using SANsurfer Switch Manager, do the following: 4-26 1. Select a switch in the topology display and double-click to open the Faceplate display. Open the Switch menu and select Load Firmware. 2.
A 4 – Installation Install Firmware 4.3.2 Using the CLI to Install Firmware To install firmware using the CLI when a File Transfer Protocol (FTP) server is present on the management workstation, use the Firmware Install command. This command downloads the firmware from a remote host, installs the firmware, and performs a disruptive firmware activation. Refer to the ”Firmware Install Command” on page B-25 for more information. 1.
4 – Installation Upgrading the SANbox 5600 Series Switch S 4.4 Upgrading the SANbox 5600 Series Switch The SANbox 5600 Series product can come from the factory as an 8-, 12-, 16-, or 20-port switch, enabling ports 0–7, 0–11, 0–15, or 0–19 respectively. Ports 0–15 are capable of 1-, 2-, or 4-Gbps; ports 16–19 are capable of 10-Gbps. You can upgrade the SANbox 5600 Series switch to enable additional ports up to the 20-port maximum through the use of a license key.
Section 5 Diagnostics/Troubleshooting Diagnostic information about the switch is available through the chassis LEDs and the port LEDs. Diagnostic information is also available through the SANsurfer Switch Manager and CLI event logs and error displays. This section describes the following types of diagnostics: Chassis Diagnostics describes the Input Power LED and System Fault LED indications. Power-On Self Test Diagnostics describe the Heartbeat LED and the port Logged-In LED indications.
S 5 – Diagnostics/Troubleshooting Chassis Diagnostics The following conditions are described: Input Power LED Is Extinguished System Fault LED Is Illuminated 5.1.1 Input Power LED Is Extinguished The Input Power LED illuminates to indicate that the switch logic circuitry is receiving proper voltages. If the Input Power LED is extinguished, do the following: 1. 2. 3. Inspect the power cords and connectors.
A 5 – Diagnostics/Troubleshooting Power-On Self Test Diagnostics 5.2 Power-On Self Test Diagnostics The switch performs a series of tests as part of its power-up procedure. The POST diagnostic program performs the following tests: Checksum tests on the boot firmware in PROM and the switch firmware in flash memory Internal data loopback test on all ports Access and integrity test on the ASIC During the POST, the switch logs any errors encountered. Some POST errors are critical, others are not.
S 5 – Diagnostics/Troubleshooting Power-On Self Test Diagnostics 5.2.1.1 Internal Firmware Failure Blink Pattern An internal firmware failure blink pattern is 2 blinks followed by a two second pause. The 2-blink error pattern indicates that the firmware has failed, and that the switch must be reset. Momentarily press and release the Maintenance button to reset the switch. 2 seconds 5.2.1.2 System Error Blink Pattern A system error blink pattern is 3 blinks followed by a two second pause.
A 5 – Diagnostics/Troubleshooting Power-On Self Test Diagnostics 1. Place the switch in maintenance mode. Press and hold the Maintenance button. When the Heartbeat LED alone is illuminated, release the button. Refer to ”Recovering a Switch” on page 5-12 for more information about maintenance mode. 2. Establish a Telnet session using the default IP address 10.0.0.1. telnet 10.0.0.1 3. Enter the account name (prom) and password (prom), and press the Enter key. Switch login: prom Password:xxxx 4.
S 5 – Diagnostics/Troubleshooting Power-On Self Test Diagnostics e. Establish communications with the switch using Telnet. Enter one of the following on the command line: telnet xxx.xxx.xxx.xxx or telnet switchname f. g. where xxx.xxx.xxx.xxx is the switch IP address and switchname is the switch name associated with the IP address. A Telnet window opens prompting you for a login. Enter an account name and password. The default account name and password are (admin, password).
A 5 – Diagnostics/Troubleshooting Power-On Self Test Diagnostics 3. For a model 5602 switch, observe the air flow direction from both power supplies; otherwise continue. Are the flow directions the same? 4. Yes - Continue. No - Determine the proper air flow direction for the switch. Replace the power supply with the incorrect air flow direction with another having the correct air flow direction. Air flow direction is marked on the power supply part number label.
5 – Diagnostics/Troubleshooting Power-On Self Test Diagnostics S 5.2.2.1 E_Port Isolation A Logged-In LED error indication is often the result of E_Port isolation. An isolated E_Port is indicated by a red link in the SANsurfer Switch Manager topology display.
A 5 – Diagnostics/Troubleshooting Power-On Self Test Diagnostics 4. 5. Compare the RA_TOV and ED_TOV timeout values for all switches in the fabric using the Show Config Switch command or the Switch data tab of the SANsurfer Switch Manager topology display. Is each timeout value the same on every switch? Yes - Continue. No - Correct the timeout values on the offending switches using the Set Config Switch command or the SANsurfer Switch Manager Switch Properties dialog. Reset the port.
5 – Diagnostics/Troubleshooting Power-On Self Test Diagnostics S If the count for any of these errors exceeds the rising trigger for three consecutive sample windows, the switch generates an alarm and disables the affected port, changing its operational state to “down”.
A 5 – Diagnostics/Troubleshooting Power Supply Diagnostics 5.3 Power Supply Diagnostics A model 5602 switch power supply has a Status LED (Green) and a Fault LED (Amber) as shown in Figure 5-3. Under normal operating conditions, the Power Supply Status LED is illuminated and the Power Supply Fault LED is extinguished. Power Supply Status LED Power Supply Fault LED Figure 5-3. Model 5602 Switch Power Supply LEDs Consider the following indications: 59096-02 C Power Supply Fault LED is illuminated.
5 – Diagnostics/Troubleshooting Recovering a Switch S 5.4 Recovering a Switch A switch can become inoperable or unmanageable for the following reasons: Firmware becomes corrupt IP address is lost Switch configuration becomes corrupt Forgotten password In these specific cases, you can recover the switch using maintenance mode. Maintenance mode temporarily returns the switch IP address to 10.0.0.
A 5 – Diagnostics/Troubleshooting Recovering a Switch 5. The maintenance menu displays several recovery options. To select a switch recovery option, press the corresponding number (displayed in option: field) on the keyboard and press the Enter key.
5 – Diagnostics/Troubleshooting Recovering a Switch 5. S Select option 1 from the maintenance menu. When prompted for a file name prompt, enter the firmware image file name. Image filename: filename Unpacking ’filename’, please wait... Unpackage successful. 6. Select option 7 to reset the switch and exit maintenance mode. 5.4.3 Maintenance – Reset Network Config This option resets the network properties to the factory default values and saves them on the switch.
A 5 – Diagnostics/Troubleshooting Recovering a Switch 5.4.7 Maintenance – Remake Filesystem In the event of a loss of power, the switch configuration may become corrupt. The file system on which the configuration is stored must be re-created. This option resets the switch to the factory default values including user accounts and zoning. Refer to Table B-9 though Table B-16 for the factory default values.
5 – Diagnostics/Troubleshooting Recovering a Switch S Notes 5-16 59096-02 C
Section 6 Removal/Replacement This section describes the removal and replacement procedures for the following field replaceable units (FRU): SFP transceivers Power supplies for model 5602 switches The switch is equipped with a battery that powers the non-volatile memory. This memory stores the switch configuration. The battery is not a field replaceable unit. WARNING!! Danger of explosion if battery is incorrectly replaced.
6 – Removal/Replacement SFP Transceiver Removal and Replacement S 6.1 SFP Transceiver Removal and Replacement The SFP transceivers can be removed and replaced while the switch is operating without damaging the switch or the transceiver. However, transmission on the affected port will be interrupted until the transceiver installed. To remove a transceiver, gently press the transceiver into the port to release the tension, then pull on the release tab or lever and remove the transceiver.
A 6 – Removal/Replacement Power Supply Removal and Replacement Knurled Fasteners Figure 6-1. Power Supply Removal 1. Confirm that the Heartbeat LED is showing the normal 1 blink per second. This allows the switch to correctly report power supply status. 2. Confirm that the new power supply is compatible with the switch air flow direction. The part number label on the power supply indicates the air flow direction as shown in Figure 6-2. 3.
6 – Removal/Replacement Power Supply Removal and Replacement S Notes 6-4 59096-02 C
Appendix A Specifications This appendix contains the specifications for the SANbox 5600 Series Fibre Channel switch. Refer to Section 2 General Description for the location of all connections, switches, controls, and components. A.1 Fabric Specifications Fibre Channel Protocols ................. FC-PH Rev. 4.3 FC-PH-2 FC-PH-3 FC-AL Rev 4.6 FC-AL-2 Rev 7.0 FC-FLA FC-GS FC-GS-2 FC-GS-3 FC-FG FC-Tape FC-VI FC-SW-2 Fibre Channel Element MIB RFC 2837 Fibre Alliance MIB Version 4.
S A – Specifications Fabric Specifications Number of Fibre Channel Ports ...... Variable and can be upgraded in the following configurations: 8 1/2/4-Gbps FC ports 12 1/2/4-Gbps FC ports 16 1/2/4-Gbps FC ports 16 1/2/4-Gbps FC ports plus 4 10-Gbps FC ports Scalability........................................ Maximum 239 switches depending on configuration Maximum User Ports ...................... > 475,000 ports depending on configuration Buffer Credits..................................
A A – Specifications Maintainability A.2 Maintainability Diagnostics ..................................... Power-On Self Test (POST) tests all functional components except SFP transceivers. Port tests include online, internal, and external tests. User Interface ................................. LED indicators Field Replaceable Units.................. Power supplies (model 5602 only) A.3 Fabric Management Management Methods ....................
S A – Specifications Dimensions A.4 Dimensions Model 5600 Model 5602 Width 17” (432 mm), 19" rack 17” (432 mm), 19" rack Height 1.70” (43.2 mm) (1U) 1.70” (43.2 mm) (1U) Depth 12.0” (305 mm) 19.69” (500 mm) Weight 9 lbs (4.08 Kg) 16 lbs (7.25 Kg) A.5 Electrical Operating voltage ........................... 100 to 240 VAC; 50 to 60 Hz Power source loading (maximum) .. 1 A at 120 VAC 0.5 A at 240 VAC Heat Output (maximum) ................. 100 watts Circuit Protection .......................
A A – Specifications Environmental Altitude Operating .................................. 0 to 3048m (0 to 10,000 feet) Non-operating ........................... 0 to 15,240m (0 to 50,000 feet) Vibration IEC 68-2 Operating .................................. 5-500 Hz, random, 0.21 G rms, 10 minutes Non-operating ........................... 5-500 Hz, random, 2.09 G rms, 10 minutes Shock IEC 68-2 Operating .................................. 4 g, 11ms, 20 repetitions Non-operating .............
S A – Specifications Regulatory Certifications A.7 Regulatory Certifications Safety Standards ............................ UL60950:2000 CSA 22.2 No. 60950-00 (Canada) EN60950:2000 (EC) CB Scheme-IEC 60950:1999 Emissions Standards ...................... FCC Part 15B Class A ICES-03 Issue 3 VCCI Class A ITE CISPR 22, Class A EN 55022, Class A Voltage Fluctuations ....................... EN 61000-3-3 Harmonics....................................... EN 61000-3-2 Immunity .....................................
Appendix B Command Line Interface The command line interface (CLI) enables you to perform a variety of fabric and switch management tasks through an Ethernet or a serial port connection. This section describes the following: Logging On to a Switch User Accounts Working with Switch Configurations Commands B.
B – Command Line Interface User Accounts S B.2 User Accounts Switches come from the factory with the following user account already defined: Account name: admin Password: password Authority: Admin This user account provides full access to the switch and its configuration. After planning your fabric management needs and creating your own user accounts, consider changing the password for this account. Refer to ”Commands” on page B-6 for information about authority levels.
A B – Command Line Interface Working with Switch Configurations B.3.1 Modifying a Configuration A switch supports up to 10 configurations including the default configuration. Each switch configuration contains switch, port, port threshold alarm, and zoning configuration components. The Show Switch command displays the name of the active configuration. A configuration name can have up to 31 characters excluding the pound symbol (#), semicolon (;), and comma (,).
B – Command Line Interface Working with Switch Configurations S B.3.2 Backing up and Restoring Switch Configurations Backing up and restoring a configuration is useful to protect your work or for use as a template in configuring other switches. The Config Backup command creates a file on the switch, named configdata. This file can be used to restore a switch configuration only from the command line interface; it cannot be used to restore a switch using SANsurfer Switch Manager.
A B – Command Line Interface Working with Switch Configurations The restore operation begins with FTP to upload the configuration file from the workstation to the switch, then finishes with a Telnet session and the Config Restore command. To upload the configuration file, config_switch_169_10112003 in this case, open and FTP session with account name images and password images.
S B – Command Line Interface Commands B.4 Commands The command syntax is as follows: command keyword keyword [value] keyword [value1] [value2] The Command is followed by one or more keywords. Consider the following rules and conventions: Commands and keywords are case insensitive. Required keyword values appear in standard font: [value]. Optional values are shown in italics: [value]. Underlined portions of the keyword in the command format indicate the abbreviated form that can be used.
A B – Command Line Interface Commands Table B-2.
B – Command Line Interface Admin Command S Admin Command Opens and closes an Admin session. The Admin session provides commands that change the fabric and switch configurations. Only one Admin session can be open on the switch at any time. An inactive Admin session will time out after a period of time which can be changed using the Set Setup System command. Refer to the ”Set Setup Command” on page B-82.
A B – Command Line Interface Alias Command Alias Command Creates a named set of ports/devices. Aliases make it easier to assign a set of ports/devices to many zones. An alias can not have a zone or another alias as a member.
B – Command Line Interface Alias Command S delete [alias] Deletes the specified alias given by [alias] from the zoning database. If the alias is a member of the active zone set, the alias will not be removed from the active zone set until the active zone set is deactivated. list Displays a list of all aliases. This keyword does not require an admin session. members [alias] Displays all members of the alias given by [alias]. This keyword does not require an admin session.
A B – Command Line Interface CIM Command CIM Command Manages CIM listener and subscription configurations on the switch. Refer to the ”CIMListener Command” on page B-13 for information about creating and modifying CIM listeners. Refer to the ”CIMSubscription Command” on page B-15 for information about creating and modifying CIM subscriptions. Authority Admin session Syntax cim cancel clear edit limits save Keywords cancel Terminates the current CIM edit session without saving changes that were made.
S B – Command Line Interface CIM Command The following is an example of the CIM Limits command: SANbox #> cim limits B-12 Cim Attribute Maximum ------------- ------- MaxListeners 32 MaxSubscriptions 50 MaxSubscriptionsPerListener 6 59096-02 C
A B – Command Line Interface CIMListener Command CIMListener Command Configures CIM indication service listeners and adds subscriptions to listeners. Refer to the ”CIMSubscription Command” on page B-15 for information about configuring subscriptions. Authority Admin session and a CIM Edit session. Refer to the ”CIM Command” on page B-11 for information about opening a CIM edit session.
S B – Command Line Interface CIMListener Command edit [listener_name] Opens an editing session in which you can modify the CIM listener given by [listener_name]. Refer to Table B-3 for a description of the CIM listener configuration parameters. Examples The following is an example of the CIMListener Create command: SANbox (admin-cim) #> cimlistener create listener_1 A list of attributes with formatting and current values will follow.
A B – Command Line Interface CIMSubscription Command CIMSubscription Command Creates, edits, or removes CIM subscriptions. Authority Admin session and a CIM Edit session. Refer to the ”CIM Command” on page B-11 for information about opening a CIM edit session.
S B – Command Line Interface CIMSubscription Command edit [subscription_name] Opens an editing session in which you can modify the CIM subscription given by [subscription_name]. Refer to Table B-4 for a description of the CIM subscription configuration parameters. Examples The following is an example of the CIMSubscription Create command: SANbox (admin-cim) #> cimsubscription create subscription_1 A list of attributes with formatting and current values will follow.
A B – Command Line Interface Config Command Config Command Manages the Fibre Channel configurations on a switch. For information about setting the port and switch configurations, refer to the ”Set Config Command” on page B-64.
B – Command Line Interface Config Command S edit [config_name] Opens an edit session for the configuration given by [config_name]. If you omit [config_name], the currently active configuration is used. list Displays a list of all available configurations on the switch. This keyword does not require an admin session. restore Restores configuration settings to an out-of-band switch from a backup file named configdata, which must be first uploaded on the switch using FTP.
A B – Command Line Interface Config Command The following is an example of how to create a backup file (configdata) and download the file to the workstation.
B – Command Line Interface Create Command S Create Command Creates support files for troubleshooting switch problems, and certificates for secure communications for SANsurfer Switch Manager. Authority Admin session Syntax create certificate support Keywords certificate Creates a security certificate on the switch. The security certificate is required to establish an SSL connection with a management application such as SANsurfer Switch Manager.
A Examples B – Command Line Interface Create Command The following is an example of the Create Support command when an FTP server is available on the workstation: SANbox (admin) #> create support Log Msg:[Creating the support file - this will take several seconds] FTP the dump support file to another machine? (y/n): y Enter IP Address of remote computer: 10.20.33.
B – Command Line Interface Create Command S The following is an example of the Create Support command and how to download the support file to your workstation. When prompted to send the support file to another machine, decline, then close the Telnet session. Open an FTP session on the switch and log in with the account name images and password images. Transfer the dump_support.tgz file in binary mode with the Get command.
A B – Command Line Interface Date Command Date Command This command displays or sets the system date and time. To set the date and time the information string must be provided in this format: MMDDhhmmCCYY. The new date and time takes effect immediately. Authority Admin session except to display the date. Syntax date [MMDDhhmmCCYY] Keywords [MMDDhhmmCCYY] Specifies the date – this requires an admin session.
S B – Command Line Interface Feature Command Feature Command Adds license key features to the switch and displays the license key feature log. To order a license key contact your switch distributor or your authorized reseller. Upgrading a switch is not disruptive, nor does it require a switch reset. Authority Admin session for Add keyword only Syntax feature add [license_key] log Keywords add [license_key] Adds the feature that corresponds to the value given by [license_key].
A B – Command Line Interface Firmware Install Command Firmware Install Command Downloads firmware from a remote host to the switch, installs the firmware, then resets the switch (without a power-on self test) to activate the firmware. This is disruptive to I/O traffic. To perform a non-disruptive firmware installation, refer to the ”Image Command” on page B-38.
B – Command Line Interface Group Command S Group Command Creates groups, manages membership within the group, and manages the membership of groups in security sets. Authority Admin session and a Security Edit session. Refer to the ”Security Command” on page B-54 for information about starting a Security Edit session. The List, Members, Securitysets, and Type keywords are available without an Admin session.
A Keywords B – Command Line Interface Group Command add [group] Initiates an editing session in which to specify a group member and its attributes for the existing group given by [group]. ISL, Port, and MS member attributes are described in Table B-5, Table B-6, and Table B-7 respectively. The group name and group type attributes are read-only fields common to all three tables. Table B-5. ISL Group Member Attributes Attribute Member Worldwide name of the switch that would attach to the switch.
S B – Command Line Interface Group Command Table B-6. Port Group Member Attributes Attribute B-28 Description Member Port worldwide name for the N_Port device that would attach to the switch. A member cannot belong to more than one group. Authentication Enables (CHAP) or disables (None) authentication using the Challenge Handshake Authentication Protocol (CHAP). The default is None.
A B – Command Line Interface Group Command Table B-7. MS Group Member Attributes Attribute Description Member Port worldwide name for the N_Port device that would attach to the switch. CTAuthentication Common Transport (CT) authentication. Enables (True) or disables (False) authentication for MS group members. The default is False. Hash The hash function to use to decipher the encrypted Secret sent by the MS group member. Hash values are MD5 or SHA-1.
S B – Command Line Interface Group Command edit [group] [member] Initiates an editing session in which to change the attributes of a worldwide name given by [member] in a group given by [group]. Member attributes that can be changed are described in Table B-8: Table B-8.
A B – Command Line Interface Group Command Table B-8. Group Member Attributes (Continued) Attribute Binding (ISL Groups) Description Domain ID of the switch to which to bind the ISL group member worldwide name. This option is available only if FabricBindingEnabled is set to True using the Set Config Security command. Refer to the ”Set Config Command” on page B-64. 0 (zero) specifies no binding. list Displays a list of all groups and the security sets of which they are members.
S B – Command Line Interface Group Command Examples The following is an example of the Group Add command: SANbox (admin-security) #> group add Group_1 A list of attributes with formatting and default values will follow Enter a new value or simply press the ENTER key to accept the current value with exception of the Group Member WWN field which is mandatory. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
A B – Command Line Interface Group Command The following is an example of the Group List command: SANbox #> group list Group SecuritySet ----- ----------- group1 (ISL) alpha group2 (Port) alpha The following is an example of the Group Members command: SANbox #> group members group1 Current list of members for Group: group1 ---------------------------------10:00:00:c0:dd:00:71:ed 10:00:00:c0:dd:00:72:45 10:00:00:c0:dd:00:90:ef 10:00:00:c0:dd:00:b8:b7 59096-02 C B-33
B – Command Line Interface Hardreset Command S Hardreset Command Resets the switch and performs a power-on self test. This reset disrupts traffic, activates the pending firmware, and clears the alarm log. To save the alarm log before resetting, refer to the ”Set Log Command” on page B-76. Authority Admin session Syntax hardreset Notes To reset the switch without a power-on self test, refer to the ”Reset Command” on page B-46.
A B – Command Line Interface Help Command Help Command Displays a brief description of the specified command, its keywords, and usage. Authority None Syntax help [command] [keyword] Keywords [command] Displays a summary of the command given by [command] and its keywords. If you omit [command], the system displays all available commands. [keyword] Displays a summary of the keyword given by [keyword] belonging to the command given by [command].
S B – Command Line Interface History Command History Command Displays a numbered list of the previously entered commands from which you can re-execute selected commands. Authority None Syntax history Notes Use the History command to provide context for the ! command: Examples Enter ![command_string] to re-execute the most recent command that matches [command_string].
A B – Command Line Interface Hotreset Command Hotreset Command Resets the switch for the purpose of activating the pending firmware without disrupting traffic. This command terminates all management sessions, saves all configuration information, and clears the event log. After the pending firmware is activated, the configuration is recovered. This process takes less than 80 seconds. To save the event log to a file before resetting, refer to the ”Set Log Command” on page B-76.
B – Command Line Interface Image Command S Image Command Manages and installs switch firmware. Authority Admin session Syntax image cleanup fetch [account_name] [ip_address] [file_source] [file_destination] install list unpack [file] Keywords cleanup Removes all firmware image files from the switch. All firmware image files are removed automatically each time the switch is reset.
A Notes B – Command Line Interface Image Command To provide consistent performance throughout the fabric, ensure that all switches are running the same version of firmware. To perform a non-disruptive firmware installation and activation, do the following: 1. Connect to the switch through the Ethernet port or the serial port. 2. Move to the folder or directory on the workstation that contains the new firmware image file. 3.
S B – Command Line Interface Image Command 11. Unpack the firmware image file to install the new firmware in flash memory. SANbox (admin) $>image unpack filename 12. Wait for the unpack to complete. image unpack command result: Passed 13. A message will prompt you to reset the switch to activate the firmware. Resetting the switch is disruptive. Use the Hotreset command to attempt a non-disruptive activation.
A B – Command Line Interface Lip Command Lip Command Reinitializes the specified loop port. Authority Admin session Syntax lip [port_number] Keywords [port_number] The number of the port to be reinitialized. Ports are numbered beginning with 0.
S B – Command Line Interface Passwd Command Passwd Command Changes a user account’s password. Authority Admin account name and an admin session to change another account’s password; You can change you own password without an Admin session. Syntax passwd [account_name] Keywords [account_name] The user account name. To change the password for an account name other than your own, you must open an admin session with the account name Admin.
A B – Command Line Interface Ping Command Ping Command Initiates an attempt to communicate with another switch over an Ethernet network and reports the result. Authority None Syntax ping [ip_address] Keywords [ip_address] The IP address of the switch to query. Broadcast IP addresses, such as 255.255.255.255, are not valid. Examples The following is an example of a successful Ping command: SANbox #> ping 10.20.11.57 Ping command issued. Waiting for response...
S B – Command Line Interface Ps Command Ps Command Displays current system process information. Authority None Syntax ps Examples The following is an example of the Ps command: SANbox #> ps PID B-44 PPID %CPU TIME ELAPSED COMMAND 338 327 0.0 00:00:00 3-01:18:35 cns 339 327 0.0 00:00:01 3-01:18:35 ens 340 327 0.0 00:00:21 3-01:18:35 dlog 341 327 0.1 00:05:35 3-01:18:35 ds 342 327 0.2 00:11:29 3-01:18:35 mgmtApp 343 327 0.0 00:00:04 3-01:18:35 fc2 344 327 0.
A B – Command Line Interface Quit Command Quit Command Closes the Telnet session. Authority None Syntax quit, exit, or logout Notes You can also enter Control-D to close the Telnet session.
S B – Command Line Interface Reset Command Reset Command Resets the switch configuration parameters. If you omit the keyword, the default is Reset Switch.
A B – Command Line Interface Reset Command radius Resets the RADIUS configuration to the default values as described in Table B-14. security Clears the security database and deactivates the active security set. The security configuration value, autosave, and fabric binding remain unchanged. services Resets the switch services configuration to the default values as described in Table B-15. snmp Resets the SNMP configuration settings to the factory default values.
S B – Command Line Interface Reset Command Notes The following tables specify the various factory default settings: Enter the Show Config Switch command to display switch configuration values. Table B-9.
A B – Command Line Interface Reset Command Enter the Show Config Port command to display port configuration values. Table B-10.
S B – Command Line Interface Reset Command Enter Show Config Threshold command to display threshold alarm configuration values. Table B-11.
A B – Command Line Interface Reset Command Table B-12. Zoning Configuration Defaults Parameter Default InteropAutoSave True DefaultVisibility All DiscardInactive False Enter the Show Setup SNMP command to display SNMP configuration values. Table B-13. SNMP Configuration Defaults Parameter Default SNMPEnabled True Contact Location Description SANbox 5600 Series FC Switch Trap [1-5] Address Trap 1: 10.0.0.254; Traps 2–5: 0.0.0.
S B – Command Line Interface Reset Command Enter the Show Setup Radius command to display RADIUS configuration values. Table B-14. RADIUS Configuration Defaults Parameter Default DeviceAuthOrder Local UserAuthOrder Local TotalServers 1 DeviceAuthServer False UserAuthServer False AccountingServer False ServerIPAddress 10.0.0.1 ServerUDPPort 1812 Timeout 2 seconds Retries 0 SignPackets False Enter the Show Setup Services command to display switch service configuration values.
A B – Command Line Interface Reset Command Enter the Show Setup System command to display system configuration values. Table B-16. System Configuration Defaults Parameter Default Ethernet Network Discovery Static Ethernet Network IP Address 10.0.0.1 Ethernet Network IP Mask 255.0.0.0 Ethernet Gateway Address 10.0.0.254 Admin Timeout 30 minutes InactivityTimeout 0 LocalLogEnabled True RemotelogEnabled False RemoteLogHostAddress 10.0.0.254 NTPClientEnabled False NTPServerAddress 10.0.
B – Command Line Interface Security Command S Security Command Opens a Security Edit session in which to manage the security database on a switch. Refer to the ”Group Command” on page B-26 and the ”Securityset Command” on page B-58. Authority Admin session. The keywords Active, History, Limits, and List are available without an Admin session. Syntax security active cancel clear edit history limits list restore save Keywords active Displays the active security set, its groups, and group members.
A B – Command Line Interface Security Command edit Initiates a Security Edit session in which to make changes to the security database. A Security Edit session enables you to use the Group and Securityset commands to create, add, and delete security sets, groups, and group members. To close a Security Edit session and save changes, enter the Security Save command. To close a Security Edit session without saving changes, enter the Security Cancel command.
S B – Command Line Interface Security Command Examples The following is an example of the Security Active command: SANbox #> security active Active Security Information SecuritySet Group GroupMember ----------- ----- ----------- alpha group1 (ISL) 10:00:00:00:00:10:21:16 Authentication Chap Primary Hash MD5 Primary Secret ******** Secondary Hash SHA-1 Secondary Secret ******** Binding 0 10:00:00:00:00:10:21:17 Authentication Chap Primary Hash MD5 Primary Secret ******** Secondary
A B – Command Line Interface Security Command The following is an example of the Security Limits command: SANbox #> security limits Security Attribute Maximum Current [Name] ------------------ ------- ------- ------ MaxSecuritySets 4 1 MaxGroups 16 2 MaxTotalMembers 1000 19 MaxMembersPerGroup 1000 4 group1 15 group2 The following is an example of the Security List command: SANbox (admin-security) #> security list SB211.
B – Command Line Interface Securityset Command S Securityset Command Manages security sets in the security database. Authority Admin session and a Security Edit session. Refer to the ”Security Command” on page B-54 for information about starting a Security Edit session. The Active, Groups, and List keywords are available without an Admin session. You must close the Security Edit session before using the Activate and Deactivate keywords.
A B – Command Line Interface Securityset Command create [security_set] Creates the security set with the name given by [security_set]. A security set name must begin with a letter and be no longer than 64 characters. Valid characters are 0-9, A-Z, a-z, _, $, ^, and -. The security database supports a maximum of 4 security sets. deactivate Deactivates the active security set. Close the Security Edit session before using this keyword. delete [security_set] Deletes the security set given by [security_set].
B – Command Line Interface Securityset Command S The following is an example of the Securityset Groups command SANbox #> securityset groups alpha Current list of Groups for SecuritySet: alpha --------------------------------------group1 (ISL) group2 (Port) The following is an example of the Securityset List command SANbox #> securityset list Current list of SecuritySets ---------------------------alpha beta B-60 59096-02 C
A B – Command Line Interface Set Command Set Command Sets a variety of switch parameters. Authority Admin session for all keywords except Alarm, Beacon, and Pagebreak which are available without an Admin session. Syntax set alarm [option] beacon [state] config [option] log [option] pagebreak [state] port [option] setup [option] switch [state] timezone Keywords alarm [option] Controls the display of alarms in the session output stream or clears the alarm log.
B – Command Line Interface Set Command S log [option] Specifies the type of entries to be entered in the event log. Refer to the ”Set Log Command” on page B-76. pagebreak [state] Specifies how much information is displayed on the screen at a time according to the value given by [state]. This keyword does not require an admin session. [state] can be one of the following: on Limits the display of information to 20 lines at a time.
A B – Command Line Interface Set Command timezone Specifies the time zone for the switch and the workstation. The default is Universal Time (UTC) also known as Greenwich Mean Time (GMT). This keyword prompts you to choose a region, then a subregion to specify the time zone. Examples The following examples enables and disables the beacon: SANbox #> set beacon on Command succeeded. SANbox $> set beacon off Command succeeded.
S B – Command Line Interface Set Config Command Set Config Command Sets switch, port, port threshold alarm, security, and zoning configuration parameters. The changes you make with this command are not retained when you reset or power cycle the switch unless you save them using the Config Save command. Refer to the ”Config Command” on page B-17.
A B – Command Line Interface Set Config Command Table B-18. Set Config Port Parameters (Continued) Parameter LinkSpeed PortType 59096-02 C Description Transmission speed: 1/2/4-Gbps Ports: 1-Gbps, 2-Gbps, 4-Gbps, or Auto. The default is Auto. 10-Gbps Ports: 10-Gbps Port type: 1/2/4-Gbps Ports: GL, G, F, FL, Donor. The default is GL. 10-Gbps Ports: G SymbolicPortName Descriptive name for the port. The name can be up to 32 characters excluding #, semicolon (;), and comma (,).
S B – Command Line Interface Set Config Command Table B-18. Set Config Port Parameters (Continued) Parameter AutoPerfTuning B-66 Description Automatic performance tuning for FL_Ports only. The default is True. If AutoPerfTuning is enabled (True) and the port is an FL_Port, MFSEnable is automatically enabled. LCFEnable and VIEnable are overridden to False. If AutoPerfTuning is disabled (False), MFSEnable, LCFEnable, and VIEnable retain their original values.
A B – Command Line Interface Set Config Command Table B-18. Set Config Port Parameters (Continued) Parameter Description PDISCPingEnable (1/2/4-Gbps ports only) Enables (True) or disables (False) the transmission of ping messages from the switch to all devices on a loop port. The default is True. security Initiates an editing session in which to change the security settings. The system displays each parameter one line at a time and prompts you for a value.
S B – Command Line Interface Set Config Command Table B-20. Set Config Switch Parameters (Continued) Parameter B-68 Description InbandEnabled Inband management. Enables (True) or disables (False) the ability to manage the switch over an ISL. The default is True. FDMIEnabled Fabric Device Monitoring Interface. Enables (True) or disables (False) the monitoring of target and initiator device information. The default is True. FDMIEntries The number of device entries to maintain in the FDMI database.
A B – Command Line Interface Set Config Command threshold Initiates a configuration session by which to generate and log alarms for selected events. The system displays each event, its triggers, and sampling window one line at a time and prompts you for a value. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. These parameters must be saved in a configuration and activated before they will take effect.
S B – Command Line Interface Set Config Command zoning Initiates an editing session in which to change switch zoning attributes. The system displays each parameter one line at a time and prompts you for a value. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. Table B-22.
A Examples B – Command Line Interface Set Config Command The following is an example of the Set Config Port command: SANbox #> admin start SANbox (admin) #> config edit SANbox (admin-config) #> set config port 1 A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
S B – Command Line Interface Set Config Command The following is an example of the Set Config Port command for a 10-Gbps port: SANbox #> admin start SANbox (admin) #> config edit SANbox (admin-config) #> set config port 16 A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
A B – Command Line Interface Set Config Command The following is an example of the Set Config Security command: SANbox #> admin start SANbox (admin) #> config edit SANbox (admin-config) #> set config security A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
S B – Command Line Interface Set Config Command The following is an example of the Set Config Threshold command: SANbox #> admin start SANbox (admin) #> config edit SANbox (admin-config) #> set config threshold A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
A B – Command Line Interface Set Config Command The following is an example of the Set Config Zoning command. SANbox #> admin start SANbox (admin) #> config edit SANbox (admin-config) #> set config zoning A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
B – Command Line Interface Set Log Command S Set Log Command Specifies the events to record in the event log and display on the screen. You determine what events to record in the switch event log using the Component, Level, and Port keywords. You determine what events are automatically displayed on the screen using the Display keyword. Alarms are always displayed on the screen.
A B – Command Line Interface Set Log Command Eport Monitors all E_Ports. Mgmtserver Monitors management server status. Nameserver Monitors name server status. None Monitor none of the component events. Other Monitors other miscellaneous events. Port Monitors all port events. SNMP Monitors all SNMP events. Switch Monitors switch management events. Zoning Monitors zoning conflict events.
B – Command Line Interface Set Log Command S None Specifies no severity levels for display on the screen. level [filter] Specifies the severity level given by [filter] to use in monitoring and logging events for the specified components or ports. [filter] can be one of the following values: Critical Monitors critical events. The critical level describes events that are generally disruptive to the administration or operation of the fabric, but require no action. Warn Monitors warning and critical events.
A B – Command Line Interface Set Log Command save Saves the log settings for the component, severity level, port, and display level. These settings remain in effect after a switch reset. The log settings can be viewed using the Show Log Settings command. To export log entries to a file, use the Set Log Archive command. start Starts the logging of events based on the Port, Component, and Level keywords assigned to the current configuration. The logging continues until you enter the Set Log Stop command.
B – Command Line Interface Set Port Command S Set Port Command Sets port state and speed for the specified port temporarily until the next switch reset or new configuration activation. This command also clears port counters. Authority Admin session except for the Clear keyword. Syntax set port [port_number] bypass [alpa] clear enable speed [transmission_speed] state [state] Keywords [port_number] Specifies the port. Ports are numbered beginning with 0.
A B – Command Line Interface Set Port Command Auto The port speed is automatically detected. This applies only to ports 0–15. state [state] Specifies one of the following administrative states for the specified port: Online Places the port online. This activates and prepares the port to send data. Offline Places the port offline. This prevents the port from receiving signal and accepting a device login. Diagnostics Prepares the port for testing.
S B – Command Line Interface Set Setup Command Set Setup Command Manages configuration settings for Remote Authentication Dial-In User Service (RADIUS) servers, switch services, SNMP, and system configurations. Authority Admin session Syntax set setup radius services snmp system Keywords radius Prompts you in a line-by-line fashion to configure RADIUS servers for user account and device authentication. Table B-23 describes the RADIUS server configuration fields. Table B-23.
A B – Command Line Interface Set Setup Command Table B-23. RADIUS Service Settings (Continued) Entry 59096-02 C Description ServerUDPPort User Datagram Protocol (UDP) port number on the RADIUS server. The default is 1812. DeviceAuthServer Enable (True) or disable (False) this server for device authentication. The default is False. UserAuthServer Enable (True) or disable (False) this server for user account authentication.
S B – Command Line Interface Set Setup Command services Prompts you in a line-by-line fashion to enable or disable switch services. Table B-24 describes the switch service parameters. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. NOTE: Use caution when disabling TelnetEnabled and GUIMgmtEnabled; it is possible to disable all Ethernet access to the switch. Table B-24.
A B – Command Line Interface Set Setup Command Table B-24. Switch Services Settings (Continued) Entry Description EmbeddedGUIEnabled Enables (True) or disables (False) the SANsurfer Switch Manager web applet. The web applet enables you to point at a switch with an internet browser and run SANsurfer Switch Manager through the browser. This parameter is the master control for the Set Setup System command parameter, EmbeddedGUIEnabled. The default is True.
S B – Command Line Interface Set Setup Command snmp Prompts you in a line-by-line fashion to change SNMP configuration settings. Table B-25 describes the SNMP fields. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. Table B-25. SNMP Configuration Settings Entry B-86 Description SNMPEnabled Enables (True) or disables (False) SNMP on the switch. The default is True.
A B – Command Line Interface Set Setup Command Table B-25. SNMP Configuration Settings (Continued) Entry Description TrapCommunity Trap community password that authorizes an SNMP agent to receive traps. This is a write-only field. The value on the switch and the SNMP management server must be the same. The trap community password can be up to 32 characters excluding #, semicolon (;), and comma (,). The default is “public”.
S B – Command Line Interface Set Setup Command Table B-26. System Configuration Settings (Continued) Entry B-88 Description LocalLogEnabled Enables (True) or disables (False) the saving of log information on the switch. The default is True. RemoteLogEnabled Enables (True) or disables (False) the recording of the switch event log on a remote host that supports the syslog protocol. The default is False.
A Examples B – Command Line Interface Set Setup Command The following is an example of the Set Setup RADIUS command: SANbox (admin) #> set setup radius A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the attributes for the server being processed, press 'q' or 'Q' and the ENTER key to do so.
S B – Command Line Interface Set Setup Command The following is an example of the Set Setup SNMP command: SANbox #> admin start SANbox (admin) #> set setup snmp A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
A B – Command Line Interface Set Setup Command The following is an example of the Set Setup System command: SANbox (admin) #> set setup system A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
B – Command Line Interface Show Command S Show Command Displays fabric, switch, and port operational information.
A B – Command Line Interface Show Command alarm [option] Displays the alarm log and session display setting. If you omit [option], the command displays the last 200 alarm entries. The alarm log is cleared when the switch is reset or power cycled. [option] has the following value: setting Displays the status of the parameter that controls the display of alarms in the session output stream. This parameter is set using the Set Alarm command.
S B – Command Line Interface Show Command fdmi [port_wwn] Displays detailed information about the device host bus adapter given by [port_wwn]. If you omit [port_wwn], the command displays a summary of host bus adapter information for all attached devices in the fabric. Illegal characters in the display appear as question marks (?). interface Displays the status of the active network interfaces. log [option] Displays log entries. Refer to the ”Show Log Command” on page B-111.
A B – Command Line Interface Show Command pagebreak Displays the current pagebreak setting. The pagebreak setting limits the display of information to 20 lines (On) or allows the continuous display of information without a break (Off). perf [option] Displays performance information for all ports. Refer to the ”Show Perf Command” on page B-115. port [port_number] Displays operational information for the port given by [port_number]. Ports are numbered beginning with 0.
S B – Command Line Interface Show Command Table B-27. Show Port Parameters (Continued) Entry B-96 Description InvalidDestAddr Invalid destination address detected. LIP_AL_PD_ALPS Number of F7, AL_PS LIPs, or AL_PD (vendor specific) resets, performed. LIP_F7_AL_PS This LIP is used to reinitialize the loop. An L_Port, identified by AL_PS, may have noticed a performance degradation and is trying to restore the loop.
A B – Command Line Interface Show Command Table B-27. Show Port Parameters (Continued) Entry Description TotalLinkResets Total number of link reset primitives. TotalOfflineSeq Total number of Offline Sequences issued and received by this port. TotalRxFrames Total number of frames received by this port. TotalRxWords Total number of words received by this port. TotalTxFrames Total number of frames issued by this port. TotalTxWords Total number of words issued by this port.
S B – Command Line Interface Show Command Securityset (Active, List) Show (About, Alarm, Backtrace, Chassis, Config Port, Config Security, Config Switch, Config Threshold, Dev, Dev Settings, Domains, Donor, Fabric, Log, Log Archive, Log Settings, Lsdb, Mem, Ns, Perf, Port, Setup Mfg, Setup Snmp, Setup System, Steering, Switch, Topology, Users) Uptime User Accounts Whoami Zoneset (Active, List) Zoning (History, Limits, List) switch Displays switch operational information.
A B – Command Line Interface Show Command Table B-28. Switch Operational Parameters (Continued) Parameter Description PendingImageVersion - build date Firmware image version and build date that is pending. This image will become active at the next reset or power cycle. ActiveConfiguration Name of the switch configuration that is in use. AdminState Switch administrative state AdminModeActive Admin session status BeaconOnStatus Beacon status as set by the Set Beacon command.
S B – Command Line Interface Show Command Examples The following is an example of the Show Chassis command: SANbox #> show chassis Chassis Information ------------------BoardTemp (1) - Degrees Celsius 36 FanStatus (1) Good FanStatus (2) Good FanDirection (1) BackToFront FanDirection (2) BackToFront PowerSupplyStatus (1) Good PowerSupplyStatus (2) Good HeartBeatCode 1 HeartBeatStatus Normal The following is an example of the Show Domains command: SANbox #> show domains Principal switch i
A B – Command Line Interface Show Command The following is an example of the Show FDMI WWN command: SANbox #> show fdmi 21:00:00:e0:8b:09:3b:17 FDMI Information ---------------Manufacturer QLogic Corporation SerialNumber [04202 Model QLA2342 ModelDescription QLogic QLA2342 PCI Fibre Channel Adapter PortID 610000 NodeWWN 20:00:00:e0:8b:07:aa:bc HardwareVersion FC5010409-10 DriverVersion 8.2.3.10 Beta 2 (W2K VI) OptionRomVersion 1.21 FirmwareVersion 03.02.13. OperatingSystem SunOS 5.
S B – Command Line Interface Show Command The following is an example of the Show NS [domain_ID] command: SANbox #> show ns 18 Seq Domain No ID --- -----1 Port ID Port Type COS PortWWN NodeWWN ------ ---- --- ------- ------- 18 (0x12) 120700 N 3 21:00:00:e0:8b:07:a7:bc 20:00:00:e0:8b:07:a7:bc The following is an example of the Show NS [port_ID] command: SANbox #> show ns 1301e1 Port ID: 1301e1 -------PortType NL PortWWN 21:00:00:20:37:73:13:69 SymbolicPortName NodeWWN 20:00:00:20:37:73:13:
A B – Command Line Interface Show Command The following is an example of the Show Port command: SANbox #> show port 1 Port Number: 1 ------------ 59096-02 C AdminState Online OperationalState Online AsicNumber 0 PerfTuningMode Normal AsicPort 1 PortID 0e0800 ConfigType GL PortWWN 20:08:00:c0:dd:03:d5:94 DiagStatus Passed RunningType E EpConnState Connected MediaPartNumber PL-XPL-VC-SG3-22 EpIsoReason NotApplicable MediaRevision 1 IOStreamGuard Disabled MediaType 200-M5-SN-I
S B – Command Line Interface Show Command The following is an example of the Show Switch command: SANbox #> show switch Switch Information -----------------SymbolicName sw .108 SwitchWWN 100000c0dd00bc56 SwitchType SANbox 5600 Series BootVersion Vx.x.x.x-0 (day month date time year) CreditPool 0 DomainID 19 (0x13) FirstPortAddress 130000 FlashSize - MBytes 128 LogLevel Critical MaxPorts 20 NumberOfResets 15 ReasonForLastReset PowerUp ActiveImageVersion - build date Vx.x.x.
A B – Command Line Interface Show Command The following is an example of the Show Topology command for port 1: SANbox #> show topology 1 Local Link Information ---------------------PortNumber 1 PortID 650100 PortWWN 20:01:00:c0:dd:00:91:11 PortType F Remote Link Information ----------------------Device 0 NodeWWN 50:80:02:00:00:06:d5:38 PortType NL Description (NULL) IPAddress 0.0.0.0 Device 1 NodeWWN 20:00:00:20:37:2b:08:c9 PortType NL Description (NULL) IPAddress 0.0.0.
S B – Command Line Interface Show Command The following is an example of the Show Version command: SANbox #> show version ***************************************************** * * * Command Line Interface SHell (CLISH) * * * ***************************************************** B-106 SystemDescription SANbox 5600 Series FC Switch Eth0NetworkAddress 10.20.11.
A B – Command Line Interface Show Config Command Show Config Command Displays switch, port, alarm threshold, security, and zoning for the current configuration. Authority None Syntax show config port [port_number] security switch threshold zoning Keywords port [port_number] Displays configuration parameters for the port number given by [port_number]. Ports are numbered beginning with 0. If [port_number] is omitted, all ports are specified.
S B – Command Line Interface Show Config Command Examples The following is an example of the Show Config Port command: SANbox #> show config port 3 Port Number: 3 -----------AdminState Offline LinkSpeed Auto PortType GL SymbolicName Port3 ALFairness False DeviceScanEnabled True ForceOfflineRSCN False ARB_FF False InteropCredit 0 ExtCredit 0 FANEnabled True AutoPerfTuning False LCFEnabled False MFSEnabled True MSEnabled True NoClose False IOStreamGuard Disabled VIEnabled
A B – Command Line Interface Show Config Command The following is an example of the Show Config Switch command: SANbox #> show config switch Configuration Name: default ------------------Switch Configuration Information -------------------------------- 59096-02 C AdminState Online BroadcastEnabled False InbandEnabled True FDMIEnabled False FDMIEntries 10 DomainID 19 (0x13) DomainIDLock True SymbolicName sw108 R_A_TOV 10000 E_D_TOV 2000 PrincipalPriority 254 ConfigDescription Defau
S B – Command Line Interface Show Config Command The following is an example of the Show Config Threshold command: SANbox #> show config threshold Configuration Name: default -----------Threshold Configuration Information ----------------------------------ThresholdMonitoringEnabled False CRCErrorsMonitoringEnabled True RisingTrigger 25 FallingTrigger 1 SampleWindow 10 DecodeErrorsMonitoringEnabled True RisingTrigger 25 FallingTrigger 0 SampleWindow 10 ISLMonitoringEnabled True RisingTrig
A B – Command Line Interface Show Log Command Show Log Command Displays the contents of the log or the parameters used to create and display entries in the log. The log contains a maximum of 1200 entries. When the log reaches its entry capacity, subsequent entries overwrite the existing entries, beginning with the oldest.
B – Command Line Interface Show Log Command S Other Monitors other miscellaneous events. Port Monitors all port events SNMP SNMP events. Switch Monitors switch management events. Zoning Monitors zoning conflict events. display [filter] Displays log events on the screen according to the component or severity level filter given by [filter]. [filter] can be one of the following: Info Displays all informative events. Warning Displays all warning events. Critical Displays all critical events.
A B – Command Line Interface Show Log Command Switch Displays all events related to switch management. Zoning Displays all events related to zoning. level Displays the event severity level logging setting and the display level setting. options Displays the options that are available for configuring event logging and automatic display to the screen. Refer to the for information about how to configure event logging and display level. port Displays the ports being monitored for events.
B – Command Line Interface Show Log Command S The following is an example of the Show Log command: SANbox #> show log [327][day month date time year][I][Eport Port:0/8][Eport State= E_A0_GET_DOMAIN_ID] [328][day month date time year][I][Eport Port: 0/8][FSPF PortUp state=0] [329][day month date time year][I][Eport Port: 0/8][Sending init hello] [330][day month date time year][I][Eport Port: 0/8][Processing EFP, oxid= 0x8] [331][day month date time year][I][Eport Port: 0/8][Eport State = E_A2_IDLE] [332][d
A B – Command Line Interface Show Perf Command Show Perf Command Displays port performance in frames/second and bytes/second. If you omit the keyword, the command displays data transmitted (out), data received (in), and total data transmitted and received in frames/second and bytes per second.
S B – Command Line Interface Show Perf Command outframe [port_number] Displays continuous performance data in frames/second transmitted for the port group (0–15 or 16–19) that includes [port_number]. If you omit [port_number], ports 0–15 are displayed. Type “q” and press the Enter key to stop the display. errors [port_number] Displays continuous error counts for the port group (0–15 or 16–19) that includes [port_number]. If you omit [port_number], ports 0–15 are displayed.
A B – Command Line Interface Show Perf Command The following is an example of the Show Perf Byte command: SANbox #> show perf byte Displaying bytes/sec (total)...
S B – Command Line Interface Show Setup Command Show Setup Command Displays the current SNMP and system settings. Authority None Syntax show setup mfg radius services snmp system Keywords mfg Displays manufacturing information about the switch. radius Displays RADIUS server information. services Displays switch service status information. snmp Displays the current SNMP settings. system Displays the current system settings.
A B – Command Line Interface Show Setup Command The following is an example of the Show Setup Services command: SANbox #> show setup services System Services ----------------------------TelnetEnabled True SSHEnabled False GUIMgmtEnabled True SSLMgmtEnabled False EmbeddedGUIEnabled True SNMPEnabled True NTPEnabled True CIMEnabled True FTPEnabled True ManagementServerEnabled True The following is an example of the Show Setup RADIUS command: SANbox #> show setup radius Radius Information
S B – Command Line Interface Show Setup Command The following is an example of the Show Setup Snmp command: SANbox #> show setup snmp SNMP Information ---------------- B-120 SNMPEnabled True Contact Location N_107 System Test Lab Description SANbox 5602 FC Switch Trap1Address 10.0.0.254 Trap1Port 162 Trap1Severity warning Trap1Version 2 Trap1Enabled False Trap2Address 0.0.0.
A B – Command Line Interface Show Setup Command The following is an example of the Show Setup System command: SANbox #> show setup system System Information ------------------ 59096-02 C Eth0NetworkDiscovery Static Eth0NetworkAddress 10.20.11.32 Eth0NetworkMask 255.255.252.0 Eth0GatewayAddress 10.20.8.254 AdminTimeout 30 InactivityTimeout 0 LocalLogEnabled True RemoteLogEnabled False RemoteLogHostAddress 10.0.0.254 NTPClientEnabled True NTPServerAddress 51.68.85.
B – Command Line Interface Shutdown Command S Shutdown Command Terminates all data transfers on the switch at convenient points and closes the Telnet session. Always power cycle the switch after entering this command. Authority Admin session Syntax shutdown Notes Always use this command to perform an orderly shut down before removing power from the switch. When the shutdown is complete, the Heartbeat LED is extinguished.
A B – Command Line Interface Test Command Test Command Tests ports using internal (SerDes level), external (transceiver), and online loopback tests. Internal and external tests require that the port be placed in diagnostic mode. Refer to the ”Set Command” on page B-61 for information about changing the port administrative state. While the test is running, the remaining ports on the switch remain fully operational.
S B – Command Line Interface Test Command cancel Cancels the online test in progress. status Displays the status of a test in progress, or if there is no test in progress, the status of the test that was executed last. Examples To run an internal or external port test, do the following: 1. To start an admin session, enter the following command and press the Enter key. admin start 2. Place the port in Diagnostics mode, enter the following command (x = port number) and press the Enter key.
A B – Command Line Interface Test Command The online loopback (node-to-node) test requires that port be online and connected to a remote device. To run the online loopback test, do the following: 1. To start an admin session, enter the following command and press the Enter key. admin start 2. To run the online loopback test, enter the following command and press the Enter key. test port x online 3. A series of test parameters are displayed on the screen.
S B – Command Line Interface Uptime Command Uptime Command Displays the elapsed up time since the switch was last reset and reset method. A hot reset or non-disruptive firmware activation does not reset the elapsed up time reported by this command.
A B – Command Line Interface User Command User Command Administers and displays user accounts. Authority Admin account name and an Admin session. The Accounts and List keywords are available to all account names without an Admin session. Syntax user accounts add delete [account_name] edit list Keywords accounts Displays all user accounts that exist on the switch. This keyword is available to all account names without an Admin session. add Add a user account to the switch.
S B – Command Line Interface User Command Notes Authority level or password changes that you make to an account that is currently logged in do not take effect until that account logs in again.
A B – Command Line Interface User Command The following is an example of the User Delete command: SANbox (admin) #> user del user3 The user account will be deleted. Please confirm (y/n): [n] y The following is an example of the User List command: SANbox (admin) #> user list 59096-02 C User Ethernet Addr-Port ---- ------------------ Logged in Since --------------- admin@OB-session1 10.20.68.108-1031 day month date time year admin@OB-session2 10.20.68.
S B – Command Line Interface Whoami Command Whoami Command Displays the account name, session number, and switch domain ID for the Telnet session.
A B – Command Line Interface Zone Command Zone Command Manages zones and zone membership on a switch. Authority Admin session and a Zoning Edit session. Refer to the ”Zoning Command” on page B-138 for information about starting a Zoning Edit session. The List, Members, and Zonesets keywords are available without an Admin session.
B – Command Line Interface Zone Command S delete [zone] Deletes the specified zone given by [zone] from the zoning database. If the zone is a component of the active zone set, the zone will not be removed from the active zone set until the active zone set is deactivated. list Displays a list of all zones and the zone sets of which they are components. This keyword does not require an Admin session. members [zone] Displays all members of the zone given by [zone].
A Examples B – Command Line Interface Zone Command The following is an example of the Zone List command: SANbox #> zone list Zone ZoneSet ------------------wwn_b0241f zone_set_1 wwn_23bd31 zone_set_1 wwn_221416 zone_set_1 wwn_2215c3 zone_set_1 wwn_0160ed zone_set_1 wwn_c001b0 zone_set_1 wwn_401248 zone_set_1 wwn_02402f zone_set_1 wwn_22412f zone_set_1 The following is an example of the Zone Members command: SANbox #> zone members wwn_b0241f Current List of Members for Zone: wwn_b0241f -----------------
B – Command Line Interface Zone Command S The following is an example of the Zone Zonesets command: SANbox #> zone zonesets zone1 Current List of ZoneSets for Zone: zone1 ---------------------------------zone_set_1 B-134 59096-02 C
A B – Command Line Interface Zoneset Command Zoneset Command Manages zone sets and component zones across the fabric. Authority Admin session and a Zoning Edit session. Refer to the ”Zoning Command” on page B-138 for information about starting a Zoning Edit session. The Active, List, and Zones keywords are available without an Admin session. You must close the Zoning Edit session before using the Activate and Deactivate keywords.
S B – Command Line Interface Zoneset Command deactivate Deactivates the active zone set. Close the Zoning Edit session before using this keyword. delete [zone_set] Deletes the zone set given by [zone_set]. If the specified zone set is active, the command is suspended until the zone set is deactivated. list Displays a list of all zone sets. This keyword does not require an Admin session. remove [zone_set] [zone_list] Removes a list of zones given by [zone_list] from the zone set given by [zone_set].
A B – Command Line Interface Zoneset Command The following is an example of the Zoneset Zones command: SANbox #> zoneset zones ssss Current List of Zones for ZoneSet: ssss ---------------------------------zone1 zone2 zone3 59096-02 C B-137
B – Command Line Interface Zoning Command S Zoning Command Opens a Zoning Edit session in which to create and manage zone sets and zones. Refer to the ”Zone Command” on page B-131 and the ”Zoneset Command” on page B-135. Authority Admin session except for the Active, History, Limits, and List keywords. The Clear keyword also requires a zoning edit session.
A B – Command Line Interface Zoning Command history Displays a history of zoning modifications. This keyword does not require an Admin session. History information includes the following: Time of the most recent zone set activation or deactivation and the user who performed it Time of the most recent modifications to the zoning database and the user who made them.
S B – Command Line Interface Zoning Command save Saves changes made during the current Zoning Edit session. The system informs you that the zone set must be activated to implement any changes. This does not apply if you entered the Zoning Clear command during the Zoning Edit session. Examples The following is an example of the Zoning Edit command: SANbox #> admin start SANbox (admin) #> zoning edit SANbox (admin-zoning) #> . . SANbox (admin-zoning) #> zoning cancel Zoning edit mode will be canceled.
A B – Command Line Interface Zoning Command The following is an example of the Zoning List command: SANbox #> zoning list Active ZoneSet Information ZoneSet Zone ZoneMember -------------------------------wwn wwn_b0241f 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 21:00:00:e0:8b:02:41:2f wwn_23bd31 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:23:bd:31 wwn_221416 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:14:16 wwn_2215c3 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:
B – Command Line Interface Zoning Command S Notes B-142 59096-02 C
Glossary Access Control List Zone Access Control List zoning divides the fabric for purposes of controlling discovery and inbound traffic. Arbitrated Loop A Fibre Channel topology where ports use arbitration to establish a point-to-point circuit. Active Zone Set The zone set that defines the current zoning for the fabric. Arbitrated Loop Physical Address (AL_PA) A unique one-byte value assigned during loop initialization to each NL_Port on a loop.
S SANbox 5600 Series Fibre Channel Switch Installation Guide Class 2 Service A service which multiplexes frames at frame boundaries to or from one or more N_Ports wit h acknowledgment provided. Chassis Hop A measure of fabric latency represented by the ISL that any frame crosses when travelling from one switch to another. A frame that travels from one switch to another over an ISL experiences one chassis hop.
A Flash Memory Memory on the switch that contains the chassis control firmware. Frame Data unit consisting of a start-of-frame (SOF) delimiter, header, data payload, CRC, and an end-of-frame (EOF) delimiter. SANbox 5600 Series Fibre Channel Switch Installation Guide Input Power LED A chassis LED that indicates that the switch logic circuitry is receiving proper DC voltages. Inter-Switch Link The connection between two switches using E_Ports.
S SANbox 5600 Series Fibre Channel Switch Installation Guide MIB Management Information Base Multistage Topology A fabric in which two or more edge switches connect to one or more core switches. Network Time Protocol A network protocol that enables a client to synchronize its time with a server. NL_Port Node Loop Port. A Fibre Channel device port that supports arbitrated loop protocol.
A SANbox 5600 Series Fibre Channel Switch Installation Guide User Account Security A component of fabric security that provides for the administration and authentication of account names, passwords, expiration dates, and authority level. VCCI Voluntary Control Council for Interference Voluntary Control Council for Interference A consortium of Japanese electronics industry associations that have established voluntary standards for controlling electromagnetic interference (EMI).
SANbox 5600 Series Fibre Channel Switch Installation Guide S Notes Glossary-6 59096-02 C
Index Numerics 1/2/4-Gbps ports 2-5, 2-7 10/100 Base-T straight cable 4-8 10-Gbps port 2-5 A Access Control List zone 3-3 account name display B-127, B-130 factory B-2 ftp 5-5 maintenance mode 5-12 Activity LED 2-7, 2-8 Admin account name B-6 authority B-6 Admin command B-8 Admin session timeout B-87 administrative state port B-81 switch B-62 air flow A-5 alarm configuration B-69 configuration defaults B-50 configuration display B-107 description B-79 log B-61, B-93 alias add members B-9 copy B-9 create B-
S SANbox 5600 Series Fibre Channel Switch Installation Guide command line interface 2-12, B-1 command syntax B-6 commands B-6 Common Information Model configure B-11 display listener B-93 display subscription B-93 listener B-13 service 3-14, B-85 subscription B-15 Config command B-17 configuration activate B-17 backup B-17 copy B-17 delete B-17 edit B-18 file 5-5 file system error 2-3, 5-4, 5-6 list B-18 remove 5-14 reset B-46 restore B-18 restore default 5-14 save B-18 connection Secure Socket Layer B-20
A event logging by component B-76, B-111 by port B-78, B-113 by severity level B-113 display B-111 restore defaults B-78 save settings B-79 settings B-113 severity level B-78 start B-79 stop B-79 extended credits 3-4 external test B-123 F F_Port 2-7 fabric management 3-27, A-3 management switch 2-8 management workstation 4-1 point-to-point bandwidth A-2 port 2-7 security 3-14 Fabric Device Management Interface B-94 factory defaults 5-14, B-46 Feature command B-24 fiber optic cable 3-1 Fibre Channel ports 2
S SANbox 5600 Series Fibre Channel Switch Installation Guide H Hardreset command B-34 harmonics A-6 HBA - See Host Bus Adapter Heartbeat LED 2-4, 5-3 heat output A-4 Help command B-35 History command B-36 host authentication example 3-23 host bus adapter 3-1, B-94 Hotreset command B-37 humidity 4-2, A-4 HyperTerminal application 4-10 I I/O Stream Guard B-66 Image command B-38 immunity A-6 inband management 3-13 indication service listener B-13 Input Power LED 5-2 installation 4-2 internal firmware failur
A marking A-6 mask address B-87 MD5 authentication B-28 media type A-2 memory activity B-94 flash 2-3 workstation 4-1 mesh topology 3-11 minicom 4-10 Multi-Frame Sequence bundling B-66 multiple chassis fabrics 3-6 Multistage topology 3-12 N SANbox 5600 Series Fibre Channel Switch Installation Guide P page break B-62 Passwd command B-42 password change B-42 factory B-2 file reset 5-14 maintenance mode 5-12 restore default 5-14 switch B-42 performance device 3-6 switch 3-4 tuning B-66 Ping command B-43 pla
S SANbox 5600 Series Fibre Channel Switch Installation Guide port 1/2/4-Gbps 2-5 10-Gbps 2-5 administrative state B-81 buffer credits 3-4 characteristics A-1 configuration B-64 configuration defaults B-49 configuration display B-107 counters B-80 diagnostics 5-7 Ethernet 2-8 external test B-123 fabric 2-7 Fibre Channel 2-5 generic 2-7 group B-29 initialize B-46 LEDs 2-6 loopback test B-123 maximum number of ports/users A-2 number of A-2 online test B-123 operational information B-95 performance B-95, B-11
A SANsurfer Switch Manager API 2-12 description 2-11 Linux install 4-12 Mac OS X install 4-12 Solaris install 4-12 start 4-18 web applet 2-11, B-85, B-88 Windows install 4-11 scalability A-2 secret B-28 Secure Shell description 3-15 service 3-13, B-84 Secure Socket Layer certificate B-20 service 3-13, B-84 switch time B-23 security certificate 3-15 configuration B-67 configuration defaults B-53 configuration display B-107 connection 3-15 device 3-16 fabric 3-14 user account 3-26 Security command B-54 securi
S SANbox 5600 Series Fibre Channel Switch Installation Guide stacking 3-6, 3-8 steering B-97 subscription create B-15 delete B-15 display B-93 support file B-20 switch administrative state B-62 configuration 4-23, B-67 configuration defaults B-48 configuration display B-107 hard reset B-34 log B-88 management 2-11 management service 3-13, B-84 manufacturer information B-118 operational information B-98 power up 4-22 recovery 5-12 reset 2-3, 5-15, B-126 reset without POST B-47 services 3-13, B-47, B-84, B-
A W web applet B-85 description 2-11 enable B-88 service 3-13 Whoami command B-130 workstation configuration 4-9 connect 4-8 IP address 4-9 requirements 4-1 worldwide name 3-2 WWN - See Worldwide Name Z zone access control list 3-3 add member port B-131 conflict 5-9 copy B-131 create B-131 definition 3-2 delete B-132 delete member port B-132 list B-132 list members B-132 name server 3-3 rename B-132 type B-132 Zone command B-131 59096-02 C SANbox 5600 Series Fibre Channel Switch Installation Guide zone
SANbox 5600 Series Fibre Channel Switch Installation Guide S Notes Index-10 59096-02 C
