User's Manual
Table Of Contents
- 1 Read This First
- 2 Safety Information
- 3 Overview
- 4 Preparing the System
- Inserting a microSD Card
- Using the Stand
- Charging the System
- Connecting the Transducer
- Removing the Transducer
- Using the System On The Go
- Using the Wheel Brakes
- Placing the Transducer Holder
- Mounting the System to the System Cart
- Adjusting the System Cart Height
- Connecting an External Printer
- Tilting the System
- Unmounting the System From the System Cart
- Moving the System
- Outputting the System Display to an HDMI-Enabled TV or Monitor
- Supported External Printers
- 5 Using the System
- Turning On/Off the System
- Logging Into the System
- Launching the Main Screen
- Setting the System Time and Date
- Controlling the System
- Setting the System Language
- Identifying the Main Screen Layout
- Switching the Control Panel Pages
- Managing the System Power
- Managing Disk Space
- Network Configuration
- DICOM Configuration
- 6 Performing an Exam
- Starting a New Exam
- Adding a New Patient
- Loading a Worklist
- Selecting a Preset
- Setting the Transducer Orientation
- Selecting/Switching a Scan Mode
- Adjusting the Displayed Image
- Freezing an Image
- Adding Annotations
- Adding Measurements
- Saving and Printing the Image
- Reviewing the Image
- Exporting the Exam
- Managing the Exam List
- Ending the Exam
- 7 Using Image Controls
- 2D Mode Image Controls
- Overview
- Adjusting Gain
- Adjusting Frequency
- Adjusting Time Gain Compensation (TGC)
- Adjusting the Scan Depth
- Adjusting the Focus Depth, Focal Zone and Focal span
- Adjusting Dynamic Range
- Using Tissue Harmonic Imaging (THI)
- Adjusting Persistence
- Adjusting Sharpness and Smoothing
- Adjusting Gray Map
- Adjusting Chroma Map
- Adjusting Steer Angle
- Adjusting the Sector Width and Position
- Adjusting Power
- Using Trapezoidal Imaging
- Adjusting Density
- Using Compound Imaging
- Using ENV (Enhanced Needle Visualization)
- Color/CPA Mode Image Controls
- M-Mode Image Controls
- Spectral Doppler Mode Image Controls
- 2D Mode Image Controls
- 8 System Customization and Service
- Customizing Your System
- Configuring Security Policies
- Servicing your system
- Reinstalling Software
- Checking the Software Version
- Checking the System’s Serial Number
- Checking the Tablet’s Serial Number
- Checking the License Status
- Resetting User Settings
- Backing Up System Settings and Patient Data
- Restoring System Settings and Patient Data
- Resetting Your System
- Testing the System
- Exporting System Logs
- Reading the User Manual
- 9 Transducers
- 10 Transducer Care
- 11 System Maintenance
- 12 Appendix
9
2 enin
2
P6992-4, EN, 16/12/6
2
Safety Information
Follow the procedures carefully and ensure that the power/electrical/environmental requirements
are satisfied Failure to observe the instructions or disregard the warnings may result in damages
to the system, personal injury, or even death of the operator or the patient
Observe the following precautions carefully
This system complies with Type BF general equipment and the EN661-1 standard, suitable for
continuous operation when connected as a system to a medical grade AC/DC power adapter or
operated from the tablet battery
Use only medical grade peripherals in the patient environment
Do not block or otherwise obstruct access to the AC plug at the wall Operators must be able to
quickly unplug the power cable at the wall in case of emergency
The system should only be used in a medical facility under the supervision of a trained physician
Only an authorized service technician should perform maintenance
Be extremely cautious when placing or moving the system
Always position the system on a stable surface where it cannot fall on the patient
Do not lift the system by the power cable or the transducer If either disconnects, the system
could fall on the patient
This system has been fully adjusted and tested prior to shipment from the factory Unauthorized
modifications will void your warranty
If this system or the transducer connected displays any signs of malfunction, turn off the system
immediately, disconnect it from the wall outlet, then contact technical support (See Customer
Service on page 3)
Do not use a power adapter other than the one supplied with the system Connecting the
system to an unknown power adapter is very dangerous and may lead to fire or explosion
Using cables, transducers, or accessories other than those specified for use with the system
may result in increased emissions or decreased immunity of the system
The power cable of the system should only be connected to a grounded power socket
Do not connect USB peripherals with an extended USB cable Extended connection may cause
unexpected usage fault
Only devices that comply with the EN661-1 standard, either electronically or mechanically, can be
connected to this system Recheck the leakage current and other safety performance indices of the
entire system to avoid potential system damage caused by leakage from a current superposition
Using accessories, transducers, peripherals, or cables not supplied with the system or
recommended by Philips can affect the system in the form of increased emissions or decreased
immunity to external EMI/EMC occurrences Non-specified peripherals, and cables in some cases,
can also increase leakage current or compromise the safety of the grounding scheme
This system does not incorporate any specialized protective measures in the event it is configured with
high-frequency operation devices The operator should use with caution in these types of applications
The system is in compliance with the Ingress Protection Marking ratings IP22