user manual
Table Of Contents
- Table of Contents
- Section 1 Introduction
- Section 2 Command Line Interface Usage
- Section 3 User Account Configuration
- Section 4 Network and Fabric Configuration
- Section 5 Switch Configuration
- 5.1 Displaying Switch Information
- 5.2 Managing Switch Services
- 5.3 Managing Switch Configurations
- 5.4 Paging a Switch
- 5.5 Setting the Date and Time
- 5.6 Resetting a Switch
- 5.7 Installing Firmware
- 5.8 Managing Switch Feature Upgrades
- Section 6 Port Configuration
- Section 7 Zoning Configuration
- Section 8 Connection Security Configuration
- Section 9 Device Security Configuration
- Section 10 RADIUS Server Configuration
- Section 11 Event Log Configuration
- Section 12 Simple Network Management Protocol Configuration
- Section 13 Command Reference
- 13.1 Access Authority
- 13.2 Syntax and Keywords
- 13.3 Notes and Examples
- 13.4 Command Listing
- Admin
- Alias
- Config
- Create
- Date
- Exit
- Fcping
- Fctrace
- Feature
- Firmware Install
- Group
- Hardreset
- Help
- History
- Hotreset
- Image
- Lip
- Logout
- Passwd
- Ping
- Ps
- Quit
- Reset
- Security
- Securityset
- Set Alarm
- Set Beacon
- Set Config Port
- Set Config Security
- Set Config Security Portbinding
- Set Config Switch
- Set Config Threshold
- Set Config Zoning
- Set Log
- Set Pagebreak
- Set Port
- Set Setup Radius
- Set Setup Services
- Set Setup SNMP
- Set Setup System
- Set Switch State
- Set Timezone
- Show About
- Show Alarm
- Show Broadcast
- Show Chassis
- Show Config Port
- Show Config Security
- Show Config Security Portbinding
- Show Config Switch
- Show Config Threshold
- Show Config Zoning
- Show Domains
- Show Donor
- Show Fabric
- Show FDMI
- Show Interface
- Show Log
- Show LSDB
- Show Media
- Show Mem
- Show NS
- Show Pagebreak
- Show Perf
- Show Port
- Show Post Log
- Show Setup Mfg
- Show Setup Radius
- Show Setup Services
- Show Setup SNMP
- Show Setup System
- Show Steering
- Show Switch
- Show Timezone
- Show Topology
- Show Users
- Show Version
- Shutdown
- Test Cancel
- Test Port
- Test Status
- Uptime
- User
- Whoami
- Zone
- Zoneset
- Zoning
- Index
5 – Switch Configuration
Setting the Date and Time
5-18 59183-01 A
S
Enter the Set Timezone to change the time zone as shown in the following
example:
SANbox (admin) #> set timezone
Africa America
Antarctica Asia
Atlantic Australia
Europe Indian
Pacific UTC
Press ENTER for more options or 'q' to make a selection.
America/Grenada America/Guadeloupe
America/Guatemala America/Guayaquil
America/Guyana America/Halifax
America/Havana America/Hermosillo
America/Indiana America/Indianapolis
.
.
.
America/Monterrey America/Montevideo
America/Montreal America/Montserrat
America/Nassau America/New_York
America/Nipigon America/Nome
America/Noronha America/North_Dakota
America/Panama America/Pangnirtung
Press ENTER for more options or 'q' to make a selection.
q
Enter selection (or 'q' to quit): america/north_dakota
America/North_Dakota/Center
Enter selection (or 'q' to quit): america/north_dakota/center
Enter the Date command to display the date and time as shown in the following
example:
SANbox #> date
Mon Apr 07 07:51:24 200x
Enter the Date command within an Admin session to set the date and time as
shown in the following example:
SANbox #> admin start
SANbox (admin) #> date 013110152025
SANbox (admin) #> date
Fri Jan 31 10:15:03 UTC 2025