Simplify SANbox2-8c Fibre Channel Switch Installation Guide 59042-00 A Page i
SANbox2-8c Fibre Channel Switch Installation Guide Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for illustrative purposes only.
Table of Contents Section 1 Introduction 1.1 1.2 1.3 1.4 1.5 1.6 1.6.1 1.6.2 1.6.4 1.6.5 1.6.6 1.6.7 1.7 1.8 1.9 1.10 1.11 1.11.1 1.11.2 1.11.3 Intended Audience ............................................................................................. 1-1 Related Materials ............................................................................................... 1-2 Safety Notices ....................................................................................................
SANbox2-8c Fibre Channel Switch Installation Guide 2.2.2 2.2.2.1 2.2.2.2 2.2.2.3 2.2.3 2.2.4 2.3 2.4 2.5 2.6 Port Modes ................................................................................................ 2-5 Fabric Ports ...................................................................................... 2-5 Expansion Port ................................................................................. 2-5 Translated Loop Port ............................................................
SANbox2-8c Fibre Channel Switch Installation Guide 4.2.4.1 4.2.4.2 4.2.4.3 4.2.5 4.2.5.1 4.2.5.2 4.2.6 4.2.7 4.2.8 4.2.9 4.3 4.3.1 4.3.2 4.3.3 SANbox Manager Installation for Windows ...................................... 4-7 SANbox Manager Installation for Linux ............................................ 4-8 SANbox Manager Installation for Solaris .......................................... 4-9 Connect the Management Workstation to the Switch.............................. 4-10 Ethernet Connection ...
SANbox2-8c Fibre Channel Switch Installation Guide Appendix B Command Line Interface B.1 B.2 B.3 Logging On to a Switch ......................................................................................B-1 Command Syntax...............................................................................................B-2 Commands .........................................................................................................B-3 Admin Command.....................................................
SANbox2-8c Fibre Channel Switch Installation Guide Index Figures Figure Page 2-1 SANbox2-8c Fibre Channel Switch................................................................................ 2-1 2-2 Chassis Controls and LEDS........................................................................................... 2-2 2-3 Fibre Channel Ports ....................................................................................................... 2-4 2-4 Ethernet Port ....................................
SANbox2-8c Fibre Channel Switch Installation Guide Notes Page viii 59042-00 A
Section 1 Introduction This manual is organized as follows: ■ Section 1 describes the intended audience, related materials, safety notices, communications statements, laser safety information, electrostatic discharge sensitivity precautions, accessible parts, and technical support. ■ Section 2 is an overview of the switch. It describes indicator LEDs and all user controls and connections. ■ Section 3 describes the factors to consider when planning a fabric.
1 – Introduction Related Materials 1.2 Related Materials The following manuals and materials are referenced in the text and/or provide additional information. ■ SANbox2 Switch Management User’s Guide, Publication Number 59022-03. Available from QLogic Corporation. ■ Fibre Channel-Arbitrated Loop (FC-AL-2) Rev. 6.8 ■ Fibre Channel-Private Loop SCSI Direct Attach (FC-PLDA) NCITS TR-19:1998 ■ Fibre Channel-10-bit Interface Rev. 2.
1 – Introduction Safety Notices 1.3 Safety Notices A Warning notice indicates the presence of a hazard that has the potential of causing moderate or minor personal injury. 4-3, 4-5 A Caution notice indicates the presence of a hazard that has the potential of causing damage to the equipment. 4-3 1.4 Sicherheitshinweise Ein Warnhinweis weist auf das Vorhandensein einer Gefahr hin, die möglicherweise mittelschwere oder leichte Verletzungen zur Folge hat.
1 – Introduction Communications Statements 1.6 Communications Statements The following statements apply to this product. The statements for other products intended for use with this product appear in their accompanying manuals. 1.6.1 Federal Communications Commission (FCC) Class A Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
1 – Introduction Communications Statements 1.6.4 CE Statement The CE symbol on the equipment indicates that this system complies with the EMC (Electromagnetic Compatibility) directive of the European Community (89/336/EEC) and to the Low Voltage (Safety) Directive (73/23/EEC). Such marking indicates that this system meets or exceeds the following technical standards: 59042-00 A ■ EN60950/A11:1997 – “Safety of Information Technology Equipment, Including Electrical Business Equipment”.
1 – Introduction Communications Statements 1.6.5 VCCI Class A Statement This is a Class A product based on the standard of the Voluntary Control Council For Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. 1.6.6 BSMI Class A Statement Warning: This is a Class A product.
1 – Introduction Electrostatic Discharge Sensitivity (ESDS) Precautions 1.6.7 Laser Safety Information This product may use Class 1 laser optical transceivers to communicate over the fiber optic conductors. The U.S. Department of Health and Human Services (DHHS) does not consider Class 1 lasers to be hazardous. The International Electrotechnical Commission (IEC) 825 Laser Safety Standard requires labeling in English, German, Finnish, and French stating that the product uses Class 1 lasers.
1 – Introduction Technical Support 1.11 Technical Support Customers should contact their authorized maintenance provider for technical support of their QLogic switch products. QLogic-direct customers may contact QLogic Technical Support; others will be redirected to their authorized maintenance provider. Visit the QLogic switch support Web site listed in ”Contact Information” on page 1-8 for the latest firmware and software updates. 1.11.
Section 2 General Description This section describes the features and capabilities of the SANbox2-8c Fibre Channel Switch. The following topics are described: ■ Chassis controls and LEDs ■ Fibre channel ports ■ Ethernet port ■ Serial port ■ Power supply and fan ■ Fabric management SANbox2 fabrics are managed with the SANbox Manager switch management application or the Command Line Interface (CLI). Refer to the SANbox2 Switch Management User’s Guide for information about using SANbox Manager.
2 – General Description Chassis Controls and LEDs 2.1 Chassis Controls and LEDs The Reset/Force PROM button shown in Figure 2-2 is the only chassis control and is used to recover a disabled switch. The chassis LEDs provide information about the switch’s operation status. These LEDS include the Over Temperature LED, Fan Fail LED, Heartbeat LED, and the Input Power LED. To apply power to the switch, plug the power cord into the switch AC power receptacle and into a 110 or 230 VAC power source.
2 – General Description Chassis Controls and LEDs 2.1.1.1 Resetting a Switch To reset the switch, use a pointed tool to press and release (less than 4 seconds) the Reset/Force PROM button. The switch will respond as follows: 1. All of the chassis LEDs will illuminate and then extinguish leaving only the Input Power LED illuminated. 2. After approximately 1 minute, the power-on self test begins illuminating all chassis LEDs. 3.
2 – General Description Fibre Channel Ports 2.1.4 Heartbeat LED (Yellow) The Heartbeat LED indicates the status of the internal switch processor and the results of the Power On Self Test (POST). Following a normal power-up, the Heartbeat LED blinks about once per second to indicate that the switch passed the POST and that the internal switch processor is running. In force PROM mode, the Heartbeat LED illuminates continuously.
2 – General Description Fibre Channel Ports 2.2.1 Small Form-Factor Pluggable (SFP) Transceivers SFP transceivers plug into the ports; duplex fiber optic cables plug into the transceivers which then connect to the devices. A port is capable of transmitting at 1 Gbps or 2 Gbps; however, the transceiver must be capable of 2 Gbps for the port to deliver at that rate. The SFP transceivers are hot swappable.
2 – General Description Fibre Channel Ports 2.2.2.3 Translated Loop Port A TL_Port supports a loop of up to 126 private devices with the ability to communicate with “off-loop” devices such as public fabric devices and private devices on other TL_Ports. TL_Ports connect to devices that conform to the Fibre Channel-Private Loop SCSI Direct Attach (FC-PLDA) standard. Devices connected to TL_Ports are registered with the Name Server. Use SANbox Manager or the CLI to explicitly configure a TL_Port.
2 – General Description Ethernet Port 2.2.4 Activity LED The Activity LED indicates that data is passing through the port. Each frame that enters or leaves the port causes this LED to illuminate for 50 milliseconds. This makes it possible to observe the transmission of a single frame. When extending credits, an Activity LED for a donor port will reflect the traffic of the recipient port. Refer to ”Distance” on page 3-6 for more information about extended credits and donor ports. 2.
2 – General Description Serial Port 2.4 Serial Port The SANbox2-8c switch is equipped with an RS-232 serial port for maintenance purposes as shown in Figure 2-5. You can manage the switch through the serial port using the CLI. 5 1 6 9 Serial Port Figure 2-5. Serial Port and Pin Identification The serial port connector requires a null-modem F/F DB9 cable. The pins on the switch RS-232 connector are shown in Figure 2-5 and identified in Table 2-1.
2 – General Description Power Supply and Fan 2.5 Power Supply and Fan The power supply converts standard 110 or 230 VAC to DC voltages for the various switch circuits. An internal fan provides cooling. Depending on the switch model, air flow is front-to-back or back-to-front. To energize the switch, plug the power cord into the switch AC receptacle and into a 110 or 230 VAC power source. Note: The power supply and fan are not field replaceable units. 2.
2 – General Description Switch Management Notes 2-10 59042-00 A
Section 3 Planning Consider the following when planning a fabric: ■ Devices ■ Multiple chassis fabrics ■ Performance ■ Device access ■ Fabric management ■ Fabric security 3.1 Devices When planning a fabric, consider the number of devices and the anticipated demand. This will determine the number of ports that are needed and in turn the number of switches. Consider how many and what types of switches are needed.
3 – Planning Multiple Chassis Fabrics 3.2 Multiple Chassis Fabrics By connecting switches together you can expand the number of available ports for devices. Each switch in the fabric is identified by a unique domain ID, and the fabric will automatically resolve domain ID conflicts. Because the ports are self-configuring, you can connect SANbox2 and other FC-SW-2 compliant switches together in a wide variety of topologies. 3.2.
3 – Planning Multiple Chassis Fabrics Note: Domain ID reassignment is not reflected in zoning that is defined by domain ID/port number pair or Fibre Channel address. You must reconfigure zones that are affected by domain ID reassignment. To prevent zoning definitions from becoming invalid, use the Set Config Switch command to lock the domain IDs. Refer to the ”Set Config Command” on page B-24. 3.2.
3 – Planning Multiple Chassis Fabrics 3.2.2.2 Mesh Topology A mesh topology describes a fabric in which each chassis has at least one port directly connected to each other chassis in the fabric. The example mesh fabric shown in Figure 3-2 has the following characteristics: ■ Each link contributes up to 200 MB/s of bandwidth between switches, 400 MB/s in full duplex. Because of multiple parallel paths, there is less competition for this bandwidth than with a cascade or a multistage topology.
3 – Planning Multiple Chassis Fabrics 3.2.2.3 Multistage Topology A multistage topology describes a fabric in which two or more edge switches connect to one or more core switches. Each additional core switch increases the bandwidth to each edge switch by 200 MB/s. The multistage fabric shown in Figure 3-3 has the following characteristics: ■ Each link contributes up to 200 MB/s of bandwidth between chassis.
3 – Planning Performance 3.3 Performance The SANbox2-8c switch supports class 2 and class 3 Fibre Channel service at transmission rates of 1 Gbps or 2 Gbps with a maximum frame size of 2148 bytes. A port can transmit or receive at 1 Gbps or 2 Gbps depending on the device to which it is connected. The port discovers the transmission speed prior to login when the connected device powers up. Related performance characteristics include the following: ■ Distance ■ Bandwidth ■ Latency 3.3.
3 – Planning Performance 3.3.2 Bandwidth Bandwidth is a measure of the volume of data that can be transmitted at a given transmission rate. A port can transmit or receive at 1 Gbps or 2 Gbps depending on the device to which it is connected. The switch supports all transmission rate combinations as shown in Table 3-1. Table 3-1.
3 – Planning Device Access 3.4 Device Access Consider device access needs within the fabric. Access is controlled by the use of zones and zone sets. Some zoning strategies include the following: ■ Separate devices that use different operating systems. ■ Separate devices that have no need to communicate with other devices in the fabric or have classified data. ■ Separate devices into department, administrative, or other functional group.
3 – Planning Device Access 3.4.1 Soft Zones Soft zoning divides the fabric for purposes of controlling discovery. Members of the same soft zone automatically discover and communicate freely with all other members of the same zone. The soft zone boundary is not secure; traffic across soft zones can occur if addressed correctly. Soft zones that include members from multiple switches need not include the ports of the inter-switch links. Soft zone boundaries yield to ACL and VPF zone boundaries.
3 – Planning Fabric Management 3.5 Fabric Management SANbox Manager and the CLI execute on a management workstation that provides for the configuration, control, maintenance of the fabric. Supported platforms include Windows, Solaris, and Linux. SANbox Manager can manage multiple fabrics. Consider how many fabrics will be managed, how many management workstations are needed, and whether the fabrics will be managed with the CLI or SANbox Manager.
Section 4 Installation This section describes how to install and configure the SANbox2-8c switch. It also describes how to load new firmware and how to recover a disabled switch. 4.1 Site Requirements The following items are required for the installation of a SANbox2-8c switch: ■ Fabric management workstation ■ Power requirements ■ Environmental conditions 4.1.1 Fabric Management Workstation SANbox Manager requires a management workstation equipped as described in Table 4-1: Table 4-1.
4 – Installation Installing a Switch 4.1.3 Environmental Conditions Consider the factors that affect the climate conditions in your facility such as heat dissipation and ventilation. The switch requires the following operating conditions: ■ Operating temperature range: 5 to 50°C (41 to 122°F) ■ Relative humidity: 15% to 80%, non-condensing 4.2 Installing a Switch Unpack the switch and accessories.
4 – Installation Installing a Switch Installing a SANbox2-8c switch involves the following steps: 1. Mount the switch 2. Install SFP transceivers 3. Connect the switch to the AC power source 4. Install SANbox Manager 5. Connect the management workstation to the switch 6. Set the date 7. Configure the switch 8. Configure the ports 9. Cable devices to the switch 4.2.1 Mount the Switch The switch can be placed on a flat surface and stacked or mounted in a 19” EIA rack.
4 – Installation Installing a Switch 4.2.2 Install SFP Transceivers The switch has been validated with transceivers that support a variety of interconnection media. To install, insert the transceiver into the port and gently press until it snaps in place as shown in Figure 4-2. To remove a transceiver, gently press the transceiver into the port to release the tension, then pull on the release tab or lever and remove the transceiver. Different transceiver manufacturers have different release mechanisms.
4 – Installation Installing a Switch 4.2.3 Connect the Switch to AC Power WARNING!! This product is supplied with a 3-wire power cord and plug for the user’s safety. Use this power cord in conjunction with a properly grounded outlet to avoid electrical shock. An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the Switch chassis. It is the responsibility of the customer to ensure that the outlet is correctly wired and grounded to prevent electrical shock.
4 – Installation Installing a Switch WARNUNG!! Dieses Produkt wird mit einem 3-adrigen Netzkabel mit Stecker geliefert. Dieses Kabel erfüllt die Sicherheitsanforderungen und sollte an einer vorschriftsmäßigen Schukosteckdose angeschlossen werden, um die Gefahr eines elektrischen Schlages zu vermeiden.Elektrosteckdosen, die nicht richtig verdrahtet sind, können gefährliche Hochspannung an den Metallteilen des Switch-Gehäuses verursachen.
4 – Installation Installing a Switch 4.2.4 Install SANbox Manager You can install SANbox Manager on the Windows, Linux, and Solaris platforms. Refer to the subsection that corresponds to your workstation: ■ 4.2.4.1 SANbox Manager Installation for Windows ■ 4.2.4.2 SANbox Manager Installation for Linux ■ 4.2.4.3 SANbox Manager Installation for Solaris 4.2.4.
4 – Installation Installing a Switch 4.2.4.2 SANbox Manager Installation for Linux To install the SANbox Manager application on Linux from the SANsurfer Tool Kit CD-ROM, do the following: 1. Close all programs currently running, and insert the SANsurfer Tool Kit CD into the management workstation CD-ROM drive. If a file browser window opens showing icons for the contents of the CD-ROM, double-click the Start_Here.htm file to open the SANsurfer Tool Kit start page.
4 – Installation Installing a Switch 4.2.4.3 SANbox Manager Installation for Solaris To install the SANbox Manager application on Solaris from the SANsurfer Tool Kit CD-ROM, do the following: 1. Close all programs currently running, and insert the SANsurfer Tool Kit CD into the management workstation CD-ROM drive. If the SANsurfer Tool Kit start page does not open in your default browser, do the following: a. Right-click the to open the Workspace Menu. b.
4 – Installation Installing a Switch 4.2.5 Connect the Management Workstation to the Switch Connect the management workstation to the switch in one of three ways: ■ Indirect Ethernet connection from the management workstation to the switch RJ-45 Ethernet connector through an Ethernet switch or a hub. This requires a 10/100 Base-T straight cable as shown in Figure 4-3. With this method, you can manage the switch with SANbox Manager or the CLI.
4 – Installation Installing a Switch 4.2.5.1 Ethernet Connection To establish an Ethernet connection, do the following: 1. Connect a 10/100 Base-T cross-over cable from a COM port on the management workstation directly to the RJ-45 Ethernet port; or a 10/100 Base-T straight cable indirectly over an Ethernet network. 2. Open a command line window. 3. Open a Telnet session by entering the following command with the switch IP address. The default IP address is 10.0.0.1 telnet 10.0.0.1 4.
4 – Installation Installing a Switch ■ For Linux: a. Set up minicom to use the serial port. Create or modify the /etc/minirc.dfl file with the following content: pr pu pu pu portdev/ttyS0 minit mreset mhangup b. Verify that all users have permission to run minicom. Review the /etc/minicom/users file and confirm that the line "ALL" exists or that there are specific user entries. c. Enter the following command at the Linux prompt: minicom ■ For Solaris: a. Set up Solaris to use the serial port.
4 – Installation Installing a Switch 2. Enter the Date command and parameters (MMDDhhmmCCYY format) to set the system date on the switch. SANbox2 (admin) $> date 083007512002 3. To reset the switch, enter the following command and press the Enter key. SANbox2 (admin) $> reset switch 4.2.7 Configure the Switch Do the following to configure a switch using the SANbox Manager application.
4 – Installation Loading Firmware 4.2.8 Configure the Ports Configuring a port involves defining the port mode and setting the frame sequencing if necessary. For public devices and other switches, a switch automatically sets the port mode as each port discovers the type of device to which it is connected. A GL_Port will self configure as an FL_Port when connected to a loop of public devices or an F_Port when connected to a single device.
4 – Installation Loading Firmware 3. Establish communications with the switch using the File Transfer Protocol (FTP). Enter one of the following on the command line: >ftp xxx.xxx.xxx.xxx or >ftp switchname where xxx.xxx.xxx.xxx is the switch IP address and switchname is the switch name associated with the IP address. 4. Enter the following account name and password: user:images password:images 5. Activate binary mode and copy the firmware image file (filename.
4 – Installation Loading Firmware 4.3.2 Using SANbox Manager to Load Firmware To load the firmware using SANbox Manager, do the following: 1. From the Faceplate display, open the Switch menu and select Load Firmware. 2. In the Firmware Upload window, browse and select the firmware file you want to load. 3. In the Firmware Upload window, choose the Start button to begin the loading process.
4 – Installation Loading Firmware 4. Enter the following command to display the list of firmware files: SANbox2 (admin) #> image list firmwarefilenameonswitch 5. Enter the following command to install the new firmware: SANbox2 (admin) #>image unpack firmwarefilenameonswitch 6. Reset the switch to activate the new firmware.
4 – Installation Loading Firmware Notes 4-18 59042-00 A
Section 5 Diagnostics/Troubleshooting Diagnostic information about the switch is available through the chassis LEDs and the port LEDs. Diagnostic information is also available through the SANbox Manager and CLI event logs and error displays. This section describes two types of diagnostics: Power On Self Test (POST) and chassis. POST diagnostics describe the Heartbeat LED and the port Logged-In LED indications.
5 – Diagnostics/Troubleshooting POST Diagnostics 5.1.1.2 Force PROM Mode Pattern Steady illumination indicates that the switch is in force PROM mode, which returns the switch IP address to 10.0.0.1. From force PROM mode, you may reload firmware, reset the password to the factory default, and remove a corrupt configuration. 5.1.1.3 Internal Firmware Failure Blink Pattern An internal firmware failure blink pattern is 2 blinks per second followed by a two second pause.
5 – Diagnostics/Troubleshooting POST Diagnostics 5.1.2 Logged-In LED Indications Port diagnostics are indicated by the Logged-In LED for each port as shown in Figure 5-1. Logged-In LED Figure 5-1. Port Logged-In LED The Logged-In LED has three indications: ■ Logged in - Continuous illumination. ■ Logging in - Flashes at roughly once per second as shown in Figure 5-2. ■ Error - Flashes at roughly twice per second as shown in Figure 5-2. 1 second Logging In Error Figure 5-2.
5 – Diagnostics/Troubleshooting POST Diagnostics A Logged-In LED error indication is often the result of E_Port isolation. An isolated E_Port is indicated by a red link in the topology display. Table 5-1 describes the causes and remedies for E_Port isolation conditions. Table 5-1. E_Port Isolation Causes and Remedies Isolation Cause Remedy Two switches in the same fabric have the same domain ID Correct the domain IDs on the offending switches. Domain IDs must be unique.
5 – Diagnostics/Troubleshooting Chassis Diagnostics 5.2 Chassis Diagnostics Chassis diagnostics are indicated by the chassis LEDs as shown in Figure 5-3. Over Temperature LED (Yellow) Fan Fail LED (Yellow) Input Power LED (Green) Heartbeat LED (Yellow) Figure 5-3. Chassis LEDs The following conditions are described: ■ Over Temperature LED is illuminated ■ Input Power LED is extinguished ■ Fan Fail LED is illuminated 5.2.
5 – Diagnostics/Troubleshooting Recovering a Switch 5.2.2 Input Power LED Is Extinguished The Input Power LED illuminates to indicate that the switch logic circuitry is receiving proper voltages. If the Input Power LED is extinguished, do the following: 1. 2. Inspect the power cords and connectors. Is the cord unplugged? Is the cord or connector damaged? ■ Yes - Make necessary corrections or repairs. If the condition remains, continue. ■ No - Continue. Inspect the AC power source.
5 – Diagnostics/Troubleshooting Recovering a Switch To recover a switch, do the following: 1. Connect a workstation to the switch through the Ethernet connector. Refer to ”Connect the Management Workstation to the Switch” on page 4-10. 2. Before a switch can be recovered, you must upload the firmware to the switch. Refer to ”Loading Firmware” on page 4-14 for instructions on loading firmware using the SANbox Manager and using the File Transfer Protocol method.
5 – Diagnostics/Troubleshooting Recovering a Switch ■ Choose the Reset Password File option to restore the default account name and password (Admin, Password). ■ Choose the Copy Log Files option to copy the log file ■ Choose the Remove Switch Config option to delete a corrupt configuration. This will reset the factory defaults for the switch, except for account names and passwords. ■ Choose the Remake Filesystem option to reset the entire switch to the factory default settings.
Appendix A Specifications Appendix A contains the specifications for the SANbox2-8c Fibre Channel Switch. Refer to Section 2 General Description for the location of all connections, switches, and components. A.1 Switch Specifications Fibre Channel Protocols ................. FC-PH Rev. 4.3 FC-PH-2 FC-PH-3 FC-AL Rev 4.5 FC-AL-2 Rev 7.0 FC-FLA FC-GS-2 FC-FG FC-PLDA FC-Tape FC-VI FC-SW-2 Fabric Element MIB RFC 2837 Fibre Alliance MIB Version 3.0 Fibre Channel Classes of Service ..
A – Specifications Switch Maintainability Media Type ..................................... Small Form Pluggable (SFP), 3.3 volt, optical transceivers. Hot swappable. Fabric Port Speed ........................... 1.0625 or 2.125 Gigabits/second Maximum Frame Size..................... 2148 bytes (2112 byte payload) System Processor........................... 266 MHz Pentium® processor Fabric Latency (best case) ............. <0.5 µsec. Fabric Point-to-Point Bandwidth .....
A – Specifications Switch Dimensions A.4 Switch Dimensions Width............................................... 8.5” Height ............................................. 1.70” Depth .............................................. 20.0” Weight............................................. 8.5 lbs. A.5 Switch Electrical Operating voltage ........................... 90 to 137 Vac; 47 to 63 Hz 180 to 264 Vac; 47 to 63 Hz Power source loading ..................... 1.0 Amps maximum at 90 to 137 Vac 0.
A – Specifications Switch Regulatory Certifications A.7 Switch Regulatory Certifications Safety Standards ............................ UL60950, CSA 22.2 No. 60950, EN60950 Emissions Standards ...................... FCC Part 15B Class A VCCI Class A ITE BSMI Class A ICES-03 Issue 3 CISPR 22, Class A EN 55022, Class A Voltage Fluctuations ....................... EN 61000-3-3 Harmonics....................................... EN 61000-3-2 Immunity .........................................
A – Specifications Longwave Laser SFP 1G/2G (single-mode) A.9 Longwave Laser SFP 1G/2G (single-mode) Connector ....................................... Duplex LC Color coding.................................... Blue exposed connector surfaces Cable .............................................. Fibre Channel 100SM-LC-L (9 µm single mode) Wavelength..................................... 1270 - 13.5 nm Transmit Power............................... -10 dBm minimum Receiver Sensitivity ......................
A – Specifications Longwave Laser SFP 1G/2G (single-mode) Notes A-6 59042-00 A
Appendix B Command Line Interface Each SANbox2 switch contains a Telnet server. This server allows a Telnet client to establish a Telnet session with the switch to retrieve information or to configure parameters. The Command Line Interface (CLI) enables you to perform a variety of fabric and switch management tasks through an Ethernet or a serial port connection to a switch. B.
B – Command Line Interface Command Syntax B.2 Command Syntax The command syntax is as follows: command keyword keyword [value] keyword [value1] [value2] The Command is followed by one or more keywords. Consider the following rules and conventions: B-2 ■ Commands and keywords are lowercase and case sensitive. ■ Commands with keywords require one of those keywords. ■ Required keyword values appear in standard font: [value]. Optional values are shown in italics: [value].
B – Command Line Interface Commands B.3 Commands The Command Line Interface provides for User and Admin authority levels. ■ User authority grants viewing access to the fabric and switches using the Show command and other read-only commands. ■ Admin authority includes the User authority and grants permission to use the Admin command. The Admin Start command opens an admin session which provides access to the commands that change switch and fabric configurations.
B – Command Line Interface Admin Command Admin Command Opens and closes an Admin session granting Admin authority. The Admin session provides commands that change the fabric and switch configurations. Only one Admin session can be open in the fabric at any time. An inactive Admin session will time out after a period of time which can be changed using the Set Setup System command. Refer to the ”Set Setup Command” on page B-34.
B – Command Line Interface Alias Command Alias Command Creates a named set of ports. Aliases make it easier to assign a set of ports to many zones. An alias can not have a zone or another alias as a member.
B – Command Line Interface Alias Command remove [alias] [members] Removes the ports given by [members] from the alias given by [alias]. [members] can have one of the following formats: ■ Domain ID and port number pair (Domain ID, Port Number). Domain IDs and port numbers are in decimal. Ports are numbered beginning with 0. ■ 6-character device Fibre Channel address (hex) ■ 16-character hexadecimal worldwide port name (WWPN) for the device with the format xx:xx:xx:xx:xx:xx:xx:xx.
B – Command Line Interface Config Command Config Command Manages the Fibre Channel configurations on a switch. For information about setting the port and switch configurations, refer to the ”Set Config Command” on page B-24. Authority Admin for all keywords except List Syntax config activate [config] backup cancel copy [config_source] [config_destination] delete [config] edit [config] list restore save [config] Keywords activate [config] Activates the configuration given by [config].
B – Command Line Interface Config Command restore Restores configuration settings to the switch from a backup file named configdata, which must be first uploaded on the switch using FTP. You create the backup file using the Config Backup command. Use FTP to load the backup file on a switch, then enter the Config Restore command. save [config] Saves changes made during a configuration edit session in the configuration given by [config].
B – Command Line Interface Date Command Date Command This command displays or sets the system date and time. To set the date and time the information string must be provided in this format: MMDDhhmmCCYY Authority Admin Syntax date [MMDDhhmmCCYY] Keywords [MMDDhhmmCCYY] Specifies the date. If you omit the keyword value, the current date is displayed.
B – Command Line Interface Fallback Command Fallback Command Loads the fallback version of the firmware from switch memory. The switch stores two versions of the firmware. This command alternately activates the two versions. Authority Admin Syntax Notes fallback Examples ■ The Show Switch command displays the available firmware versions and the currently active version. ■ After executing the Fallback command, reset the switch for the firmware to placed in effect.
B – Command Line Interface Help Command Help Command Displays a brief description of the specified command and its keywords. Authority User Syntax Keywords help [command] [keyword] [command] A command name. If you omit this value, the system displays all available commands from which to choose. [keyword] A keyword associated with the command named by [command]. If you omit this value, the system displays the available keywords for the specified command.
B – Command Line Interface History Command History Command Displays a numbered list of the previously entered commands from which you can re-execute selected commands. Authority User Syntax Notes history Examples Use the History command to provide context for the ! command: ■ Enter ![command] to re-enter the most recent execution of that command.
B – Command Line Interface Image Command Image Command Manages and installs switch firmware. Authority Admin Syntax image cleanup fetch [account_name] [ip_address] [file_source] [file_destination] list unpack [file] Keywords cleanup Removes the firmware image file from the switch. The firmware image file is removed automatically each time the switch is reset.
B – Command Line Interface Lip Command Lip Command Reinitializes the specified loop port. Authority Admin Syntax Keywords lip [port_number] Examples The following is an example of the Lip command: [port_number] The number of the port to be reinitialized.
B – Command Line Interface Passwd Command Passwd Command Changes a user account’s password. Authority Admin Syntax Keywords passwd [account_name] Examples The following is an example of the Passwd command: [account_name] The user account name. SANbox2 (admin) #> passwd user2 Press ’q’ and the ENTER key to abort this command. account OLD password : account NEW password (4-20 chars) : please confirm account NEW password: password has been changed.
B – Command Line Interface Ps Command Ps Command Displays current system process information. Authority User Syntax Examples ps The following is an example of the Ps command: SANbox2 $> ps PID B-16 PPID %CPU TIME ELAPSED COMMAND 298 292 0.0 00:00:00 59:42 cns 299 292 0.0 00:00:00 59:42 ens 300 292 0.0 00:00:00 59:42 dlog 301 292 0.3 00:00:53 59:42 ds 302 292 0.2 00:00:29 59:42 mgmtApp 303 292 0.0 00:00:02 59:42 nserver 304 292 0.0 00:00:00 59:42 mserver 305 292 0.
B – Command Line Interface Quit Command Quit Command Closes the Telnet session.
B – Command Line Interface Reset Command Reset Command Resets the switch and port configuration parameters. Authority Admin Syntax reset config factory port [port_number] snmp switch (default) system zoning Keywords config Resets the configuration settings for the switch and its ports to the factory default values. Refer to Table B-2 and Table B-3 for switch and port configuration default values. factory Resets switch, port, SNMP, and system configuration settings to the factory default values.
Notes B – Command Line Interface Reset Command The following tables specify the various factory default settings: Table B-2. Switch Configuration Defaults Parameter Default Admin State Online Broadcast Enable False Domain ID 1 Domain ID Lock True Symbolic Name SANbox2 R_T_TOV 100 R_A_TOV 10000 E_D_TOV 2000 FS_TOV 5000 DS_TOV 5000 Principal Priority 254 Description Undefined Table B-3.
B – Command Line Interface Reset Command Table B-3. Port Configuration Defaults (Continued) Parameter Default LCFEnable False MFSEnable False MFS_TOV 640 MSEnable True NoClose False IOStreamGuard False VIEnable False CheckAlps False Table B-4. SNMP Configuration Defaults Parameter B-20 Default Contact Undefined Location Undefined Description Undefined Trap [1-5] Enabled False Trap [1-5] Address 127.0.0.
B – Command Line Interface Reset Command Table B-5. System Configuration Defaults Parameter 59042-00 A Default Network IP Address 10.0.0.1 Network IP Mask 255.0.0.0 Gateway Address 10.0.0.
B – Command Line Interface Set Alarm Clear Command Set Alarm Clear Command Clears the log (list) of alarms. Authority User Syntax Examples set alarm clear The following example clears the list of alarms.
B – Command Line Interface Set Beacon Command Set Beacon Command Assists in locating a switch by causing all port Logged-In LEDs on the switch to flash. Authority User Syntax Keywords set beacon [state] [state] Enables or disables the flashing of the port Logged-In LEDs according to [state]. On Enables the flashing beacon. Off Disables the flashing beacon. Examples The following examples enables and disables the beacon: SANbox2 $> set beacon on Command succeeded.
B – Command Line Interface Set Config Command Set Config Command Sets switch, port, and zoning configuration parameters. Authority Admin authority within a Config Edit session Syntax set config port [port_number] ports [port_number] switch zoning Keywords port [port_number] Changes configuration parameters for the port number given by [port_number]. If you omit this value, the system begins with port 0 and proceeds in order through port 15 or until you enter “qq”.
B – Command Line Interface Set Config Command Table B-6. Set Config Port Parameters (Continued) Parameter 59042-00 A Description ISLSecurity E_Port security. Determines which switches a port will establish a link with. ■ ANY - we will link with any switch. ■ Ours - we will only link to another SANbox2 switch. ■ None - the port will not establish an ISL link.
B – Command Line Interface Set Config Command switch Initiates an editing session in which to change switch configuration settings. The system displays each parameter one line at a time and prompts you for a value. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. Table B-7. Set Config Switch Parameters Parameter B-26 Description AdminState Switch administrative state: online, offline, or diagnostics.
B – Command Line Interface Set Config Command zoning Initiates an editing session in which to change switch zoning attributes. The system displays each parameter one line at a time and prompts you for a value. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. Table B-8.
B – Command Line Interface Set Config Command ARB_FF (True / False) [False ] InteropCredit (decimal value, 0-255) [0 ] ExtCredit (decimal value, 0-65535) [0 ] FANEnable (True / False) [True ] LCFEnable (True / False) [False ] MFSEnable (True / False) [False ] MFS_TOV (decimal value, 10-20480 msec) [640 ] MSEnable (True / False) [True ] NoClose (True / False) [False ] I/O Stream Guard (Suppress RSCN)(Enable / Disable) [Disable] VIEnable (True / False) [False ] CheckAlp
B – Command Line Interface Set Config Command The following is an example of the Set Config Zoning command. SANbox2 $> admin start SANbox2 (admin) #> config edit SANbox2 (admin-config) #> set config zoning A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the default value. If you wish to terminate this process before reaching the end of the list press ’q’ or ’Q’ and the ENTER key to do so.
B – Command Line Interface Set Log Command Set Log Command Specifies the type of entries to be entered in the event log. The log is a storage file contained on the switch. The log can hold a maximum of 200 entries. When the log becomes full, the entries are replaced, starting with the oldest entry, to produce a list of the last 200 events which occurred. Log entries are created for ports, components, and event severity levels, based on the settings defined for the active configuration.
B – Command Line Interface Set Log Command None Monitor none of the component events. Other Monitors other miscellaneous events. Port Monitors all port events Switch Monitors switch management events. Zoning Monitors zoning conflict events. level [level] Specifies the severity level given by [level] to use in monitoring events for the specified components or ports. [level] can be one of the following values: Critical Monitors critical events. Warn Monitors warning events.
B – Command Line Interface Set Log Command start Starts the logging of events based on the Port, Component, and Level keywords assigned to the active configuration. The logging continues until you enter the Set Log Stop command. stop Stops logging of events. Notes B-32 To maintain optimal switch performance, do not set the Component keyword to All and the Level keyword to Info at the same time.
B – Command Line Interface Set Port Command Set Port Command Sets port state and speed for the specified port temporarily until the next switch reset or new configuration activation. This command also clears port counters. Authority Admin Syntax set port [port_number] bypass clear enable speed [transmission_speed] state [admin_state] Keywords [port_number] Specifies the port. Ports are numbered beginning with 0.
B – Command Line Interface Set Setup Command Set Setup Command Changes SNMP and system configuration settings. The switch maintains one SNMP configuration and one system configuration. Authority Admin Syntax set setup snmp system Keywords snmp Prompts you in a line-by-line fashion to change SNMP configuration settings. Table B-9 describes the SNMP fields. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. Table B-9.
B – Command Line Interface Set Setup Command system Prompts you in a line-by-line fashion to change system configuration settings. Table B-10 describes the system configuration fields. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. Table B-10. System Configuration Settings Entry Notes 59042-00 A Description NetworkIPAddress Internet Protocol (IP) address for the Ethernet port. NetworkIPMask Subnet mask address for the Ethernet port.
B – Command Line Interface Set Setup Command Examples The following is an example of the Set Setup SNMP command: SANbox2 $> admin start SANbox2 (admin) #> set setup snmp A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the default value. If you wish to terminate this process before reaching the end of the list press ’q’ or ’Q’ and the ENTER key to do so.
B – Command Line Interface Set Setup Command The following is an example of the Set Setup System command: SANbox2 $> admin start SANbox2 (admin) #> set setup system A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the default value. If you wish to terminate this process before reaching the end of the list press ’q’ or ’Q’ and the ENTER key to do so. NetworkIPAddress (dot-notated IP Address) [172.22.10.
B – Command Line Interface Set Switch Command Set Switch Command Temporarily changes the administrative state for all ports on the switch. The previous Set Config Switch settings are restored after a switch reset or a reactivation of a switch configuration. Authority Admin Syntax set switch state [admin_state] Keywords state [admin_state] Specifies the administrative state as given by [admin_state]: Online Places all ports online Offline Places all ports offline.
B – Command Line Interface Show Command Show Command Displays fabric, switch, and port operational information. Authority User Syntax show about alarm broadcast chassis config [option] domains donor fabric intro log [option] lsdb mem [count] ns perf [option] port [port_number] setup [option] steering [domain_id] switch topology users Keywords about Displays an introductory set of information about operational attributes of the switch. It is functionally equivalent to the Show Intro command.
B – Command Line Interface Show Command fabric Displays list of each domain, fabric ID, worldwide name, node IP address, port IP address, and symbolic name in the fabric. intro Displays an introductory set of information about operational attributes of the switch. It is functionally equivalent to the Show About command. log [option] Displays log entries. Refer to the ”Show Log Command” on page B-50. lsdb Displays Link State database information.
B – Command Line Interface Show Command Table B-11. Show Port Parameters (Continued) Entry 59042-00 A Description FBusy Number of times the switch sent a P_BSY because Class 2 frame could not be delivered within ED_TOV time. Number of class 2 and class 3 fabric busy (F_BSY) frames generated by this port in response to incoming frames. This usually indicates a busy condition on the fabric or N_port that is preventing delivery of this frame.
B – Command Line Interface Show Command Table B-11. Show Port Parameters (Continued) Entry B-42 Description Logout Time when user logged out. LoopTimeouts A two (2) second timeout as specified by FC-AL-2. LossOfSync Number of synchronization losses (>100 ms) detected by this port. A loss of synchronization is detected by receipt of an invalid transmission word. PrimSeqErrors Primitive sequence errors detected. RxLinkResets Number of link reset primatives received from an attached device.
B – Command Line Interface Show Command setup [option] Displays setup attributes for the system, SNMP, and the switch manufacturer. Refer to the ”Show Setup Command” on page B-53. steering [domain_id] Displays the routes that data takes to the switch given by [domain_id]. If you omit [domain_id], the system displays routes for all switches in the fabric. switch Displays switch operational information. topology Displays all connected devices. users Displays all user logins.
B – Command Line Interface Show Command The following is an example of the Show Fabric command: SANbox2 $> show fabric Switch ID WWN NodeIPAddress PortIPAddress SymbolicName ------ ---------------- ------------- -----------100 fffc64 10:00:00:60:69:20:4c:a2 103 fffc67 10:00:00:c0:dd:00:b9:09 104 fffc68 10:00:00:c0:dd:00:b8:4b The following is an example of the Show Setup SNMP command: SANbox2 $> show setup snmp SNMP Information ---------------- B-44 Contact Technical Support Location TSLab D
B – Command Line Interface Show Command The following is an example of the Show Topology command: SANbox2 $> show topology Unique ID Key ------------A = ALPA, Port D = Domain ID, P = Port ID Local Local Number Type PortWWN ------ ----- ------- Remote Remote Unique Type ID NodeWWN ------ ------- ------ 0 E 20:00:00:c0:dd:00:c2:d6 E 10:00:00:c0:dd:00:b9:fd 1(0x1) D 1 F 20:01:00:c0:dd:00:c2:d6 N 50:00:60:e8:02:a0:f8:16 020100 P 2 F 20:02:00:c0:dd:00:c2:d6 N 20:00:00:e0:8b:05:0f:6
B – Command Line Interface Show Command The following is an example of the Show Port command: SANbox2 $> show port 3 Port Number: 3 -------------- B-46 AdminState Online OperationalState Offline AsicNumber 1 PortID 050300 AsicPort 3 PortWWN 20:03:00:c0:dd:00:90:6b ConfigType GL RunningType Unknown DiagStatus Passed SFPPartNumber Unknown EpConnState None SFPRevision 0 EpIsoReason NotApplicable SFPType NotInstalled LinkSpeed Auto SFPVendor Unknown LinkState Inactive SFP
B – Command Line Interface Show Command The following is an example of the Show Switch command: SANbox2 $> show switch Switch Information ------------------ 59042-00 A SymbolicName SANbox2 SwitchWWN 10:00:00:c0:dd:00:c2:d6 SwitchType Sanbox2-8 PROMVersion V0.4-0-0 CreditPool 0 DomainID 2 (0x2) FlashSize - MBytes 128 LogLevel Critical MaxPorts 8 NumberOfAsics 1 NumberOfPortsPerAsic 16 NumberOfResets 11 ReasonForLastReset NormalReset SWImageVersion (1) - build date V1.
B – Command Line Interface Show Config Command Show Config Command Display switch and port attributes for the active configuration. Authority User Syntax show config port [port_number] switch zoning Keywords port [port_number] Displays configuration parameters for the port number given by [port_number]. Ports are numbered beginning with 0. If the port value is omitted, all ports are specified. switch Displays configuration parameters for the switch.
B – Command Line Interface Show Config Command VIEnable False CheckAlps False The following is an example of the Show Config Switch command: SANbox2 $> show config switch Configuration Name: default ------------------- Switch Configuration Information -------------------------------AdminState Online BroadcastEnable False DomainID 11 DomainIDLock True SymbolicName bottom switch R_T_TOV 100 R_A_TOV 10000 E_D_TOV 2000 FS_TOV 5000 DS_TOV 5000 PrincipalPriority 254 Description Th
B – Command Line Interface Show Log Command Show Log Command Displays the contents of the log or the parameters used to create entries in the log. The log contains a maximum of 200 entries. When the log reaches its entry capacity, subsequent entries overwrite the existing entries, beginning with the oldest. Authority User Syntax show log component level options port settings Keywords component Displays the components currently being monitored for events.
B – Command Line Interface Show Log Command The following is an example of the Show Log Options command: SANbox2 $> show log options Allowed options for ’ level’: Critical,Warn,Info,None Allowed options for ’component’: All,None,NameServer,MgmtServer,Zoning,Switch, Chassis,Blade,Port,Eport,Snmp,Other The following is an example of the Show Log command: [327][Wed Jan 25 09:36:54.860 1989][I][Eport:0xdd00b8b6.304.4 Port: 0/8][Eport State = E_A0_GET_DOMAIN_ID] [328][Wed Jan 25 09:36:54.
B – Command Line Interface Show Perf Command Show Perf Command Displays performance data for all ports. Authority User Syntax show perf byte [bytes/sec] frame [frames/sec] Keywords byte [bytes/sec] Displays port performance data for all ports in bytes/second. The display is refreshed according to the interval in seconds given by [bytes/sec]. If [bytes/sec] is omitted, the display is refreshed every second. Type “q” and press the Enter key to stop the display.
B – Command Line Interface Show Setup Command Show Setup Command Displays the current SNMP and system settings. Authority User Syntax show setup snmp system Keywords snmp Displays the current SNMP settings. system Displays the current system settings.
B – Command Line Interface Show Setup Command The following is an example of the Show Setup System command: SANbox2 $> show setup system System Information ------------------ B-54 NetworkIPAddress 172.22.11.202 NetworkIPMask 255.255.252.0 GatewayIPAddress 172.22.8.
B – Command Line Interface Shutdown Command Shutdown Command Terminates all data transfers on the switch at convenient points and closes the Telnet session.
B – Command Line Interface Test Command Test Command Performs the port loopback test to verify the operation of a port. The three types of loopback tests are Internal (SerDes level), External (SFP), and Online. While the test is running, the remaining ports on the switch remain fully operational. Authority Admin Syntax Keywords test [port_number] [test_type] [port_number] Specifies the port. Ports are numbered beginning with 0. [test_type] The test type.
B – Command Line Interface Test Command 5. After the test type has been chosen and the command executed, a message on the screen will appear detailing the test results. 6. After the test is run, put the port back into online state by entering the following command (x = port number) and pressing the Enter key. set port x state online 7. To verify port is back online, enter the following command and press the Enter key. The contents of the AdminState field should display be “Online”.
B – Command Line Interface Uptime Command Uptime Command Displays the elapsed time since the switch was last reset and reset method.
B – Command Line Interface User Command User Command Administers or displays user accounts. Authority Admin Syntax user accounts add delete [account_name] list Keywords accounts Displays all user accounts that exist on the switch. add Add a user account to the switch. After this command is executed, the administrator will be prompted for the information needed to establish the user account. delete [account_name] Deletes the account name given by [account_name] from the switch.
B – Command Line Interface User Command OK to add user account ’user3’ with admin authority? Please confirm (y/n): [n] y The following is an example of the User Delete command: SANbox2 (admin) #> user del user3 The user account will be deleted.
B – Command Line Interface Whoami Command Whoami Command Displays the account name, session number, and switch domain ID for the Telnet session.
B – Command Line Interface Zone Command Zone Command Manages zones and zone membership on a switch. The Zone command defines members (ports and devices) for a single switch. Zones are members of zone sets. Authority Admin authority within a Zoning Edit session. Refer to the ”Zoning Command” on page B-67. List, Members, and zone sets keywords are available with User authority and do not require a Zoning Edit session.
B – Command Line Interface Zone Command list Displays a list of all zones and the zone sets of which they are members. This keyword is valid for User authority and does not require a zoning edit session. members [zone] Displays all members of the zone given by [zone]. This keyword is available with User authority and does not require a Zoning Edit session. remove [zone] [members] Removes the ports given by [members] from the zone given by [zone].
B – Command Line Interface Zone Command zone_set_1 wwn_221416 zone_set_1 wwn_2215c3 zone_set_1 wwn_0160ed zone_set_1 wwn_c001b0 zone_set_1 wwn_401248 zone_set_1 wwn_02402f zone_set_1 wwn_22412f zone_set_1 The following is an example of the Zone Members command: SANbox2 $> zone members wwn_b0241f Current List of Members for Zone: wwn_b0241f --------------------------------50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 21:00:00:e0:8b:02:41:2f The following is an example of the Zone Zonesets com
B – Command Line Interface Zoneset Command Zoneset Command Manages zone sets and zone set membership across the fabric. Authority Admin authority within a Zoning Edit session. Refer to the ”Zoning Command” on page B-67. Active, List, Zones keywords are available with User authority. You must close the Zoning Edit session before using the Activate and Deactivate keywords.
B – Command Line Interface Zoneset Command list Displays a list of all zone sets. This keyword is available with User authority and does not require a Zoning Edit session. remove [zone_set] [zone_list] Removes one or more zones given by [zone_list] from the zone set given by [zone_set]. If [zone_set] is the active zone set, the zone will not removed until the zone set has been deactivated. [zone_list] can be an alias. This keyword requires a Zoning Edit session.
B – Command Line Interface Zoning Command Zoning Command Opens a Zoning Edit session in which to create and manage zone sets and zones. Refer to the ”Zone Command” on page B-62 and the ”Zoneset Command” on page B-65. Authority Admin. The List keyword is available with User authority. Syntax zoning cancel clear edit list restore save Keywords cancel Closes the current Zoning Edit session. Any unsaved changes are lost.
B – Command Line Interface Zoning Command Examples The following is an example of the Zoning Edit command: SANbox2 $> admin start SANbox2 (admin) #> zoning edit SANbox2 (admin-zoning) #> . . SANbox2 (admin-zoning) #> zoning cancel Zoning edit mode will be canceled.
B – Command Line Interface Zoning Command Configured Zoning Information ZoneSet Zone ZoneMember -------------------------------wwn wwn_b0241f 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 21:00:00:e0:8b:02:41:2f wwn_23bd31 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:23:bd:31 wwn_221416 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:14:16 wwn_2215c3 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:15:c3 59042-00 A B-69
B – Command Line Interface Zoning Command Notes B-70 59042-00 A
Glossary Activity LED A port LED that indicates when frames are entering or leaving the port. Class 3 Service A service which multiplexes frames at frame boundaries to or from one or more N_Ports without acknowledgment. Alias A collection of objects that can be zoned together. An alias is not a zone, and can not have a zone or another alias as a member. Domain ID User defined name that identifies the switch in the fabric. AL_PA Arbitrated Loop Physical Address E_Port Expansion port.
Frame Data unit consisting of a start-of-frame (SOF) delimiter, header, data payload, CRC, and an end-of-frame (EOF) delimiter. FRU Field Replaceable Unit Heartbeat LED A chassis LED that indicates the status of the internal switch processor and the results of the Power-On Self-Test. Initiator The device that initiates a data exchange with a target device. In-Order-Delivery A feature that requires that frames be received in the same order in which they were sent.
SANbox2-8c Fibre Channel Switch Installation Guide Small Form-Factor Pluggable Transceiver A transceiver device, smaller than a Gigabit Interface Converter, that plugs into the Fibre Channel port. SNMP Simple Network Management Protocol Target A storage device that responds to an initiator device. VCCI Voluntary Control Council for Interference Worldwide Name (WWN) A unique 64-bit address assigned to a device by the device manufacturer.
SANbox2-8c Fibre Channel Switch Installation Guide Notes Glossary-4 59042-00 A
Index A Access Control List zone 3-9 account name 3-10, B-61 ACL - See Access Control List Activity LED 2-4, 2-7 Admin authority 3-10, B-3 Admin command B-4 air flow 2-9, A-3 alias add member port B-5 copy B-5 create B-5 delete B-5 delete member port B-6 rename B-6 Alias command B-5 ALPA - See Arbitrated Loop Physical Address altitude A-3 Arbitrated Loop Physical Address 3-1 authority 3-10 B bandwidth aggregate A-2 point-to-point A-2 summary 3-7 blink pattern configuration file system error 5-2 fatal error
SANbox2-8c Fibre Channel Switch Installation Guide environmental conditions 4-2 specifications A-3 error configuration file system 5-2 fatal 5-2 Ethernet connection 4-10, A-2 port 2-7 expansion port 2-5, 4-14 F F_Port 2-5, 4-14 fabric aggregate bandwidth A-2 management 3-10, A-2 management switch 2-7 management workstation 4-1 multiple chassis 3-2 point-to-point bandwidth A-2 ports 2-5 security 3-10 fabric security 4-12 factory default settings B-18 Fallback command B-10 fan 2-9 Fan Fail LED 2-3, 5-6 f
SANbox2-8c Fibre Channel Switch Installation Guide Lip command B-14 log file 5-6, B-30, B-50 Logged-In LED 2-4, 2-6, 5-3 M maintainability A-2 maintenance connection A-2 management workstation 2-7 marking A-4 media type A-2 memory 4-1 mesh topology 3-4 minicom 4-12 multistage topology 3-5 speed A-2, B-33 state B-33 POST - See Power On Self Test power consumption A-3 cords 4-2 requirements 4-1 source loading A-3 supply 2-9 Power On Self Test 4-6, 5-1 principal priority 3-2 principal switch 3-2 private
SANbox2-8c Fibre Channel Switch Installation Guide SFP - See Small Form-Factor Pluggable shock A-3 Show command B-39 Show Config command B-48 Show Log command B-50 Show Perf command B-52 Show Setup command B-53 Shutdown command B-55 Simple Network Management Protocol 2-9 site requirements 4-1 Small Form-Factor Pluggable transceiver 2-5, 4-14 SNMP - See Simple Network Management Protocol SNMP configuration B-18, B-34, B-53 soft zone 3-9 subnet mask 4-13 switch administrative state B-38 agent A-2 configur
SANbox2-8c Fibre Channel Switch Installation Guide create B-65 deactivate B-65 delete B-65 delete member zone B-66 display B-66 display active B-65 display members B-66 display zones B-63 rename B-66 Zoneset command B-65 zoning configuration reset B-18 database 3-8 edit B-67 limits 3-8 list definitions B-67 save edits B-67 Zoning command B-67 59042-00 A Index-5
SANbox2-8c Fibre Channel Switch Installation Guide Notes Index-6 59042-00 A
