User's Manual
Table Of Contents
- 1 Read This First
- 2 Safety Information
- 3 Overview
- 4 Preparing the System
- Inserting a microSD Card
- Using the Stand
- Charging the System
- Connecting the Transducer
- Removing the Transducer
- Using the System On The Go
- Using the Wheel Brakes
- Placing the Transducer Holder
- Mounting the System to the System Cart
- Adjusting the System Cart Height
- Connecting an External Printer
- Tilting the System
- Unmounting the System From the System Cart
- Moving the System
- Outputting the System Display to an HDMI-Enabled TV or Monitor
- Supported External Printers
- 5 Using the System
- Turning On/Off the System
- Logging Into the System
- Launching the Main Screen
- Setting the System Time and Date
- Controlling the System
- Setting the System Language
- Identifying the Main Screen Layout
- Switching the Control Panel Pages
- Managing the System Power
- Managing Disk Space
- Network Configuration
- DICOM Configuration
- 6 Performing an Exam
- Starting a New Exam
- Adding a New Patient
- Loading a Worklist
- Selecting a Preset
- Setting the Transducer Orientation
- Selecting/Switching a Scan Mode
- Adjusting the Displayed Image
- Freezing an Image
- Adding Annotations
- Adding Measurements
- Saving and Printing the Image
- Reviewing the Image
- Exporting the Exam
- Managing the Exam List
- Ending the Exam
- 7 Using Image Controls
- 2D Mode Image Controls
- Overview
- Adjusting Gain
- Adjusting Frequency
- Adjusting Time Gain Compensation (TGC)
- Adjusting the Scan Depth
- Adjusting the Focus Depth, Focal Zone and Focal span
- Adjusting Dynamic Range
- Using Tissue Harmonic Imaging (THI)
- Adjusting Persistence
- Adjusting Sharpness and Smoothing
- Adjusting Gray Map
- Adjusting Chroma Map
- Adjusting Steer Angle
- Adjusting the Sector Width and Position
- Adjusting Power
- Using Trapezoidal Imaging
- Adjusting Density
- Using Compound Imaging
- Using ENV (Enhanced Needle Visualization)
- Color/CPA Mode Image Controls
- M-Mode Image Controls
- Spectral Doppler Mode Image Controls
- 2D Mode Image Controls
- 8 System Customization and Service
- Customizing Your System
- Configuring Security Policies
- Servicing your system
- Reinstalling Software
- Checking the Software Version
- Checking the System’s Serial Number
- Checking the Tablet’s Serial Number
- Checking the License Status
- Resetting User Settings
- Backing Up System Settings and Patient Data
- Restoring System Settings and Patient Data
- Resetting Your System
- Testing the System
- Exporting System Logs
- Reading the User Manual
- 9 Transducers
- 10 Transducer Care
- 11 System Maintenance
- 12 Appendix
79
einnx
Adding Measurements
InnoSight Ultrasound System
P6992-4, EN, 16/12/6
When you are measuring, the indicators/lines display in yellow, allowing you to adjust as many times
as needed When you are done with measuring, use any of the following methods to complete the
measurement The indicators/lines then turns green, and the measured results (values) appear on the top
left side of the imaging screen
Two-finger tap on the scan area
Proceed with the next measurement
Touch Acquire to save the ultrasound image
To re-position the measured results, touch Result Pos
+/-
To set whether to show all or the last measured results, or to hide them all, touch Show Result
+/-
To delete measurements, touch Erase Meas to erase the last measurement added Repeat this
action, if needed, to continue erasing measurements
To directly erase all measurements, touch and hold Erase Meas
You can select whether to keep or erase the measurements added after you return to the live
scan by touching Menu > Settings > Workflow
> Auto-clear Measurement after Unfreeze
Measuring in 2D/Color/CPA Modes
Distance
Measure a distance
1 Touch Distance A crosshair cursor appears on the image Drag the target cursor to where you want to
start measuring and release it
2 Drag the target cursor to where you want to finish measuring, then release it to complete measurement
a
Ellipse
Measure a circumference
1 Touch Ellipse A crosshair cursor appears on the image Drag the target cursor to one end of the area
you want to measure and release it to set the start point of measurement
2 Drag the target cursor to the other end of the desired area, and release it to set the end point of
measurement An oval area is then measured
b
Trace
Manually trace an irregular shape
1 Touch Trace A crosshair cursor appears on the image Drag the cursor to where you want to start
measuring and release it
2 Drag the cursor along the outline of the object to trace
Figure 28Trace an outline