User's Manual
Table Of Contents
- 1 Read This First
- 2 Safety Information
- 3 Overview
- 4 Preparing the System
- Inserting a microSD Card
- Using the Stand
- Charging the System
- Connecting the Transducer
- Removing the Transducer
- Using the System On The Go
- Using the Wheel Brakes
- Placing the Transducer Holder
- Mounting the System to the System Cart
- Adjusting the System Cart Height
- Connecting an External Printer
- Tilting the System
- Unmounting the System From the System Cart
- Moving the System
- Outputting the System Display to an HDMI-Enabled TV or Monitor
- Supported External Printers
- 5 Using the System
- Turning On/Off the System
- Logging Into the System
- Launching the Main Screen
- Setting the System Time and Date
- Controlling the System
- Setting the System Language
- Identifying the Main Screen Layout
- Switching the Control Panel Pages
- Managing the System Power
- Managing Disk Space
- Network Configuration
- DICOM Configuration
- 6 Performing an Exam
- Starting a New Exam
- Adding a New Patient
- Loading a Worklist
- Selecting a Preset
- Setting the Transducer Orientation
- Selecting/Switching a Scan Mode
- Adjusting the Displayed Image
- Freezing an Image
- Adding Annotations
- Adding Measurements
- Saving and Printing the Image
- Reviewing the Image
- Exporting the Exam
- Managing the Exam List
- Ending the Exam
- 7 Using Image Controls
- 2D Mode Image Controls
- Overview
- Adjusting Gain
- Adjusting Frequency
- Adjusting Time Gain Compensation (TGC)
- Adjusting the Scan Depth
- Adjusting the Focus Depth, Focal Zone and Focal span
- Adjusting Dynamic Range
- Using Tissue Harmonic Imaging (THI)
- Adjusting Persistence
- Adjusting Sharpness and Smoothing
- Adjusting Gray Map
- Adjusting Chroma Map
- Adjusting Steer Angle
- Adjusting the Sector Width and Position
- Adjusting Power
- Using Trapezoidal Imaging
- Adjusting Density
- Using Compound Imaging
- Using ENV (Enhanced Needle Visualization)
- Color/CPA Mode Image Controls
- M-Mode Image Controls
- Spectral Doppler Mode Image Controls
- 2D Mode Image Controls
- 8 System Customization and Service
- Customizing Your System
- Configuring Security Policies
- Servicing your system
- Reinstalling Software
- Checking the Software Version
- Checking the System’s Serial Number
- Checking the Tablet’s Serial Number
- Checking the License Status
- Resetting User Settings
- Backing Up System Settings and Patient Data
- Restoring System Settings and Patient Data
- Resetting Your System
- Testing the System
- Exporting System Logs
- Reading the User Manual
- 9 Transducers
- 10 Transducer Care
- 11 System Maintenance
- 12 Appendix
InnoSight Ultrasound System
Symbols
2 enin
1
P6992-4, EN, 16/12/6
Do not use this system under direct sunlight, near heat sources or in the presence of flammable
substances, otherwise an explosion may occur
When using this system for ultrasound examinations, use only the qualified ultrasound gel that complies
with system standards
Do not continuously scan the same part of a patient or expose the patient to prolonged
scanning, otherwise it may harm the patient
Do not stay at the same position for too long without taking a break while scanning patients to
prevent harm or neck injury
Follow the instructions on Chapter 4 Preparing the System in this
User Manual
for complete
instructions on the installation of the transducers, power supply units and all peripheral devices to the
system
Improper installation of peripherals to the system may cause damage to the system, peripherals ,
or personal injury to the operator or the patient
Do not use the system for any application until you have read, understood, and know all the safety
information, safety procedures, and emergency procedures contained in this chapter Operating
the system without a proper awareness of safe use could lead to fatal or other serious personal
injury
The system can contain environmentally hazardous materials such as, but not limited to: heavy metals,
general recyclable metals, and plastics This product should be recycled according to local and national
guidelines for recycling electronic equipment
When using additional peripheral equipment powered from an electrical source other than the
ultrasound system, the combination is considered to be a medical system It is your responsibility to
comply with IEC 661-1 and test the system to those requirements
Do not use non-medical peripherals, such as report printers, within 1 m ( ft) of a patient, unless
the non-medical peripherals receive power from an isolation transformer that meets medical safety
standards, as defined by standard IEC 661-1
Images printed on a report printer are intended only for reference and should not be used for diagnostic
purposes
For proper disposal of this system, contact your local Philips representative
Symbols
The following symbols provide information about the system’s labels and regulatory compliance
Do not use a brush on the system’s labels
System Label Icons
Symbols Descriptions
Product Model
Serial Number