Installation guide

ManualsBrandsQlogic ManualsComputer equipmentiSR6152

ISR651103-00 C

iSR6152

Intelligent Storage Router

Installation Guide

Summary of content (122 pages)

PAGE 1
iSR6152 Intelligent Storage Router Installation Guide ISR651103-00 C
PAGE 2
iSR6152 Intelligent Storage Router Installation Guide Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for illustrative purposes only.
PAGE 3
Table of Contents Preface Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . What’s in This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Documentation Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Communications Statements . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
iSR6152 Intelligent Storage Router Installation Guide Chassis LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input Power LED (Green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heartbeat LED (Green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Fault LED (Amber) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chassis Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 5
iSR6152 Intelligent Storage Router Installation Guide Installing the iSR6152 Router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pre-Installation Check List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing the Transceivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting the Management Workstation to the Router. . . . . . . . .
PAGE 6
iSR6152 Intelligent Storage Router Installation Guide Management Information Base (MIB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network Port Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fibre Channel Port Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensor Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 7
iSR6152 Intelligent Storage Router Installation Guide List of Figures Figure Page 1-1 iSR6152 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1-2 Chassis LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 1-3 Chassis Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 1-4 Fibre Channel Ports . . . . . . . . . . . .
PAGE 8
iSR6152 Intelligent Storage Router Installation Guide viii ISR651103-00 C
PAGE 9
Preface This guide describes the features and installation of the QLogic iSR6152 Intelligent Storage Router (iSR6152), also referred to as the iSR6152 router or simply router. Intended Audience This guide is for users who are responsible for installing, managing, and servicing the iSR6152 router and the storage area network (SAN) equipment to which it is attached.
PAGE 10
Preface Related Materials  Chapter 5 Removal and Replacement provides procedures for removing and replacing the field replaceable units (FRU): SFP transceivers and iSR6152 routers.  Appendix A Simple Network Management Protocol (SNMP) provides reference material for the simple network management protocol (SNMP) protocol, which you can use to manage the iSR6152 router using a third-party SNMP management application.
PAGE 11
Preface Documentation Conventions  ANSI SCSI – SCSI-3 Architecture Model (SAM), X3T10/994D/Rev 18, SCSI-3 Controller Command Set, X3T10/Project 1047D/Rev 6c. IEEE – 802.1Q Virtual LAN (VLAN), 802.1p Priority of Service, 802.3x Flow Control, 802.3ad Link Aggregation  SCSI-3 Fibre Channel Protocol (SCSI-FCP), X3.269:1996  Fibre Channel Physical and Signaling Interface (FC-PH), X3.230:199  Fibre Channel 2nd Generation (FC-PH-2), X3.
PAGE 12
Preface Communications Statements   Text in bold font indicates user interface elements such as a menu items, buttons, check boxes, or column headings. For example:  Click the Start button, point to Programs, point to Accessories, and then click Command Prompt.  Under Notification Options, select the Warning Alarms check box. Text in Courier font indicates a file name, directory path, or command line text.
PAGE 13
Preface Communications Statements Federal Communications Commission (FCC) Class A Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PAGE 14
Preface Communications Statements CE Statement The CE symbol on the equipment indicates that this system complies with the EMC (Electromagnetic Compatibility) directive of the European Community (89/336/EEC) and to the Low Voltage (Safety) Directive (73/23/EEC). Such marking indicates that this system meets or exceeds the following technical standards: xiv  EN60950-1, A11:2004 – “Safety of Information Technology Equipment, Including Electrical Business Equipment”.
PAGE 15
Preface Laser Safety Information VCCI Class A Statement This is a Class A product based on the standard of the Voluntary Control Council For Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. Laser Safety Information This product may use Class 1 laser optical transceivers to communicate over the fiber optic conductors. The U.S.
PAGE 16
Preface License Agreements License Agreements Refer to the QLogic Software End User License Agreement for a complete listing of all license agreements affecting this product. General Public License QLogic routers are powered by the Linux operating system. A machine-readable copy of the Linux source code is available upon written request to the following address. A nominal fee will be charged for reproduction, shipping, and handling costs in accordance with the General Public License.
PAGE 17
Preface General Public License To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code.
PAGE 18
Preface General Public License 2. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately place on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. 3.
PAGE 19
Preface General Public License 4. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of paragraphs 1 and 2 above provided that you also do one of the following: a. Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of paragraphs 1 and 2 above on a medium customarily used for software interchange – or, b.
PAGE 20
Preface General Public License 6. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License.
PAGE 21
Preface General Public License 9. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyright interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 10.
PAGE 22
Preface General Public License PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
PAGE 23
Preface Technical Support Yoyodyne, Inc., hereby disclaims all copyright interest in the program ’Gnomovision’ (which makes passes at compilers) written by James Hacker. signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library.
PAGE 24
Preface Technical Support Contact Information QLogic Technical Support for products under warranty is available during local standard working hours excluding QLogic Observed Holidays. For customers with extended service, consult your plan for available hours. For Support phone numbers, see the Contact Support link at http://support.qlogic.com. Support Headquarters QLogic Corporation 4601 Dean Lakes Blvd. Shakopee, MN 55379 USA QLogic Web Site www.qlogic.com Technical Support Web Site http://support.
PAGE 25
1 Introduction This chapter describes the following features and capabilities of the iSR6152 router:  “Router Capabilities” on page 1-1  “Licensed Feature—Data Migration” on page 1-2  “Fibre Channel over IP (FCIP)” on page 1-2  “Chassis LEDs” on page 1-3  “Chassis Controls” on page 1-4  “Fibre Channel Ports” on page 1-6  “Fibre Channel SFP Transceivers” on page 1-7  “GbE Port LEDs” on page 1-8  “Ethernet Management Port” on page 1-9  “Serial Port” on page 1-9 Router Capabiliti
PAGE 26
1–Introduction Licensed Feature—Data Migration When using the iSR6152 to connect two Fibre Channel SANs, E_Ports are not required on the Fibre Channel switches. This allows you to connect multi-vendor Fibre Channel SANs (switches) without concern for the compatibility of the E_Ports and N_Ports between different switch vendors. The iSR6152 also has optional, additional servers and ports to expand connectivity.
PAGE 27
1–Introduction Chassis LEDs Chassis LEDs The chassis LEDs shown in Figure 1-2 provide information about the router’s operational status. These LEDs include the input power LED, heartbeat LED, and the system fault LED. To apply power to the router, plug the power cord into the router AC power receptacle and into a 100 VAC to 240 VAC, 50 Hz to 60 Hz power source. Heartbeat LED Power LED System Fault LED Figure 1-2.
PAGE 28
1–Introduction Chassis Controls Table 1-1. System Fault LED Blink Patterns (Continued) System Fault LED 1 Blink Condition Beacon, synchronized with the heartbeat LED Chassis Controls The maintenance button shown in Figure 1-3 is the only chassis control. Pressing this button resets the router or recovers the router if it has become disabled. Maintenance Button Figure 1-3. Chassis Controls Maintenance Button The maintenance button is a multifunction momentary switch on the front panel.
PAGE 29
1–Introduction Chassis Controls Reset and Select Boot Image You can reset the router using either the primary or secondary boot image:  Primary Image. To reset the router and select the primary boot image, use a pointed, nonmetallic tool to press and hold the maintenance button until the heartbeat LED flashes once, and then release the button. The router boots from the primary boot image. The boot time is less than one minute.  Secondary Image.
PAGE 30
1–Introduction Fibre Channel Ports  Disables the GbE ports and sets the IP address to 0.0.0.0.  Erases all presentations.  Erases all discovered initiators and targets. Fibre Channel Ports The iSR6152 router has two Fibre Channel ports, labeled FC1 and FC2, as shown in Figure 1-4. 2Gbps Activity LED 4Gbps Activity LED 8Gbps Activity LED Figure 1-4.
PAGE 31
1–Introduction Fibre Channel Ports Table 1-2 describes the port LED blink patterns and their meanings. Table 1-2.
PAGE 32
1–Introduction GbE Port LEDs GbE Port LEDs The four GbE ports shown in Figure 1-5 are RJ45 connectors that provide connection to an Ethernet SAN through a 100/1000 Base-T Ethernet cable. Link Status LED Activity LED Link Status LED Activity LED Figure 1-5. GbE Ports The GbE ports are labeled GE1, GE2, GE3, and GE4. Each GbE port has two LEDs:  The green (left) link status LED lights up to indicate that the link is up.
PAGE 33
1–Introduction Ethernet Management Port Ethernet Management Port The Ethernet management port shown in Figure 1-6 is an RJ45 connector that provides a connection to a management workstation through a 10/100 Base-T Ethernet cable. The port is labeled MGMT. Link Status LED Activity LED Figure 1-6.
PAGE 34
1–Introduction Serial Port 1-10 ISR651103-00 C
PAGE 35
2 Planning This chapter describes how to plan for the iSR6152 router.
PAGE 36
2–Planning Fibre Channel Performance Fibre Channel Performance The iSR6152 router supports Fibre Channel service at transmission rates of 2Gbps, 4Gbps, or 8Gbps with a maximum frame size of 2,148 bytes. It supports Ethernet service at transmission rates of 1000Mbps or 100Mbps with a maximum transmission unit (MTU) size of 1,500 bytes or 9,000 bytes (jumbo frames).
PAGE 37
2–Planning GbE Performance Latency Latency measures how long a transaction takes to travel through the router or over a communication link. GbE Performance The iSR6152 router supports Ethernet service at transmission rates of 1000Mbps or 100Mbps with a MTU size of 1,500 or 9,000 (jumbo frames).
PAGE 38
2–Planning Performance Tuning Table 2-1. T1 / DS-1—1.554 Mbps (Continued) Round Trip Delay (ms) Total Window Size (bytes) Scaling Factor 25 32K 0 20 32K 0 15 32K 0 10 32K 0 5 32K 0 2.5 32K 0 1 or less 32K 0 Table 2-2. T3 / DS-3—45 Mbps Round Trip Delay (ms) Total Window Size (bytes) Scaling Factor 250 1MB 5 100 512K 4 50 256K 3 25 128K 2 20 128K 2 15 64–128K 1 or 2 10 64K 1 5 32K 0 2.5 32K 0 1 or less 32K 0 Table 2-3.
PAGE 39
2–Planning Performance Tuning Table 2-3. DS-5—400 Mbps (Continued) Round Trip Delay (ms) Total Window Size (bytes) Scaling Factor 50 1MB 5 25 1MB 5 20 1MB 5 15 1MB 5 10 512K 4 5 256K 3 2.5 128K 2 1 or less 64K 1 Table 2-4. OC-1—50 Mbps Round Trip Delay (ms) Total Window Size (bytes) Scaling Factor 250 1MB 5 100 512K 4 50 256K 3 25 128K 2 20 128K 2 15 64–128K 1 or 2 10 64K 1 5 32K 0 2.5 32K 0 1 or less 32K 0 Table 2-5.
PAGE 40
2–Planning Performance Tuning Table 2-5. OC-3—150 Mbps (Continued) Round Trip Delay (ms) Total Window Size (bytes) Scaling Factor 100 1MB 5 50 1MB 5 25 512K 4 20 512K 4 15 256K 3 10 256K 3 5 128K 2 2.5 64K 1 1 or less 32K 0 Table 2-6. OC-12 and Above—621 Mbps 2-6 Round Trip Delay (ms) Total Window Size (bytes) Scaling Factor 250 1MB 5 100 1MB 5 50 1MB 5 25 1MB 5 20 1MB 5 15 1MB 5 10 1MB 5 5 512K 4 2.
PAGE 41
2–Planning Fibre Channel Switch Ports and Zoning Requirements Fibre Channel Switch Ports and Zoning Requirements The iSR6152 Fibre Channel ports are configured either as loop ports or in N_Port ID virtualization (NPIV). Therefore, the Fibre Channel switch port, (where iSR6152 Fibre Channel port is connected) must be configured to support a loop topology such as fibre loop port (FL_Port), generic port (G_Port), or NPIV.
PAGE 42
2–Planning Services  Save the router’s configuration (as a new file) after every configuration change, because you may:    Want to revert to a previous configuration. Need to configure a replacement router. Save the router’s mappings (as a new file) after every mapping change, because you may:    Want to revert to a previous mapping. Need to map a replacement router. Want to duplicate the mapping on a second router (for backup).
PAGE 43
3 Installation This chapter describes how to install and configure an iSR6152 router, and to install the firmware.
PAGE 44
3–Installation Installing the iSR6152 Router Table 3-1. Management Workstation Requirements (Continued) Item Internet browser Description One of the following:  Microsoft Internet Explorer 7.0 and later  Safari™  Java 2 runtime environment to support the Web applet Power Requirements Power requirements for the iSR6152 router are 0.5Amps at 100–125 VAC, 50Hz to 60Hz or 0.25Amps at 200–240 VAC, 50Hz to 60Hz.
PAGE 45
3–Installation Installing the iSR6152 Router Prior to installing the router, unpack the router and accessories. The iSR6152 router is shipped with the following components, shown in Figure 3-1:  Power cord.  Adapter (RJ45 to DB9F) for connecting the router’s serial port to a workstation used for configuring and managing the router. A standard Cat5 Ethernet cable is required (not supplied) to connect the adapter to the router. The adapter connects directly to the workstation’s serial (COM) port.
PAGE 46
3–Installation Installing the iSR6152 Router Pre-Installation Check List During the initial configuration process, the system prompts you for the parameters listed in Table 3-2. Complete this table before installation to expedite the configuration process. Table 3-2.
PAGE 47
3–Installation Installing the iSR6152 Router WARNING!! Mount routers in the rack so that the weight is distributed evenly. An unevenly loaded rack can become unstable, possibly resulting in equipment damage or personal injury. AVERTISSEMENT!! Installer les routeurs dans l’armoire informatique de sorte que le poids soit réparti uniformément. Une armoire informatique déséquilibré risque d'entraîner des blessures ou d'endommager l'équipement.
PAGE 48
3–Installation Installing the iSR6152 Router Installing the Transceivers The router supports a variety of SFP transceivers.  To install a transceiver, insert the transceiver into the port and gently press until it snaps in place.  To remove a transceiver, gently press the transceiver into the port to release tension, and then pull the release tab or lever and remove the transceiver. Different transceiver manufactures have different release mechanisms. Consult the documentation of your transceiver.
PAGE 49
3–Installation Installing the iSR6152 Router Setting the Workstation IP Address The IP address of a new router is 10.0.0.1. To ensure that your workstation is configured to communicate with the 10.0.0 subnet, refer to the following instructions for your workstation:  Steps for different versions of Windows vary. For a Windows 2000 workstation, follow these steps: a. From the Windows Start menu, select Settings>Control Panel>Network and Dial-up Connections. b. Click Make New Connection. c.
PAGE 50
3–Installation Installing the iSR6152 Router  For Linux: a. Set up minicom to use the serial port. Create or modify the /etc/minirc.dfl file with the following content: pr portdev/ttyS0 pu minit pu mreset pu mhangup pr portdev/ttyS0 specifies port 0 on the workstation. Choose the pr setting to match the workstation port to which you connected the router. b. 3. Verify that all users have permission to run minicom. Review the /etc/minicom.
PAGE 51
3–Installation Installing the iSR6152 Router Linux Installation Perform the following steps to install Router Manager from the QLogic Web site to a Linux workstation. To install Router Manager on Linux 1. Go to the QLogic Driver Downloads/Documentation page: http://driverdownloads.qlogic.com 2. Under Downloads, click QLogic Products. 3. Under QLogic Products, click the Routers link. 4. In the product selection window, click the iSR6152 model number, and then then click Go. 5.
PAGE 52
3–Installation Installing the iSR6152 Router Connecting the Router to AC Power WARNING!! This product is supplied with a three-wire power cable and plug for the user’s safety. To avoid electrical shock, use this power cable in conjunction with a properly grounded outlet. An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the router chassis. It is the customer’s responsibility to ensure that the outlet is correctly wired and grounded to prevent electrical shock.
PAGE 53
3–Installation Installing the Firmware To configure the router using the command line interface: 1. Open a command window according to the type of workstation and connection:  Ethernet (all platforms). Open a Telnet session with the default router IP address and log into the router with the default account name and password (guest/password) as follows. telnet 10.0.0.1 user name – guest password – ********   Serial. On Windows, open the HyperTerminal application.
PAGE 54
3–Installation Installing the Firmware WARNING!! Installing new firmware disrupts the router connectivity because you must reboot the router to activate the new firmware. The reboot may result in the transfer of incorrect data between devices connected to the router. QLogic recommends that you suspend activity on the interfaces before activating the new firmware. Using Router Manager to Install Firmware To install firmware using Router Manager: 1. In the topology view, double-click the router. 2.
PAGE 55
3–Installation Installing the Firmware 4. Use the put command to transfer the firmware image file from the workstation to the router. For example: ftp> put isr-6152-3_3_0_x.bin 200 PORT command successful. 150 Opening BINARY mode data connection for 'isr-6152-3_3_0_x.bin'. 226 Transfer complete. ftp – 4822816 bytes sent in 0.41Seconds 11878.86Kbytes/sec. 5. Type quit. The firmware image has been transferred to the router. 6. Log on to the router as an administrator.
PAGE 56
3–Installation Installing the Firmware 3-14 ISR651103-00 C
PAGE 57
4 Diagnostics and Troubleshooting Diagnostic information about the router is available through the chassis LEDs and the port LEDs. Diagnostic information is also available through the Router Manager and CLI event logs and error messages.
PAGE 58
4–Diagnostics and Troubleshooting Power-On Self-Test Diagnostics Input Power LED is Off The input power LED lights up to show that the router logic circuitry is receiving proper voltages. If the input power LED is off, follow these steps: 1. 2. 3. Inspect power cord and connectors. Is the cord unplugged? Is the cord or connector damaged?  Yes—Make necessary corrections or repairs. If the condition remains, continue with Step 2.  No—Continue with Step 2. Inspect AC power source.
PAGE 59
4–Diagnostics and Troubleshooting LED Blink Patterns Table 4-1. System Fault LED Blink Patterns System Fault LED Condition OFF OK - Operational 3 Blinks, followed by pause System error 4 Blinks, followed by pause Management port IP address conflict 5 Blinks, followed by pause Over temperature Heartbeat Blink Pattern A blink pattern on the heartbeat LED of one second ON followed by one second OFF means that the router is operating normally.
PAGE 60
4–Diagnostics and Troubleshooting Recovering a Router Over-Temperature Blink Pattern The system fault LED generates a five-blink pattern (once per second) followed by a two-second pause when the router is in an over-temperature condition. For example, this occurs when the air temperature inside the router is over the failure temperature of 70°C (158°F). If the system alert LED shows the over-temperature blink pattern, follow these steps: 1. 2. Inspect the chassis air vents.
PAGE 61
5 Removal and Replacement This chapter provides removal and replacement procedures for the following field replaceable units (FRUs):  SFP transceivers  iSR6152 router Removing and Replacing SFP Transceivers You can remove and replace the SFP transceivers while the router is operating without damaging the router or the transceiver. However, doing so interrupts transmission on the affected port until the transceiver is installed.
PAGE 62
5–Removal and Replacement Removing and Replacing the Router To remove a router: 1. Make sure all traffic (I/O operations to the router) subsides at the initiator systems. 2. Save the configuration data of the router using the CLI FRU command (see the iSR6152 Router CLI User's Guide). 3. Power down the router. 4. Disconnect the power cable. 5. Label all the cables so you can connect them to the same ports on the replacement router. 6. Remove all the Fibre Channel and Ethernet cables. 7.
PAGE 63
A Simple Network Management Protocol (SNMP) SNMP provides monitoring and trap functions for managing the router through third-party applications that support SNMP. The router firmware supports SNMP versions 1 and 2 and a QLogic (see page A-2). You may format the traps using SNMP version 1 or 2 (see page A-10). SNMP Properties You can set the SNMP properties using either the command line interface (CLI) (see the iSR6152 Router CLI Users Guide) or Router Manager (see the iSR6152 Router Manager Users Guide).
PAGE 64
A–Simple Network Management Protocol (SNMP) SNMP Trap Configuration Table A-1. SNMP Properties (Continued) Parameter Description System contact Name of the person to be contacted to respond to trap events. The name can be up to 64 characters excluding the number sign (#), semicolon (;), and comma (,). The default is undefined. Authentication traps Enables or disables authentication trap generation in response to authentication failures. The default is disabled.
PAGE 65
A–Simple Network Management Protocol (SNMP) Management Information Base (MIB) System Information The system information objects provide the system serial number, version numbers (hardware/software/agent), and number of ports (FC/GE). qsrSerialNumber Syntax: SnmpAdminString Access: Read only Description: System serial number. qsrHwVersion Syntax: SnmpAdminString Access: Read only Description: System hardware version number.
PAGE 66
A–Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrNwPortTable Syntax: Sequence of QsrNwPortEntry Access: Not accessible Description: Entries in this table include the management port and the GbE ports on the router. qsrNwPortEntry Syntax: QsrNwPortEntry Access: Not accessible Description: Each entry (row) contains information about a specific network port.
PAGE 67
A–Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrNwPortAddressMode Syntax: INTEGER 1 = Static 2 = DHCP 3 = Bootp 4 = RARP Access: Read only Description: Method by which the port gets its IP address. qsrIPAddressType Syntax: InetAddressType Access: Read only Description: IP address type: ipv4 or ipv6. qsrIPAddress Syntax: InetAddress Access: Read only Description: IP address of the port.
PAGE 68
A–Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrNwLinkRate Syntax: QsrLinkRate Access: Read only Description: Operational link rate for this port. Fibre Channel Port Table This table contains a list of the Fibre Channel ports on the router.There are as many entries in this table as there are Fibre Channel ports on the router. qsrFcPortTable Syntax: Sequence of QsrFcPortEntry Access: Not accessible Description: List of the Fibre Channel ports on the router.
PAGE 69
A–Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrFcPortIndex Syntax: Unsigned32 Access: Not accessible Description: A positive integer indexing each Fibre Channel port in a specified role. qsrFcPortNodeWwn Syntax: PhysAddress Access: Read only Description: World wide name of the node that contains this port. qsrFcPortWwn Syntax: PhysAddress Access: Read only Description: World wide name for this port.
PAGE 70
A–Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrFcLinkRate Syntax: QsrLinkRate Access: Read only Description: Current link rate for this port. Sensor Table This table contains a list of all the sensors on the router. There are as many entries (rows) in this table as there are sensors. qsrSensorTable Syntax: Sequence of QsrSensorEntry Access: Not accessible Description: List of all the sensors on the router.
PAGE 71
A–Simple Network Management Protocol (SNMP) Management Information Base (MIB) qsrSensorIndex Syntax: Unsigned32 Access: Not accessible Description: A positive integer identifying each sensor of a specific type. qsrSensorUnits Syntax: INTEGER Celsius = 1 Access: Read only Description: Unit of measurement for the sensor. qsrSensorValue Syntax: Integer32 Access: Read only Description: Current value of the sensor.
PAGE 72
A–Simple Network Management Protocol (SNMP) Notifications qsrSensorState Syntax: INTEGER Access: Read only Description: The state of this sensor, indicating the health of the system. Unknown—Sensor value/thresholds cannot be determined. Normal—Sensor value is within normal operational limits. Warning—Sensor value is approaching a threshold. Critical—Sensor value has crossed a threshold.
PAGE 73
A–Simple Network Management Protocol (SNMP) Notifications qsrEventTimeStamp Syntax: DateAndTime Access: Accessible for notify Description: This notification indicates when the event occurred. Agent Start Up Notification The agent startup notification indicates that the agent on the router has started running. qsrAgentStartup uses the following object:  qsrEventTimeStamp Agent Shut Down Notification The agent shut down notification indicates that the agent on the router is shutting down.
PAGE 74
A–Simple Network Management Protocol (SNMP) Notifications Sensor Notification The sensor notification indicates that the state for the specified sensor is not normal. When the sensor returns to the normal state, this event is sent with the qsrEventSeverity object set to clear. qsrSensorNotification uses the following objects:     qsrSensorValue qsrSensorState qsrEventTimeStamp qsrEventSeverity Generic Notification The generic notification reports events other than the defined event types.
PAGE 75
B Log Messages This appendix provides reference material on messages logged to a file. You can retrieve these message logs using either the CLI (see the iSR6152 Router CLI User’s Guide) or Router Manager (see the iSR6152 Router Manager User’s Guide). The message log is persistent, maintained across router power cycles and reboots.
PAGE 76
B–Log Messages Informational Log Messages Application Modules Table B-1 lists informational log messages generated by the application modules. Table B-1. Application Modules—Informational Log Messages ID Log Message No. 53254 System (router) Booting up 53357 QLBA_ProcessTpb: De-compression failed. Disabling compression temporarily 109 De-compression failed and is temporarily disabled.
PAGE 77
B–Log Messages Informational Log Messages Table B-1. Application Modules—Informational Log Messages (Continued) ID Log Message No. Description 54359 QLFC_HandleTeb: FC Login. VP 0x%x 1111 Fibre Channel login event notification, VP (virtual port) xx. 54368 QLFC_CreateVirtualInitiatorObject: Maximum host (%d) limit reached. 1120 Maximum number of support hosts dd has been reached. 54938 QLIS_HandleTeb: UTM_EC_OPEN_CONNECTION 1690 Event notification: iSCSI open connection request.
PAGE 78
B–Log Messages Informational Log Messages iSCSI Driver Table B-2 lists the informational log messages that are common to all iSCSI ports: 1 (GE1), 2 (GE2), 3 (GE3), and 4 (GE4). Log messages beginning with #0 denote iSCSI port 1 (GE1), #1 denotes iSCSI port 2 (GE2), #2 denotes iSCSI port 3 (GE3), and #3 denotes iSCSI 4 (GE4). Table B-2. iSCSI Driver—Informational Log Messages ID Log Message No. Description 86343 #%d: QLPortUp: Set link configuration 0x%x 327 iSCSI port enabled, port up.
PAGE 79
B–Log Messages Informational Log Messages Table B-3. Fibre Channel Driver—Informational Log Messages (Continued) ID Log Message No. Description 119088 #%d: QLIsrEventHandler: LIP occurred (%x): mailbox1 = %x 304 Fibre Channel loop initialization procedure (LIP) occurred. The LIP type is reported, as is the contents of the Fibre Channel processor’s mailbox 1 register. 119089 #%d: QLIsrEventHandler: LIP reset occurred (%x): mailbox1 = %x 305 Fibre Channel LIP reset occurred.
PAGE 80
B–Log Messages Informational Log Messages User Modules Table B-4 lists the log messages generated by the user modules. Table B-4. User Modules—Informational Log Messages ID Log Message No. Description 151842 FW Upgrade performed: new version is: %d.%d.%d.%d 290 Performed router firmware upgrade, new version number is d.d.d.d. 151843 REBOOT/SHUTDOWN Command from user. Code=%d 291 User performed a router reboot or shutdown.
PAGE 81
B–Log Messages Informational Log Messages Table B-4. User Modules—Informational Log Messages (Continued) ID Log Message No. 151899 qapimapremote_1_svc: Remotemap added to remote device %.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x 347 Remotemap added for remote Fibre Channel device WWPN xx.xx.xx.xx.xx.xx.xx.xx. 151900 qapiunmapremote_1_svc: Remotemap removed for local device %.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x 348 Remotemap removed for local Fibre Channel device WWPN xx.xx.xx.xx.xx.xx.xx.xx.
PAGE 82
B–Log Messages Informational Log Messages Table B-4. User Modules—Informational Log Messages (Continued) ID Log Message No. Description 151908 GE%d: Port status changed by user to ENABLED. 356 User enabled GE port d. 151909 GE%d: Port status changed by user to DISABLED. 357 User disabled GE port d. 151910 FC%d: Port status changed by user to ENABLED. 358 User enabled Fibre Channel port d. 151911 FC%d: Port status changed by user to DISABLED. 359 User disabled Fibre Channel port d.
PAGE 83
B–Log Messages Error Log Messages TOE Driver Table B-6 lists the informational log messages generated by the TOE driver. Table B-6. TOE Driver—Informational Log Messages ID 217350 Log Message QL3022:eth%x: Interface is down No. 262 Description The GbE interface d (0 or 1) used for an FCIP route is down. System Modules Table B-7 lists the informational log messages generated by the system modules. Table B-7.
PAGE 84
B–Log Messages Error Log Messages Application Modules Table B-8 lists the error log messages generated by the application modules. Table B-8. Application Modules—Error Log Messages ID Log Message No. Description 40967 QLBA_NullDoorbell: driver unloaded, port disabled 7 NULL doorbell routine for unloaded drivers. When a driver is unloaded, the doorbell routine is redirected to this NULL routine.
PAGE 85
B–Log Messages Error Log Messages Table B-8. Application Modules—Error Log Messages (Continued) ID Log Message No. 41107 QLBA_DisplayInitiatorOperationStatus: Transport Error, Status 0x%.2x 147 Process control block status indicates that a transport error (protocol) occurred during an initiator operation. 41111 QLBA_DisplayInitiatorOperationStatus: Data Overrun, Status 0x%.2x 151 Process control block status indicates that a data overrun error occurred during an initiator operation.
PAGE 86
B–Log Messages Error Log Messages Table B-8. Application Modules—Error Log Messages (Continued) ID Log Message No. Description 41283 QLIS_LoginPduContinue: TSIH 0x%x out of range 323 iSCSI Login PDU was received with a TSIH out of range. This would occur if the iSCSI initiator attempting the login failed to used the TSIH value provided in the Target Login Response PDU (router is target) in subsequent login PDUs.
PAGE 87
B–Log Messages Error Log Messages Table B-8. Application Modules—Error Log Messages (Continued) ID Log Message No. Description 41635 QLBI_GetLunInfo: QLBI_PassthruCommand failed for READ CAPACITY 675 Pass-Through command for Read Capacity command failed. The Read Capacity command was issued by the router as part of its discovery process. 41636 QLBI_GetLunInfo: READ CAPACITY failed, TPB status 0x%x 676 Read Capacity command failed.
PAGE 88
B–Log Messages Error Log Messages Table B-8. Application Modules—Error Log Messages (Continued) ID Log Message No. 41769 QLBI_GetLunList: REPORT LUNS command failed with CHECK CONDITION, SCSI STATUS 0x%02X 809 Report LUNs command failed with check condition status. The Report LUNs command was issued by the router as part of its discovery process. 41771 QLBI_GetLunList: Lun allocation failed for LunId %d 811 Failed to allocate LUN object: out of resources.
PAGE 89
B–Log Messages Error Log Messages Table B-8. Application Modules—Error Log Messages (Continued) ID Log Message No. Description 42242 QLIS_AllocateSessionObject: Out of session resources 1282 Failed to allocate object for iSCSI session: out of session resources. 42252 QLIS_EnqueueiScsiPdu: Duplicate PDU, CmdSN %d (0x%x), dropping it 1292 Received iSCSI PDU with duplicate command sequence number (CmdSN). Command PDU is dropped.
PAGE 90
B–Log Messages Error Log Messages Table B-8. Application Modules—Error Log Messages (Continued) ID Log Message No. Description 43268 QLUT_AllocateTpbExtension: Alloc of DSD failed for buffer len %d 2308 Allocation of DSD failed during Tpb extension allocation. Buffer length %d. 43269 QLFCIP_IncomingFrame: BUGCHECK: Trb (0x%p) ValidFlag (0x%x) Direction (0x%x) 2309 FCIP incoming frame: BUGCHECK: Trb (0x%p) ValidFlag (0x%x) Direction (0x%x).
PAGE 91
B–Log Messages Error Log Messages Table B-8. Application Modules—Error Log Messages (Continued) ID Log Message No. Description 43288 QLUT_FreeFcipTrb: Duplicate Free of FcipTrb (0x%p) 2328 FCIP free TRB: Duplicate Free of FcipTrb (0x%p). 43289 QLUT_InitializeFcipBufDescPool: Memory allocation for FCIP_BUF_EXT_DESC failed (size 0x%x) 2329 FCIP initialize buffer descriptor pool: memory allocation for FCIP_BUF_EXT_DESC failed (size 0x%x).
PAGE 92
B–Log Messages Error Log Messages iSCSI Driver Table B-9 lists the error log messages common to all iSCSI ports: 1 (GE1), 2 (GE2), 3 (GE3), and 4 (GE4). Log messages beginning with #0 denote iSCSI port 1 (GE1), #1 denotes iSCSI port 2 (GE2), #2 denotes iSCSI port 3 (GE3), and #3 denotes iSCSI 4 (GE4). Table B-9. iSCSI Driver—Error Log Messages ID Log Message No. Descriiption 73990 #%d: QLUtmIoctlEnable: Initialize FW failed 262 The iSCSI processor failed firmware initialization.
PAGE 93
B–Log Messages Error Log Messages Table B-9. iSCSI Driver—Error Log Messages (Continued) ID Log Message No. Descriiption 74663 #%d: QLReadyTimer: MBOX_CMD %04x %04x %04x %04x %04x %04x %04x %04x timed out 935 The driver timed out an iSCSI processor mailbox command. 74665 #%d: QLReadyTimer: QLiSNSReenable failed. 937 The driver timed out while attempting to reconnect with the iSNS. 74784 #%d: QLUpdateInitiatorData: No more room in Initiator Database.
PAGE 94
B–Log Messages Error Log Messages Table B-10. Fibre Channel Driver—Error Log Messages (Continued) ID Log Messages No. Description 106589 #%d: QLIoctlEnable: Adapter disabled 93 The Fibre Channel processor was disabled by an IOCTL request to the driver. 106590 #%d: QLIoctlEnable: Initialize FW error 94 The Fibre Channel processor firmware failed initialization. The request to initialize was received by the driver in an IOCTL request.
PAGE 95
B–Log Messages Error Log Messages Table B-10. Fibre Channel Driver—Error Log Messages (Continued) ID Log Messages No. Description 106928 #%d: QLMarkDeviceOffline: Device Id: %x marked offline, cLinkDownTimeout = %x, cPortDownRetryCount=%x 432 The driver was unable to re-establish connection to the target within the timeout and retry counts, and is therefore marking it offline.
PAGE 96
B–Log Messages Error Log Messages User Modules Table B-11 lists the error log messages generated by the user modules. Table B-11. User Modules—Error Log Messages ID Log Message No. Description 139265 QBRPC_Initialize: Entered 1 RPC (remote procedure call) server initialization entry point. 139266 QBRPC_Initialize:GetBridge Mem Allocation error 2 Get System API memory allocation failed.
PAGE 97
B–Log Messages Error Log Messages Table B-11. User Modules—Error Log Messages (Continued) ID Log Message No. 139284 QBRPC_Initialize:TargetList Mem Allocation error 20 Failed memory allocation for Get Target List API. 139285 QBRPC_Initialize:LunList MemAllocation error 21 Failed memory allocation for Get LUN List API. 139286 QBRPC_Initialize:PresTarget Mem Allocation error 22 Failed memory allocation for Get Presented Targets List API.
PAGE 98
B–Log Messages Fatal Log Messages Table B-11. User Modules—Error Log Messages (Continued) ID Log Message No. 139553 checkDuplicateIp: Detected Error %08x %08x%04x 289 Description Detected duplicate IP address for management port. System Modules Table B-12 lists the error log messages generated by the system modules. Table B-12. System Modules—Error Log Messages ID Log Message No Description 237572 "Failed to kill sys killer %d\n" 4 Failed to kill system task.
PAGE 99
B–Log Messages Fatal Log Messages Table B-13. iSCSI Driver—Fatal Log Messages ID Log Message No. Description 69652 #%d: qlutm_init: Diagnostic failed, invalid SRAM 20 iSCSI processor SRAM test failed. 69653 #%d: qlutm_init: Diagnostic failed, fail reboot 21 iSCSI processor failed diagnostic reboot. 69654 #%d: qlutm_init: Diagnostic failed, invalid NVRAM 22 iSCSI processor failed NVRAM diagnostic.
PAGE 100
B–Log Messages Fatal Log Messages Table B-13. iSCSI Driver—Fatal Log Messages (Continued) ID Log Message No. 70448 #%d: QLStartAdapter: QLRebootTimer failed AF %x RS %x Time %d 816 Start iSCSI processor reboot timer failed. 70489 #%d: QLIsrDecodeMailbox: System Error 8002 MB[1-7] %04x %04x %04x %04x %04x %04x %04x 857 iSCSI processor fatal system error. 70499 #%d: QLProcessResponseQueue: Invalid handle for ET_PASSTHROUGH_STATUS 867 Response queue invalid handle for ET pass-through.
PAGE 101
B–Log Messages Fatal Log Messages Table B-13. iSCSI Driver—Fatal Log Messages (Continued) ID Log Message No. Description 70836 #%d: QLStartFw: Invalid Fw loader state 0x%x 1204 iSCSI firmware loader invalid state. 70837 #%d: QLStartFw: Load Fw loader timeout 1205 iSCSI failed to load firmware in time allotted. Fibre Channel Driver Table B-14 lists the fatal log messages common to both Fibre Channel ports, 1 (FC1) and 2 (FC2).
PAGE 102
B–Log Messages Fatal Log Messages Table B-14. Fibre Channel Driver—Fatal Log Messages (Continued) ID Log Message No. 102657 #%d: QLInitializeAdapter: Load RISC code failed 257 Fibre Channel processor firmware load failed. 102658 #%d: QLInitializeAdapter: Load ISP2322 receive sequencer code failed 258 Fibre Channel processor receive sequencer code load failed.
PAGE 103
B–Log Messages Fatal Log Messages Table B-14. Fibre Channel Driver—Fatal Log Messages (Continued) ID Log Message No. Description 102747 #%d: QLProcessResponseQueueFS: Invalid buffer type: %x 347 FCIP: Response queue entry contains an invalid buffer type. 102748 #%d: QLProcessResponseQueueFS: Invalid EntryType (0x%x) 348 FCIP: Response queue entry contains an invalid entry type.
PAGE 104
B–Log Messages Fatal Log Messages System Modules Table B-16 lists the fatal log messages generated by the system modules. Table B-16. System—Fatal Log Messages ID Log Message No. Description 233473 "memory monitor: Detected Uncorrectable Ecc %08lx system is rebooting in 5 secs\n" 1 Uncorrectable memory error detected at address provided in log message. 233474 "Failed to register interrupt handler!\n" 2 Attempt to register the interrupt handler failed.
PAGE 105
Glossary activity LED A port LED that indicates when frames are entering or leaving the port. challenge-handshake authentication protocol See CHAP. adapter The board that interfaces between the host system and the target devices. Adapter is synonymous with host bus adapter (HBA), host adapter, and adapter board. CHAP Challenge-handshake authentication protocol. CHAP is used for remote logon, usually between a client and server or a Web browser and Web server.
PAGE 106
iSR6152 Intelligent Storage Router Installation Guide DHCP Dynamic host configuration protocol. Enables computers on an IP network to extract their configuration from servers that have information about the computer only after it is requested. driver The software that interfaces between the file system and a physical data storage device or network media. E_Port Expansion port. A port in a Fibre Channel switch that connects to another Fibre Channel switch or bridge device by an inter-switch link.
PAGE 107
iSR6152 Intelligent Storage Router Installation Guide FC-IP mode Data transportation mode in which the iSR6152 transports Fibre Channel frames over a TCP/IP connection using the FCIP protocol to connect two iSR6152 routers. In FC-IP mode, a port pair (one Fibre Channel port and an IP port on the same router) on local iSR6152 and another port pair on a remote router form an FCIP route. FCIP Fibre Channel over IP.
PAGE 108
iSR6152 Intelligent Storage Router Installation Guide generic port See G_Port. heartbeat LED A chassis LED that indicates the router status. hot replaceable Also known as hot swappable, this means you can add new devices or remove existing ones when the system is running. IANA Internet Assigned Numbers Authority (IANA) is responsible for the global coordination of the DNS root, IP addressing, and other Internet protocol resources.
PAGE 109
iSR6152 Intelligent Storage Router Installation Guide load balancing A software feature that improves system performance by balancing device access between multiple ports for maximum resource efficiency. loop initialization process See LIP. loopback Diagnostic tool that routes transmit data through a loopback connector back to the same adapter. LUN Logical unit number, a subdivision of a SCSI target.
PAGE 110
iSR6152 Intelligent Storage Router Installation Guide NL_Port Node loop port. A port capable of arbitrated loop functions and protocols. An NL_Port connects through an arbitrated loop to other NL_Port and at most a single FL_Port. NL_Ports handle creation, detection, and flow of message units to and from the connected systems. NL_Ports are end ports in virtual point-to-point links through a fabric, for example NL_Port to F_Port to F_Port to N_Port using a single Fibre Channel fabric switch.
PAGE 111
iSR6152 Intelligent Storage Router Installation Guide port instance The number of the port in the system. Each adapter may have one or multiple ports, identified with regard to the adapter as port 0, port 1 and so forth. To avoid confusion when dealing with a system containing numerous ports, each port is assigned a port instance number when the system boots up. So Port 0 on an adapter might have a port instance number of 8, for example, if it is the eighth port discovered by the system.
PAGE 112
iSR6152 Intelligent Storage Router Installation Guide target The storage-device endpoint of a SCSI session. Initiators request data from targets. Targets are typically disk-drives, tape-drives, or other media devices. Typically a SCSI peripheral device is the target but an adapter may, in some cases, be a target. A target can contain many LUNs. A target is a device that responds to a requested by an initiator (the host system).
PAGE 113
Index A AC power, connecting router 3-10 accessible parts support xv accessories included with router 3-3 activity LED definition of Glossary-1 Ethernet management port 1-9 GbE ports 1-8 adapter definition of Glossary-1 port beacon, definition of Glossary-1 port, definition of Glossary-1 application modules error log messages B-10 informational log messages B-2 arbitrated loop, definition of Glossary-1 audience ix authentication trap, enabling/disabling A-2 B bandwidth definition of Glossary-1 fiber optic
PAGE 114
iSR6152 Intelligent Storage Router Installation Guide DHCP definition of Glossary-2 enabling 1-5 diagnostics chassis 4-1 POST 4-2 discovered initiators, erasing 1-6 discovered targets, erasing 1-6 disk space requirements 3-1 workstation requirements 3-1 documentation conventions xi driver, definition of Glossary-2 dynamic host configuration protocol, See DHCP E E_Port definition of Glossary-2 on Fibre Channel switches 1-2 EEPROM definition of Glossary-2 updated message B-4 electrically erasable programmab
PAGE 115
iSR6152 Intelligent Storage Router Installation Guide Fibre Channel error log messages B-19 over IP 1-2 performance 2-2 port, MIB A-6 ports 1-6 SFP transceivers 1-7 Fibre Channel driver error log messages B-19 fatal log messages B-27 informational log messages B-4 Fibre Channel over IP, See FCIP Fibre Channel protocol, See FCP field replaceable unit, See FRU firmware installing 3-11 installing using CLI 3-12 FL_Port definition of Glossary-3 loop topology support 2-7 Flash iSCSI failure B-26 validation with
PAGE 116
iSR6152 Intelligent Storage Router Installation Guide informational log messages (continued) TOE driver B-9 user modules B-6 initiator definition of Glossary-4 erasing discovered 1-6 input power LED 1-3 input/output control, See IOCTL installing firmware, router 3-11 pre-installation check list 3-4 SANsurfer Router Manager on Windows 3-8 transceivers 3-6 installing, router 3-2 instance (port), definition of Glossary-7 Internet Assigned Numbers Authority, See IANA Internet browser, workstation requirements
PAGE 117
iSR6152 Intelligent Storage Router Installation Guide LEDs (continued) power 1-3 system fault 1-3, 4-2 license agreements (EULA) xvi general public xvi licensed features, key 1-2 link status LED Ethernet management port 1-9 GbE ports 1-8 Linux, installing SANsurfer Router Manager 3-9 LIP definition of Glossary-4 log message B-5 load balancing definition of Glossary-5 load balancing, definition of Glossary-5 localmap messages B-7 location name, router A-1 log messages B-1 error B-9 fatal B-24 informational
PAGE 118
iSR6152 Intelligent Storage Router Installation Guide non-volatile random access memory, See NVRAM notification agent shut down A-11 agent start up A-11 Fibre Channel port down A-11 generic A-12 MIB A-10 network port down A-11 objects A-10 sensor A-12 NTP definition of Glossary-6 services 2-8 NVRAM definition of Glossary-6 invalid data in B-18 O objects, notification A-10 operating system requirements, workstation 3-1 P path, definition of Glossary-6 performance Fibre Channel 2-2 GbE 2-3 tuning 2-3 plann
PAGE 119
iSR6152 Intelligent Storage Router Installation Guide router AC power, connecting to 3-10 capabilities of 1-1 configuring 3-10 description, features, capabilities 1-1 devices, cabling to 3-11 location A-1 mounting 3-4 multiple, connecting 2-7 recovering 4-4 removing 5-1 replacing 5-2 resetting 1-4 security with passwords 2-8 services 2-8 workstation, connecting to 3-6 router log B-1 definition of Glossary-7 RSCN definition of Glossary-7 receive message B-5 S Safari browser 3-2 safety, laser xv SAN definit
PAGE 120
iSR6152 Intelligent Storage Router Installation Guide T target definition of Glossary-8 database full error B-21 devices exceeded B-10 driver connection error B-21 driver database full error B-19 erasing discovered 1-6 failed memory allocation error B-23 iSCSI login error B-11 iSCSI login PDU error B-11, B-12 localmap for B-7 operation, PCI error during B-10 unknown path error B-19 TCP connection failure B-18 definition of Glossary-8 window scaling factor 2-3 window size 2-3 TCP/IP offload engine, See TOE
PAGE 121
iSR6152 Intelligent Storage Router Installation Guide WWPN definition of Glossary-8 Fibre Channel login error B-2 localmap for initiator B-7 localmap for target B-7 not found during logout B-14 remotemap for local B-6, B-7 remotemap for remote B-7 zoning based on 2-7 Z zoning, switch ports 2-7 ISR651103-00 C Index-9
PAGE 122
Corporate Headquarters QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656 949.389.6000 www.qlogic.com International Offices UK | Ireland | Germany | France | India | Japan | China | Hong Kong | Singapore | Taiwan © 2011 QLogic Corporation. Specifications are subject to change without notice. All rights reserved worldwide. QLogic and the QLogic logo are trademarks or registered trademarks of QLogic Corporation. AMCC is a registered trademark of Applied Micro Circuits Corporation.