+ BE A TER LIE Fr CERT ATA har s 5 Lied d 3 FH Lind ol FRE LE £11] FEI raid i11 libel bn Foc, Ere hr LRA Thank you for choosing this SORCERESS "vehicle transceiver, REC Al UNIONS SERENE "always Provides high quality Radio products, this Transceiver is no exception. As you learn how to use this Please observe the following precautions to prevent fire, transceiver, you will find they SERENENESS is pursuing “user personal injury, landlord transceiver damage: friendliness’.
EE 3 PREPARATION # MOBILE INSTALLATION To Install the transceiver, select a safe, convenient location inside your vehicle that minimizes danger to your passengers and yourself while the vehicle Is in motion. Consider Installing the unit af en appropriate. position so that knees or legs wil not strike it during sudden braking of your vehicle.
a 3 PREPARATION 4% FIXED STATION OPERATION In order to uss this transceiver for fixed station operation, you will need a separate] 3.8 V DC power supply (not included). The recommended current capacity of your power supply is 2A. 1. Connect the DO power cable fo the regulated DO power supply and ensure that the polarities are correct (Red: positive, Black: negative).
BE 3 PREPARATION Hl ACCESSORY CONNECTIONS & EXTERNAL SPEAKER If you plan to usa an external partaker, choose a speaker with an impedance of 801. The external speaker jack accepts a 3.5 mm {178") omen {2-conductor) plug. move: External speaker adopt BTL double ports as output, please care about the connecting way.
GETTING ACQUAINTED i REAR PANEL @ Antenna conscious Cannes! an textual antenna [page 6] here. When transmitting, ‘the anteater system of load should be 500, © Data cable ® Connect this cable io rigger connector, as textual lama spring, {Optional parts) 8 13.8V DC cable ® Conn act 8 13.8V DC power source here, Use the supplied DC power cable Page 4] £ SP {Speaker} Jack ® if desired, connect an optional eternal speaker for cellar audio. this frack seacoasts a 3.5mm mono {2-conductor) plug see {Page 7}.
Please choose the syllable squelch level according lo the RF noise condition, 1 Repeatedly press MENU key until § shows as below, getting into squelch level setup men. SET MUTE hE 2 Turn [VOL nob to adjust the squelch level ® Select the level at which the background noise Is just eliminated when no signal is presented. ® The higher the level the strengthener signals must be 1b receive. mavens) * 18 different levels can be set.
I 7 18 ADVANCED OPERATION Available CSS dons frequency one resiliency 87.0 | 854 1072/1385 185511882 210712541 89.4 | 88.5 110.9 141.3 187.91180.9 218.1 | 258.1 71.9 191.5 1713/1928 2257 744 (948 118811514 173.8 196.6 228.1 TIO 974 177.3 196.5 2338 &F NOTE: Your gannet use the DOS function and COTES Tons fun. lions simultaneously. Switching the DOS function ON after having activated the MULTICS/ Tone functions deactivates the CAGES/ Tone functions.
ADVANCED OPERATION # Tha channel scan time can bs programmed by soft (default is 100ms). if the firm is too short, i will miss signal. If the time is foo long I will delay the progress of scan, ® [only scan channels on the same channel groups when scan start. ® if theta is CSS /DCS in-built. the device will decade and raviolis of mute after receiving signal. IF the coda is wrong, it will go on caning.
I © 18 AUXILIARY FUNCTION i GRAB CHANNEL When radio receive an available repeater signal, press a programmed grabbing channel function key i will immediately grab channel automatically fo make sure continuous commune. cation after the repeater signal disappears. HH BUSY CHANNEL LOCKOUT This function is used fo prevent transmitting on a channel or frequency that somebody alas is currently using.
| MAINTENANCE 9 HEE © NOTE: * Record the date of purchase, seal number and dealer from wham this product was purchased. * For your own information, retain a bitten record of any main penance performed on this product. * When claiming warranty service, please include a photocopy of the Bll of sale, or other proof-purchase showing the data of sale. BH CLEANING The keys, controls, and case of the transceiver are likely to become acid after extended use.
