QSDR04RTC USER’S MANUAL Contact US: Q-see Products 8015E.Crystal Dr Anaheim, CA 92807 Website: http://www.q-see.com Customer Service: Phone: 877-998-3440 x 538 Email:cs@dpsi-usa.com Tech Support: Phone: 877-998-3440 x 539 Email:ts@dpsi-usa.
CONTENTS Chapter 1: DVR Features ...................................................................................................................................................2 Chapter 2: Layout ..............................................................................................................................................................3 2.1 Front Panel ........................................................................................................................................
5.2.7.3 Video Setup....................................................................................................................................................25 5.2.7.4 Language........................................................................................................................................................26 5.2.7.5 Info...............................................................................................................................................................
User Manual Safety Instructions 1. Use proper power source. Do not use this product with a power source that applies more than specified voltage (100-240V AC). 2. Never insert anything metallic into the DVR case. Putting something into the DVR case can be a source of dangerous electric shock. 3. Do not operate in wet & dusty area or use near water. Avoid places like a damp basement or dusty hallway. 4. Do not expose this product to rain or use near water.
User Manual Chapter 1: DVR Features Real time monitoring Supports real time surveillance via Monitor Saves Recordings DVR saves real-time recording image to HDD Backup Recordings Supports DVR backup via USB flash drive and hard drive.
User Manual Chapter 2: Layout 2.1 Front Panel Item Key title/Indicator Marks 1 HDD indicator HDD When the “Red” indicator flashes it means the hard drive is being read or written to.
User Manual 2.
User Manual 2.
User Manual Chapter 3: DVR Installation 3.1 Hard Drive Installation ： Please do not Install or take out hard drive when DVR is running! Caution (1) Remove screws and open DVR upper cover carefully; (2) Insert Power Cord and data cable into Pin of hard drive securely; (3) Put the upper cover back carefully, re-attach screws. 3.2 Camera and Monitor Connection Connect camera cable to video input of DVR, and from video output of DVR to Monitor via BNC connector (Refer to section2.
User Manual Chapter 4: DVR Boot up 4.1 System Initialization After connecting the power adapter and turning On the power button, the system will boot-up and start initializing. Picture 4-1 4.2 Main Interface Picture 4-2 After finishing system initialization the system will enter into main interface. Picture 4-2 is the main interface displayed by system, which is showing no video input status. Once there are video inputs, the interface will display live images from the cameras.
User Manual 5.1 Main Menu Preview Color set Camera Dwell time display Recording Network Search Playback Rec. Search Detail File File Backup Main Menu HDD Management Alarm Setting Device Management E-mail setting PTZ Setting Mobile Motion Area setting Time Setting User password Video Setting System Language Select System Information System Maintenance 5.2 Main Menu Picture 5-2 After clicking right button of mouse, pop-up menu will be displayed on the screen.
User Manual 5.2.1 Camera setup Go to [Main Menu Camera] to set up the name display and position display of each channel (Shown as Picture 5-3), You can also adjust image brightness, saturation, contrast and hue settings of each channel after entering into [Color] Menu and set up whether each channel can be previewed or not under Live display and/or Recording mode. Please note that the name of each channel supports up to eight characters or four Chinese characters.
User Manual The [Record Setup] menu allows you set up recording status (on/off) of each channel, it also allows you setup recording image resolution and quality, and turn audio on/off. This menu also allows you select recording mode (recording after power on and scheduled recording) and recording file length. Once a channel is set to “on” the channel can record, if it is set to “off” the video from the channel will not be recorded.
User Manual 5.2.3.2 PPPoE When selecting PPPoE, you need to input user and password provided by your internet service provider and set up web port (for details refer to the below picture 5-8) . Picture 5-8 5.2.3.3 Static When selecting static allocation, You will need to setup the network settings on the DVR to match the settings of the router that you attach the DVR to.
User Manual 5.2.3.4 Port Forwarding To access the DVR from a remote computer over the internet you would then need to forward port 80 and port 9000 on the router the DVR is attached to, to the IP address of the DVR. You can get instructions on how to do this for most popular routers by going to the www.portforward.com website.
User Manual Picture 5-17 Picture 5-16 To connect to the DVR from the remote computer you would then open an Internet Explorer browser window and enter the internet IP of your router that you got by going to www.myipaddress.com. Notice: If you cannot use HTTP port 80 or 9000 because it is being used by another program, or it is being blocked by your service provider, you can use another port in the same range.
User Manual You can play video Forward at 2x, 4x, and 8x speeds, Slow play at 1/2x, 1/4x, and 1/8x, normal play, pause and play frame by frame using the playback control bar, and adjust volume by clicking or sliding tune control bar. When playback has finished, system will return to previous menu. File list On the [Video search] menu mode, click [File list] to pop up the sub-menu shown below as Picture 5-21.
User Manual Picture 5-24 、 Picture 5-25 3 Open backup file: 1. Click [Play] menu (P) on the top of multimedia player interface to select playing the backup file; Picture 5-26 2. Click pop-up menu button on the bottom of multimedia player and [Play- ] button, then the backup file will be played on the according channel. 3. The Menu brief on the bottom of multimedia player: recording date for the current backup file shown as right corner; Date: 24H recording time: lie under [Date] menu.
User Manual 4. Please refer to the below [Video on] setting procedure (System default - video for every channel is on) Setting Video play setting Normal video Bar Select the channel you want to display Select to play the video Apply OK Picture 5-27 Picture 5-27A 5. Refer to the below for [Audio on] setting procedure. (Setting parameter will be available after re-starting multimedia player after [Audio on] set up.
User Manual When you install a HDD, the system will automatically detect if HDD is formatted or not; If HDD needs to be formatted, HDD status will be shown as “Not format”, otherwise, the HDD status will be shown as “Normal” (refer to Picture 5-31) TOTAL SPACE: Indicates total space available on Hard Drive. FREE SPACE: Indicates unused space available on the Hard Drive.
User Manual Email Alarm Notification (to send notice to email account when motion alarm is triggered) Click the [Email setup] menu to enter into its sub menu (shown as Picture 5-33). Picture 5-33 On the [Email setup] mode, refer to its parameter setup shown as picture 5-34 when setting email alarm to “on”. SSL: is a security link transport protocol.
User Manual soon as possible to avoid overloading your email account. For detailed SMTP protocols settings refer to the below picture 5-35A. Picture 5-35A 5.2.6.3 PTZ Setup Enter into [Main menu Device PTZ Setup] to select the channel you want to control and set PTZ protocol (Pelco-D or Pelco-P), Baud Rate (1200, 2400, 4800, 9600), Stop bit (1, 2), Parity Check (None, Odd, Even Mark Space), Address Code and Cruise status respectively.
User Manual When accessing from a mobile phone with Windows Mobile operating system, use the following procedure: 1. Webcam installation First you need to install the webcam program that is included on the CD that comes with the DVR by copying the “QQeye.CAB” file to the mobile phone.
User Manual the DVR, setting range is between 1024 and 65535, the default setting is 18600. Note: this port is in addition to the ports used for standard remote access. Channel: Select the channel from the DVR you want to monitor and click [OK] button (red box in Pic 7) to display the screen in Pic 8 and start video connection. 6. Main interface operation (Pic 8) Click [Disconnect] button to stop displaying live image of the channel. Click [Setting] button to modify the settings. 7.
User Manual 3. Click the Continue button (red box in Pic 5) on the information box displaying the program and current version. This will display the window in Pic 6. 4. Next choose where you want to install the program, to phone memory or to the memory card, and click on the Select option (red box in Pic 6). This will display the window in Pic 7, click on Continue (red box in Pic 7) which will display the screen in Pic 8 and tell you it is installing the program (red box in Pic 8). Pic 7 Pic 8 Pic 9 5.
User Manual By clicking on the image you can see it full screen as in Pic 13 Pic 13 When accessing from an iphone, use the following procedure: On the DVR: The DVR must have the latest Firmware version 090706 or newer Go to Menu – Devices – Mobile Set User name and password. Example admin / admin Set the port: 18004 From the PC, forward port 18004 in the router going to the IP of DVR.
User Manual Click Play button on the bottom left corner (red box in first picture below) to connect to DVR. After connecting, CH1 will display as shown in the second picture below. You can change to CH2 by push # 2 (red box in second picture below). If you have an 8 camera system you would click on the down arrow in the bottom row (red box in first picture below) to view the buttons to access the next 4 cameras (as shown in the red box in the second picture below).
User Manual 5.2.7 System Function The [System] Menu includes the below sub-menus: Time Set, User Password, Audio/Video Setting, Language select, System Info and System Maintenance. After entering into the [System], you can configure the system to meet your needs. Picture 5-40 5.2.7.
User Manual 5.2.7.4 Language Enter into [System Language] menu to select the language you want to use on the DVR (shown as Picture 5-45) and click [APPLY] button. The selection will be available after system Auto restarts. Picture 5-45 5.2.7.5 Info. Click [Main Menu System Info] to enter into [System Information] menu to view system info, including Device type, Software (firmware) version and MAC address etc. Picture 5-46 5.2.7.
User Manual 5.5 PTZ Control We introduced setting PTZ parameters previously in chapter 5.2.5.3. Here we will discuss how to operate PTZ controls. Click pop-up menu to show PTZ option and enter into PTZ control interface (shown as Picture 5-49). You can now click Z+&Z- keys to zoom In or out, click F+&F- keys to control camera focus and click I+&I- to adjust iris.
User Manual Chapter 6: Net-Viewer Program 6.1 Plug-ins download and installation Open IE browser and input IP address and web port of DVR, such as http://172.18.6.202 and confirm to download and install webcam. If your computer is connected to internet, computer will auto download and install the webcam. Reminder: If the webcam is not downloaded successfully, please check if your browser’s safety level or firewall setting is too advanced. Also refer to section 5.2.
User Manual 6.3 Main Interface of Net-viewer Picture 6.3 Log in Net-viewer and show the interface as follows 6.3.1 Menu column (Section 1 on Picture 6-3) 6.3.2 PTZ Control (Numbers 2, 3, 4 on Picture 6-3) 6.3.3 Live Play Control (Numbers 6 through 10 on Picture 6-3) 6.3.1 Menu column (Section 1 on Picture 6-3) Menu column include [Live] menu, [Replay] menu and [Setup] menu and [Logout] menu. 6.3.1.1 Live After Logging-in to system, system will enter into Live display (shown as Picture 6-3). 6.3.1.
User Manual F.F. button: fast forward playback recording Slow button: slow playback recording. Next Frame: play frame by frame. 264 TO AVI button: convert file from H.264 format to AVI format The native format of the backup files is H.264, you can convert H.264 format into more familiar AVI format by clicking the key of 264 to AVI. 6.3.1.3.
User Manual System allows you setup motion detection settings for each channel of DVR remotely (shown as Picture 6-8) Picture 6-8 ③ PTZ Control Click [PTZ control] to setup PTZ cameras. Remote setup methods are the same as local DVR setup. Please refer to Section 5.2.5.3 (shown as Picture 6-9). ④ Network Picture 6-9 Click [Network] to enter into [Network] menu. Remote setup methods are the same as local DVR setup. Please refer to Section 5.2.3. – Network Set.
User Manual 6.3.1.4 Log out Log out of the system. 6.3.2 PTZ Control (Numbers 2, 3, 4 on Picture 6-3) Note: below-mentioned series no will be consistent with the remark no shown as Picture 6-2. 2 .PTZ direction control: Control PTZ moving direction 3 .Zoom, Focus and Iris Control: control direction, zoom, focus and iris of PTZ. 4 .
User Manual Chapter 7: Specifications QSDR04RTC Model Video System NTSC / PAL(Optional) Compression Format Video Video Input/Output 4-CH BNC Input/ 2-CH BNC Output / 1-VGA output Audio I/O 4-CH RCA audio Input / 2-CH RCA audio Output Display Resolution D1 ：H.
User Manual Chapter 8: Appendix 8.1 Operation Function Table Type Title Time setting Language Select CH Setting Principle Setting Setting Network Setting Network Function Auxiliary function Menu button Setting system date, time and format and day-light saving time setting Setting system language Setting CH title and position; adjusting image color parameter value; setting CH display to ON / Off and time display/recording time overlaying to On/Off. Rec.
User Manual 8.2 Recording Alarm setting ⊥ Please refer the below matrix: “ ” stand for “only alarm but no recording”; “AMR” stand for “alarm recording”; “NLR” stand for “normal recording”; and “NOR” stand for “ no recording”. Once alarm is triggered, alarm icon will occur, and when many alarms are triggered, alarm remarks will occur on the screen.
User Manual 8.4 System Connections (Diagram is for reference only to show where to attach various devices to the DVR, the cameras, external alarms, USB flash drives, monitors and computers are not included with the standard DVR package) 8.
User Manual Q-See Product Warranty Thank you for choosing our products. All of our products users have a conditional free warranty repair service for hardware within 12 months starting from purchase date, and a free exchange service within one month (valid for manufacturing defects). Permanent upgrading service is provided for the software. Liability Exclusions: Any product malfunction, abnormalities in operation or damage caused by following reasons are not within the free service scope of our company.
User Manual Customer Information Card User’s Name Mr./Mrs. Company Name Postal Address Postal code Phone Number E-mail Model Number of Product Serial Number of Product Purchase Date Distributor The material in this document is the intellectual property of our company. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without our company’s prior written permission. 1.
