User's Manual
Table Of Contents
- 1 Read This First
- 2 Safety Information
- 3 Overview
- 4 Preparing the System
- Inserting a microSD Card
- Using the Stand
- Charging the System
- Connecting the Transducer
- Removing the Transducer
- Using the System On The Go
- Using the Wheel Brakes
- Placing the Transducer Holder
- Mounting the System to the System Cart
- Adjusting the System Cart Height
- Connecting an External Printer
- Tilting the System
- Unmounting the System From the System Cart
- Moving the System
- Outputting the System Display to an HDMI-Enabled TV or Monitor
- Supported External Printers
- 5 Using the System
- Turning On/Off the System
- Logging Into the System
- Launching the Main Screen
- Setting the System Time and Date
- Controlling the System
- Setting the System Language
- Identifying the Main Screen Layout
- Switching the Control Panel Pages
- Managing the System Power
- Managing Disk Space
- Network Configuration
- DICOM Configuration
- 6 Performing an Exam
- Starting a New Exam
- Adding a New Patient
- Loading a Worklist
- Selecting a Preset
- Setting the Transducer Orientation
- Selecting/Switching a Scan Mode
- Adjusting the Displayed Image
- Freezing an Image
- Adding Annotations
- Adding Measurements
- Saving and Printing the Image
- Reviewing the Image
- Exporting the Exam
- Managing the Exam List
- Ending the Exam
- 7 Using Image Controls
- 2D Mode Image Controls
- Overview
- Adjusting Gain
- Adjusting Frequency
- Adjusting Time Gain Compensation (TGC)
- Adjusting the Scan Depth
- Adjusting the Focus Depth, Focal Zone and Focal span
- Adjusting Dynamic Range
- Using Tissue Harmonic Imaging (THI)
- Adjusting Persistence
- Adjusting Sharpness and Smoothing
- Adjusting Gray Map
- Adjusting Chroma Map
- Adjusting Steer Angle
- Adjusting the Sector Width and Position
- Adjusting Power
- Using Trapezoidal Imaging
- Adjusting Density
- Using Compound Imaging
- Using ENV (Enhanced Needle Visualization)
- Color/CPA Mode Image Controls
- M-Mode Image Controls
- Spectral Doppler Mode Image Controls
- 2D Mode Image Controls
- 8 System Customization and Service
- Customizing Your System
- Configuring Security Policies
- Servicing your system
- Reinstalling Software
- Checking the Software Version
- Checking the System’s Serial Number
- Checking the Tablet’s Serial Number
- Checking the License Status
- Resetting User Settings
- Backing Up System Settings and Patient Data
- Restoring System Settings and Patient Data
- Resetting Your System
- Testing the System
- Exporting System Logs
- Reading the User Manual
- 9 Transducers
- 10 Transducer Care
- 11 System Maintenance
- 12 Appendix
93
inen
Color/CPA Mode Image Controls
InnoSight Ultrasound System
P6992-4, EN, 16/12/6
In CPA (Color Power Angio) mode, low flow rate in small vessels are clearly observed Colors are carried
out only to demonstrate the blood flow, but contain no velocity information, thus, offer no directional
information
2D PW
M
TGC
2D
C6-2
2D
1
5
Figure 36CPA mode real-time scan
Both Color and CPA modes can work with other scan modes to form duplex and triplex modes
Adjusting Pulse Repetition Frequency (PRF)
Adjust the velocity range of the color flow display The maximum velocity range depends on the transducer
in use and the location of the sample volume Set the PRF high enough to prevent aliasing, and low enough
to provide adequate detection of slow blood flow Upon adjusting the PRF value, the velocity scale shown
on the Color/CPA wedge and the Wall Filter setting are changed accordingly
Touch Scale +/- to adjust the value
Adjusting Wall Filter (WF)
Reduce or eliminate unwanted low-frequency, high-intensity signals generated by movements of blood
vessel walls or by rapid movement of the transducer Set the wall filter high enough to ensure that the
Color Doppler flash artifacts from tissue or wall motion are not displayed, but low enough to display slow
flow The adjustable range of the Wall Filter value is related to the current PRF value
Touch Wall Filter +/- to adjust the value
Applying the Smoothing Filter
Reduce color noise by applying a smoothing filter to the image
Touch Smoothing +/- to adjust the value
Adjusting the Color Priority
Define the amount of color displayed over bright echoes, and help confine color within the vessel walls
Touch Priority +/- to adjust the value