user manual
Table Of Contents
- Table of Contents
- Section 1 Introduction
- Section 2 Command Line Interface Usage
- Section 3 User Account Configuration
- Section 4 Network and Fabric Configuration
- Section 5 Switch Configuration
- 5.1 Displaying Switch Information
- 5.2 Managing Switch Services
- 5.3 Managing Switch Configurations
- 5.4 Paging a Switch
- 5.5 Setting the Date and Time
- 5.6 Resetting a Switch
- 5.7 Installing Firmware
- 5.8 Managing Switch Feature Upgrades
- Section 6 Port Configuration
- Section 7 Zoning Configuration
- Section 8 Connection Security Configuration
- Section 9 Device Security Configuration
- Section 10 RADIUS Server Configuration
- Section 11 Event Log Configuration
- Section 12 Simple Network Management Protocol Configuration
- Section 13 Command Reference
- 13.1 Access Authority
- 13.2 Syntax and Keywords
- 13.3 Notes and Examples
- 13.4 Command Listing
- Admin
- Alias
- Config
- Create
- Date
- Exit
- Fcping
- Fctrace
- Feature
- Firmware Install
- Group
- Hardreset
- Help
- History
- Hotreset
- Image
- Lip
- Logout
- Passwd
- Ping
- Ps
- Quit
- Reset
- Security
- Securityset
- Set Alarm
- Set Beacon
- Set Config Port
- Set Config Security
- Set Config Security Portbinding
- Set Config Switch
- Set Config Threshold
- Set Config Zoning
- Set Log
- Set Pagebreak
- Set Port
- Set Setup Radius
- Set Setup Services
- Set Setup SNMP
- Set Setup System
- Set Switch State
- Set Timezone
- Show About
- Show Alarm
- Show Broadcast
- Show Chassis
- Show Config Port
- Show Config Security
- Show Config Security Portbinding
- Show Config Switch
- Show Config Threshold
- Show Config Zoning
- Show Domains
- Show Donor
- Show Fabric
- Show FDMI
- Show Interface
- Show Log
- Show LSDB
- Show Media
- Show Mem
- Show NS
- Show Pagebreak
- Show Perf
- Show Port
- Show Post Log
- Show Setup Mfg
- Show Setup Radius
- Show Setup Services
- Show Setup SNMP
- Show Setup System
- Show Steering
- Show Switch
- Show Timezone
- Show Topology
- Show Users
- Show Version
- Shutdown
- Test Cancel
- Test Port
- Test Status
- Uptime
- User
- Whoami
- Zone
- Zoneset
- Zoning
- Index
13 – Command Reference
Show Perf
13-128 59183-01 A
S
Examples The following is an example of the Show Perf command:
SANbox #> show perf
Port Bytes/s Bytes/s Bytes/s Frames/s Frames/s Frames/s
Number (in) (out) (total) (in) (out) (total)
------ ------- ------- ------- -------- -------- --------
0 7K 136M 136M 245 68K 68K
1 58K 0 58K 1K 0 1K
2 0 0 0 0 0 0
3 0 0 0 0 0 0
4 0 0 0 0 0 0
5 0 0 0 0 0 0
6 0 7K 7K 0 245 245
7 136M 58K 136M 68K 1K 70K
8 7K 136M 136M 245 68K 68K
9 58K 0 58K 1K 0 1K
10 0 0 0 0 0 0
11 0 0 0 0 0 0
12 0 0 0 0 0 0
13 0 0 0 0 0 0
14 0 7K 7K 0 245 245
15 136M 58K 136M 68K 1K 70K
16 47M 23K 47M 23K 726 24K
17 0 0 0 0 0 0
18 23K 47M 47M 726 23K 24K
19 0 0 0 0 0 0
The following is an example of the Show Perf Byte command:
SANbox #> show perf byte
Displaying bytes/sec (total)... (Press any key to stop display)
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
--------------------------------------------------------------------------------
0 0 0 0 0 0 0 0 137M 58K 0 0 0 0 8K 137M
0 0 0 0 0 0 0 0 136M 58K 0 0 0 0 8K 136M
0 0 0 0 0 0 0 0 135M 58K 0 0 0 0 7K 135M
0 0 0 0 0 0 0 0 137M 58K 0 0 0 0 8K 137M
0 0 0 0 0 0 0 0 136M 58K 0 0 0 0 7K 136M
0 0 0 0 0 0 0 0 137M 58K 0 0 0 0 8K 137M
0 0 0 0 0 0 0 0 136M 58K 0 0 0 0 8K 136M
0 0 0 0 0 0 0 0 136M 58K 0 0 0 0 7K 136M
q