QSD2014 User’s Manual Rev031309
INDEX Chapter 1： DVR Features .................................................................................................................................... 1 Chapter 2：Layout .................................................................................................................................................. 2 2.1 Front Panel..................................................................................................................................................... 2 2.
Chapter 7：Playback ............................................................................................................................................ 14 7.1 Playback Control ......................................................................................................................................... 14 Chapter 8： USB Program .................................................................................................................................. 15 8.1 Software Installation ...
QSD2014 User’s Manual Chapter 1： DVR Features DVR Features MPEG4 Compression; Video Input / Output：4-CH Video Input- 1-CH Video Output; Good Image quality, High definition; System Format: NTSC/PAL； Uses SOC chip with high stability; Linux operation System; Supports Multiple recording Modes: Continuous, Motion Detection, Time Schedule Supports Event List and Search/Playback by specified time; Supports Hidden Channel and Playback display; Missing Video signal Alarm Function; Password Pr
QSD2014 User’s Manual Chapter 2：Layout IR Receiver 2.1 Front Panel CH1 #1 Channel #1 Stop #10 Stop recording / playing CH2 #2 Channel #2 REC #11 Record CH3 #3 Channel #3 Menu/Esc #12 Enter / exit setup menu CH4 #4 Channel #4 SEL/Edit #13 Select / modify item Quad #5 Quad View Up #14 Move up Rewind/Move Left Down #15 Move down REW #6 Pause #7 Pause PWR #16 Power indicator LED Play #8 Play recorded video HDD #17 Hard drive indicator FWD #9 Forward/Move Right 2.
QSD2014 User’s Manual 2.
QSD2014 User’s Manual Chapter 3： DVR Installation 3.1 Hard Disk Installation Notice: Don’t take out the HDD when DVR is running. (1) Remove the top cover carefully; (2) Connect the power cord and data cable to hard drive; (3) Replace the top cover; 3.2 Connecting Camera and Monitor Attach the Camera cable to the DVR’s BNC video inputs, and DVR’s video output signal to Monitor’s video input jack respectively (refer to Chapter-2.2 Rear Panel shown) 3.
QSD2014 User’s Manual Chapter 4：Starting the DVR 4.1 Firmware version After turning on the unit, DVR will boot-up and display the current version and release date of the V2.X DVR firmware. V-EN-BG 2008.XX.XX 4.2 Detecting Installed Hard Drive During start up, DVR will automatically detect the installed hard drive and show the hard drive MASTER [MAXTOR STM3250310A] information. SLAVE…… 4.
QSD2014 User’s Manual Chapter 5： DVR Menu System 5.1 Browsing the Main Menu When start up is finished, please press [MENU] to MAIN MENU enter the Main Menu. CAMERA SETUP RECORD SETUP RECORD FRAMERATE VIDEO QUALITY RECORD SCHEDULE SENSOR SETUP HARD DRIVE SETUP MISCELLANEOUS SETUP RESET MENU ( HIGH ) MOVE (SEL) SELECT (MENU)EXIT 5.
QSD2014 User’s Manual Note：If a channel is disabled in Channel Setup, DVR will not record or set frame rate. 5.4 Record Setup Record Setup allows you to set up recording channels. 1 ON 2 NO Press [▲，▼，◄◄ and ►►] to select a channel, and then Record Setup press [SEL] to change the setting to on or off. If a channel is disabled in Camera Setup, it will not be recorded, and the characters “NOCAM” will be displayed 3 ON ( on screen. 4 ON ) MOVE (SEL) SELECT (MENU) ESC 5.
QSD2014 User’s Manual 5.7 Record Schedule Setting the Record Schedule allows you to customize the type of recording you want to use depending on the time of day. Record Schedule The time line indicates 24 hours of a day based on AM/PM (0=12). AM PM 0… 3… 6… 9… 0… 3…. 6… 9… Press [▲，▼，◄◄ and ►►] button s to select a time point, press [SEL] to modify the recording mode.
QSD2014 User’s Manual Area Selection：Press [▲，▼，◄◄ and ►►] buttons to select a block and then press [SEL] button to set the block to detect motion. The area is detectable when it is clear, the area is not detectable when it is covered by shadow. Press “Stop” button to disable all areas, and press “Quad” button to select all areas. 5.
QSD2014 User’s Manual 5.12 Miscellaneous Setup – Set Time The system date and time format is YYYY/MM/DD and HH:MM:SS. SET TIME Press [◄◄] or [►►] buttons to select a data, press [SEL] button to modify the data, and press [MENU] button to save 2008/11/11 17:50:01 ( and return to previous menu. ) MOVE (SEL) SELECT (MENU) ESC 5.13 Miscellaneous Setup – Hidden Channel Miscellaneous Setup in monitoring mode.
QSD2014 User’s Manual 5.15 Miscellaneous Setup – Password Enable Miscellaneous Setup When Password Enable is set to “on”, the CHANGE PASSWORD SET TIME HIDDEN CHANNEL [OFF] IMAGE PARAMETERS PASSWORD ENABLE KEYPAD TONES SEQ. DWELL TIME VIDEO LOSS SOUND [ CH1 ] [ OFF] [ ON ] [ 30 ] [ ON ] ( ) MOVE (SEL) SELECT (MENU) EXIT password will be required and must be entered correctly; otherwise, you will not be able to enter the system.
QSD2014 User’s Manual 5.19 RESET MENU System allows you to reset all your settings to the DVR factory default. You need to enter your password to reset the menu. 5.20 NTSC/PAL Output Select Change the jumper JS1 to select NTSC or PAL video output format shown on the silkscreen shown in the picture on the left. The picture shows the setting for PAL, move the jumper to the right side for NTSC Chapter 6：Record 6.
QSD2014 User’s Manual [●]：Indicates that the channel is being recorded. [A-REC]：Indicates the current record schedule is set to NORMAL-RECORD mode. [S-REC]：Indicates the current record schedule is set to SENSOR-RECORD mode. [N-REC]：Indicates the current record schedule is set to NO-RECORD mode. [39%]：Indicates the percentage of hard disk space used. [M]：HDD info ([M] MASTER HDD；[S] SLAVE HDD). 6.2 Audio Recording [ ]：indicates this video channel is assigned an audio port, and the audio output is on.
QSD2014 User’s Manual Chapter 7：Playback 7.1 Playback Control Press the [►] PLAY button to go into PLAYBACK mode. The newest recorded event will be played. SEACH VIDEO DISK: MASTER SLAVE [NONE] 08/09/19 11:16:31 - 08/09/19 15:05:48 TYPE: EVENT TIME PLAY： EVENT LIST 00006 T 2008/09/19 00006 T 2008/09/19 00006 T 2008/09/19 00006 T 2008/09/19 00006 T 2008/09/19 00006 T 2008/09/19 00006 T 2008/09/19 （ Press the [MENU] button in Playback mode， the system will list all the recorded events.
QSD2014 User’s Manual Chapter 8： USB Program 8.1 Software Installation Insert software CD to your CD-ROM drive; Open CD directory; Run “Installation” program; Follow the setup wizard to finish the installation. 8.2 Program Interface Button functions： NOTE: Since this DVR does not support PTZ cameras the functions marked as 1 and 2 will not work. 1. PTZ Control(NO Function) 2 Z i Z t 3. HDD Play Mode 4. FILE Play Mode 5. NET Play Mode 6. Event List 7. Program Local Setting 8. Remote DVR Control 9.
QSD2014 User’s Manual 10. Capture Image 20. Audio Slider 8.3 Program Running 8.3.1 HDD Play Mode System will detect HDD automatically when you connect DVR to your PC with USB cable. An icon “ ” will appear in the system tray (right bottom corner of the screen). After seeing this icon, double-click the “ ” icon on your desktop to run the program. Note: If you do not strictly follow above-mentioned steps, the program may fail to read recorded files.
QSD2014 User’s Manual Press the “ ” button to play video. 8.3.2 FILE Play Mode (Only when you have saved files to your PC.) Press the “ ” button to open a folder, select the file which you want to Play and double click to play video.
QSD2014 User’s Manual Chapter 9： Specification DVR Specification Items Descriptions Video Standard NTSC/PAL Video Input / Output 4-Channels /1Channels NTSC：720X480@30fps (Each CH) Resolution PAL：720X576@25fps (Each CH) Pre-view Features Full-D1, 1-Channel/4-Channel 1-channel Playback display NTSC：720X240@60fps (Total) Resolution PAL：720X288@50fps (Total) Recording Features Variable Frame Rate Quality 4 Level (Highest, High, Normal, Low) Video MPEG4 Compression Motion Detection Settable Det
QSD2014 User’s Manual Chapter 10：Appendix 10.1 System Connection Layout 10.
QSD2014 User’s Manual Q-See Product Warranty Thank you for choosing our products. All of our products users have a conditional free warranty repair service for hardware within 12 months starting from purchase date, and a free exchange service within one month (valid for manufacturing defects). Permanent upgrading service is provided for the software.
User Manual Customer Information Card User’s Name Mr./Mrs. Company Name Postal Address Postal code Phone Number E-mail Model Number of Product Serial Number of Product Purchase Date Distributor The material in this document is the intellectual property of our company. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without our company’s prior written permission. 1.
