Operation Manual

PICTURES
Front
Back
ASSEMBLY PROCEDURES
Hardware Used
EE
FF
II
1
1. Assemble the wheel assembly to the
bottom plate. Fix the wheel assembly to the
bottom plate using 4pcs bolt M6X12 and 4pcs
flange nut M6.
x 4
x 4
Wrench
x 1
M
J
K
DD
GG
OO
EE
FF
Bolt M6 X 12
M6 Flange nut
Hardware Used
2
2-1. Unscrew the switch button, load small
battery, tighten the switch button.
2-2. Insert the pins of the base to the holes of
lower support, press to secure the pins. Using
4pcs screw M5X12 to secure the lower support
and base.
Insert the pins of the control box assy to the
holes of upper support, press to secure the
pins. Using 4pcs screw 3/16” screw to secure
the upper support and control box assy.
GG
JJ
x 4
Philips
screwdriver
x 1
Screw M5 X 12
DD
x 4
3/16” Screw
AA Battery (1.5 V)
30
ASSEMBLY PROCEDURES
Hardware Used
EE
FF
II
1
1. Assemble the wheel assembly to the
bottom plate. Fix the wheel assembly to the
bottom plate using 4pcs bolt M6X12 and 4pcs
flange nut M6.
x 4
x 4
Wrench
x 1
M
J
K
DD
GG
OO
EE
FF
Bolt M6 X 12
M6 Flange nut
Hardware Used
2
2-1. Unscrew the switch button, load small
battery, tighten the switch button.
2-2. Insert the pins of the base to the holes of
lower support, press to secure the pins. Using
4pcs screw M5X12 to secure the lower support
and base.
Insert the pins of the control box assy to the
holes of upper support, press to secure the
pins. Using 4pcs screw 3/16” screw to secure
the upper support and control box assy.
GG
JJ
x 4
Philips
screwdriver
x 1
Screw M5 X 12
DD
x 4
3/16” Screw
AA Battery (1.5 V)
30
Hardware Used
JJ
Hardware Used
3. Assemble block belt.
Fix the block belt to the 2pcs of lower support
behind the front door, using 2pcs screw M5X12.
4. Assemble the middle support.
Insert the 4pcs upper support to the lower
support. Secure them with 8pcs screw 3/16”.
x 1
Philips
screwdriver
DD
JJ
x 8
x 1
Philips
screwdriver
3/16” Screw
GG
x 2
Screw M5 X 12
3
4
L
GG
D
DD
31
Hardware Used
JJ
Hardware Used
3. Assemble block belt.
Fix the block belt to the 2pcs of lower support
behind the front door, using 2pcs screw M5X12.
4. Assemble the middle support.
Insert the 4pcs upper support to the lower
support. Secure them with 8pcs screw 3/16”.
x 1
Philips
screwdriver
DD
JJ
x 8
x 1
Philips
screwdriver
3/16” Screw
GG
x 2
Screw M5 X 12
3
4
L
GG
D
DD
31
Hardware Used
5
6
5. Assebmle the flame screen to the upper
support.
Secure the flame screen to the upper support
using 8pcs screw 3/16”.
6. Assemble the reflector onto the flame
screen.
Screw the 3pcs stud on the flame screen,
put 3pcs washer Φ6 onto the top of stud,
then put the reflector onto the stud, secure
them with 3pcs washer Φ6 and 3pcs wing
nut.
AA
BB
CC
B
DD
x 3
x 3
x 6
Hardware Used
DD
JJ
x 8
Philips
screwdriver
3/16” Screw
x 1
AA
BB
Wing nut
Washer Φ6
CC
Stud
32
Hardware Used
5
6
5. Assebmle the flame screen to the upper
support.
Secure the flame screen to the upper support
using 8pcs screw 3/16”.
6. Assemble the reflector onto the flame
screen.
Screw the 3pcs stud on the flame screen,
put 3pcs washer Φ6 onto the top of stud,
then put the reflector onto the stud, secure
them with 3pcs washer Φ6 and 3pcs wing
nut.
AA
BB
CC
B
DD
x 3
x 3
x 6
Hardware Used
DD
JJ
x 8
Philips
screwdriver
3/16” Screw
x 1
AA
BB
Wing nut
Washer Φ6
CC
Stud
32
7
7. Carefully install the glass tube by lifting up
and inserting through the center hole in the
upper plate. Ensure the black silicone ring is
attached to the lower edge of the glass tube
as illustrated. Slide the glass tube through the
hole of the lower plate cover and onto the
middle plate. Check and ensure that the glass
tube is positioned properly and is completely
covering the center hole of the middle plate.
8. Assembly the protective guard.
Hang the hooks of the protective guard onto
the holes in supports.
Secure the protective guards with fixing
brackets with 4pcs 3/16" screws.
To aid in installation
place black silicone
ring on the middle
plate and then
install glass tube.
Ensure the rim of
the glass tube sits
firmly in the black
silicone ring.
WARNING! The black
silicone ring must be in place
prior to operating the heater.
BLACK SILICONE
RING
Hardware Used
DD
JJ
x 4
Philips
screwdriver
3/16” Screw
x 1
HH
Fixing
Bracket
x 4
8
E
DD
HH
33
7
7. Carefully install the glass tube by lifting up
and inserting through the center hole in the
upper plate. Ensure the black silicone ring is
attached to the lower edge of the glass tube
as illustrated. Slide the glass tube through the
hole of the lower plate cover and onto the
middle plate. Check and ensure that the glass
tube is positioned properly and is completely
covering the center hole of the middle plate.
8. Assembly the protective guard.
Hang the hooks of the protective guard onto
the holes in supports.
Secure the protective guards with fixing
brackets with 4pcs 3/16" screws.
To aid in installation
place black silicone
ring on the middle
plate and then
install glass tube.
Ensure the rim of
the glass tube sits
firmly in the black
silicone ring.
WARNING! The black
silicone ring must be in place
prior to operating the heater.
BLACK SILICONE
RING
Hardware Used
DD
JJ
x 4
Philips
screwdriver
3/16” Screw
x 1
HH
Fixing
Bracket
x 4
8
E
DD
HH
33
9
9. Attach the three side panels to the heater
using 18pcs screw 3/16”.
Note : Do not cover the front side where
the control knob is.
DD
Hardware Used
DD
JJ
x 18
Philips
screwdriver
3/16” Screw
x 1
10. Install the knob to M4X6 screw. Hang the
chain to the hole on the control box assy and
put the pothook of front panel to the holes of
bottom plate.
Hardware Used
x 1
KK
Knob
LL
JJ
x 1
x 1
Philips
screwdriver
Screw M4 X 6
x 1
MM
Chain
10
KK
LL
H
MM
34
1 1a
2
3 4 5
6 7 8
9 10 11