user manual
Table Of Contents
- Table of Contents
- Section 1 Introduction
- Section 2 Command Line Interface Usage
- Section 3 User Account Configuration
- Section 4 Network and Fabric Configuration
- Section 5 Switch Configuration
- 5.1 Displaying Switch Information
- 5.2 Managing Switch Services
- 5.3 Managing Switch Configurations
- 5.4 Paging a Switch
- 5.5 Setting the Date and Time
- 5.6 Resetting a Switch
- 5.7 Installing Firmware
- 5.8 Managing Switch Feature Upgrades
- Section 6 Port Configuration
- Section 7 Zoning Configuration
- Section 8 Connection Security Configuration
- Section 9 Device Security Configuration
- Section 10 RADIUS Server Configuration
- Section 11 Event Log Configuration
- Section 12 Simple Network Management Protocol Configuration
- Section 13 Command Reference
- 13.1 Access Authority
- 13.2 Syntax and Keywords
- 13.3 Notes and Examples
- 13.4 Command Listing
- Admin
- Alias
- Config
- Create
- Date
- Exit
- Fcping
- Fctrace
- Feature
- Firmware Install
- Group
- Hardreset
- Help
- History
- Hotreset
- Image
- Lip
- Logout
- Passwd
- Ping
- Ps
- Quit
- Reset
- Security
- Securityset
- Set Alarm
- Set Beacon
- Set Config Port
- Set Config Security
- Set Config Security Portbinding
- Set Config Switch
- Set Config Threshold
- Set Config Zoning
- Set Log
- Set Pagebreak
- Set Port
- Set Setup Radius
- Set Setup Services
- Set Setup SNMP
- Set Setup System
- Set Switch State
- Set Timezone
- Show About
- Show Alarm
- Show Broadcast
- Show Chassis
- Show Config Port
- Show Config Security
- Show Config Security Portbinding
- Show Config Switch
- Show Config Threshold
- Show Config Zoning
- Show Domains
- Show Donor
- Show Fabric
- Show FDMI
- Show Interface
- Show Log
- Show LSDB
- Show Media
- Show Mem
- Show NS
- Show Pagebreak
- Show Perf
- Show Port
- Show Post Log
- Show Setup Mfg
- Show Setup Radius
- Show Setup Services
- Show Setup SNMP
- Show Setup System
- Show Steering
- Show Switch
- Show Timezone
- Show Topology
- Show Users
- Show Version
- Shutdown
- Test Cancel
- Test Port
- Test Status
- Uptime
- User
- Whoami
- Zone
- Zoneset
- Zoning
- Index
6 – Port Configuration
Displaying Port Information
6-6 59183-01 A
S
6.1.5
Transceiver Information
Enter the Show Media command to display operational information about one or
more transceivers as shown in the following example. Refer to Table 13-25 for a
description of the transceiver information in the Show Media display.
SANbox #> show media 4
Port Number: 4
-------------
MediaType 400-M5-SN-I
MediaVendor FINISAR CORP.
MediaPartNumber FTRJ8524P2BNL
MediaRevision A
MediaSerialNumber P6G22RL
MediaSpeeds 1Gb/s, 2Gb/s, 4Gb/s
Temp Voltage Tx Bias Tx Pwr Rx Pwr
(C) (V) (mA) (mW) (mW)
----------- ----------- ------------ ----------- -----------
Value 37.32 3.33 7.30 0.373 0.000
Status Normal HighWarning Normal Normal LowAlarm
HighAlarm 95.00 3.90 17.00 0.637 1.264
HighWarning 90.00 3.70 14.00 0.637 0.791
LowWarning -20.00 2.90 2.00 0.082 0.028
LowAlarm -25.00 2.70 1.00 0.073 0.019
NOTE: The Show Media command requires the SANdoctor license key. To
purchase a license key, contact your authorized maintenance provider
or authorized reseller.