user manual
Table Of Contents
- Table of Contents
- Section 1 Introduction
- Section 2 Command Line Interface Usage
- Section 3 User Account Configuration
- Section 4 Network and Fabric Configuration
- Section 5 Switch Configuration
- 5.1 Displaying Switch Information
- 5.2 Managing Switch Services
- 5.3 Managing Switch Configurations
- 5.4 Paging a Switch
- 5.5 Setting the Date and Time
- 5.6 Resetting a Switch
- 5.7 Installing Firmware
- 5.8 Managing Switch Feature Upgrades
- Section 6 Port Configuration
- Section 7 Zoning Configuration
- Section 8 Connection Security Configuration
- Section 9 Device Security Configuration
- Section 10 RADIUS Server Configuration
- Section 11 Event Log Configuration
- Section 12 Simple Network Management Protocol Configuration
- Section 13 Command Reference
- 13.1 Access Authority
- 13.2 Syntax and Keywords
- 13.3 Notes and Examples
- 13.4 Command Listing
- Admin
- Alias
- Config
- Create
- Date
- Exit
- Fcping
- Fctrace
- Feature
- Firmware Install
- Group
- Hardreset
- Help
- History
- Hotreset
- Image
- Lip
- Logout
- Passwd
- Ping
- Ps
- Quit
- Reset
- Security
- Securityset
- Set Alarm
- Set Beacon
- Set Config Port
- Set Config Security
- Set Config Security Portbinding
- Set Config Switch
- Set Config Threshold
- Set Config Zoning
- Set Log
- Set Pagebreak
- Set Port
- Set Setup Radius
- Set Setup Services
- Set Setup SNMP
- Set Setup System
- Set Switch State
- Set Timezone
- Show About
- Show Alarm
- Show Broadcast
- Show Chassis
- Show Config Port
- Show Config Security
- Show Config Security Portbinding
- Show Config Switch
- Show Config Threshold
- Show Config Zoning
- Show Domains
- Show Donor
- Show Fabric
- Show FDMI
- Show Interface
- Show Log
- Show LSDB
- Show Media
- Show Mem
- Show NS
- Show Pagebreak
- Show Perf
- Show Port
- Show Post Log
- Show Setup Mfg
- Show Setup Radius
- Show Setup Services
- Show Setup SNMP
- Show Setup System
- Show Steering
- Show Switch
- Show Timezone
- Show Topology
- Show Users
- Show Version
- Shutdown
- Test Cancel
- Test Port
- Test Status
- Uptime
- User
- Whoami
- Zone
- Zoneset
- Zoning
- Index
7 – Zoning Configuration
Managing Zone Sets
7-14 59183-01 A
S
7.6.3
Rename a Zone Set
Enter the Zoneset Rename command to rename a zone set as shown in the
following example:
SANbox #> admin start
SANbox (admin) #> zoning edit
SANbox (admin-zoning) #> zoneset rename zoneset_old zoneset_new
SANbox (admin-zoning) #>zoning save
7.6.4
Copy a Zone Set
Enter the Zoneset Copy command to copy a zone set and its contents to a new
zone set as shown in the following example:
SANbox #> admin start
SANbox (admin) #> zoning edit
SANbox (admin-zoning) #> zoneset copy zoneset_1 zoneset_2
SANbox (admin-zoning) #>zoning save
7.6.5
Add Zones to a Zone Set
Enter the Zoneset Add command to add a zone to a zone set as shown in the
following example:
SANbox #> admin start
SANbox (admin) #> zoning edit
SANbox (admin-zoning) #> zoneset add zoneset_1 zone_1 zone_2
7.6.6
Remove Zones from a Zone Set
Enter the Zoneset Remove command to remove zones from a zone set as shown
in the following example:
SANbox #> admin start
SANbox (admin) #> zoning edit
SANbox (admin-zoning) #> zoneset remove zoneset_1 zone_1 zone_2
SANbox (admin-zoning) #>zoning save
7.6.7
Activate a Zone Set
Enter the Zoneset Activate command to apply zoning to the fabric as shown in the
following example:
SANbox #> admin start
SANbox (admin) #> zoneset activate zoneset_1