User's Manual
Table Of Contents
- 1 Read This First
- 2 Safety Information
- 3 Overview
- 4 Preparing the System
- Inserting a microSD Card
- Using the Stand
- Charging the System
- Connecting the Transducer
- Removing the Transducer
- Using the System On The Go
- Using the Wheel Brakes
- Placing the Transducer Holder
- Mounting the System to the System Cart
- Adjusting the System Cart Height
- Connecting an External Printer
- Tilting the System
- Unmounting the System From the System Cart
- Moving the System
- Outputting the System Display to an HDMI-Enabled TV or Monitor
- Supported External Printers
- 5 Using the System
- Turning On/Off the System
- Logging Into the System
- Launching the Main Screen
- Setting the System Time and Date
- Controlling the System
- Setting the System Language
- Identifying the Main Screen Layout
- Switching the Control Panel Pages
- Managing the System Power
- Managing Disk Space
- Network Configuration
- DICOM Configuration
- 6 Performing an Exam
- Starting a New Exam
- Adding a New Patient
- Loading a Worklist
- Selecting a Preset
- Setting the Transducer Orientation
- Selecting/Switching a Scan Mode
- Adjusting the Displayed Image
- Freezing an Image
- Adding Annotations
- Adding Measurements
- Saving and Printing the Image
- Reviewing the Image
- Exporting the Exam
- Managing the Exam List
- Ending the Exam
- 7 Using Image Controls
- 2D Mode Image Controls
- Overview
- Adjusting Gain
- Adjusting Frequency
- Adjusting Time Gain Compensation (TGC)
- Adjusting the Scan Depth
- Adjusting the Focus Depth, Focal Zone and Focal span
- Adjusting Dynamic Range
- Using Tissue Harmonic Imaging (THI)
- Adjusting Persistence
- Adjusting Sharpness and Smoothing
- Adjusting Gray Map
- Adjusting Chroma Map
- Adjusting Steer Angle
- Adjusting the Sector Width and Position
- Adjusting Power
- Using Trapezoidal Imaging
- Adjusting Density
- Using Compound Imaging
- Using ENV (Enhanced Needle Visualization)
- Color/CPA Mode Image Controls
- M-Mode Image Controls
- Spectral Doppler Mode Image Controls
- 2D Mode Image Controls
- 8 System Customization and Service
- Customizing Your System
- Configuring Security Policies
- Servicing your system
- Reinstalling Software
- Checking the Software Version
- Checking the System’s Serial Number
- Checking the Tablet’s Serial Number
- Checking the License Status
- Resetting User Settings
- Backing Up System Settings and Patient Data
- Restoring System Settings and Patient Data
- Resetting Your System
- Testing the System
- Exporting System Logs
- Reading the User Manual
- 9 Transducers
- 10 Transducer Care
- 11 System Maintenance
- 12 Appendix
InnoSight Ultrasound System
Setting the System Time and Date
inee
54
P6992-4, EN, 16/12/6
If a transducer is connected and the system displays the message No probe is connected,
remove then re-connect the transducer If the system still cannot detect the transducer, turn
off the system Wait for a few seconds and restart the system
You can choose the screen to enter after starting and logging in the system (with the
transducer connected) Go to Menu
>
Settings
>
Workflow
>
Screen after Enter Ultrasound
Setting the System Time and Date
Managing pertinent patient data and scanning results require accurate system time and date After
logging in the system for the first time, set current time and date based on your location The system then
maintains time and date settings even when the system is turned off and disconnected from power
2D Color PW
M CPA
Focus8.0
Dyn Range78
THI Full Screen
Dual Toggle
Freeze Acquire
Fn Key iScan TGC Home
2D
Menu
End Exam
Pen Res
Abdomen
12/5/2016 08:56 AM
C6-2
MI 0.72
TIS 0.02
32 Hz
16.0 cm
2D
Gen
Gn 44
DR 78
1/ 0/ 1
3/ 0/ 6
1
5
8:56 AM
12/6/2016
Monday
Long press button to launch settings
page.
Cast Display Off
Lan Connected
Storage Usage 85%
DICOM Connected
Touch to set current time and date.
System
toolbar
2
1
Figure 5Setting the system time and date
1 Touch anywhere on the system toolbar to open the system tools menu (See page 61)
2 Touch the time date section Set time/Set date
To set the time, scroll to select the hours, minutes, and am or pm
To set the date, scroll to select the date, month and year
3 Touch Done Touch
to leave the setting
Check and correct current system time and date based on your location every month to ensure
the accuracy