user manual
Table Of Contents
- Table of Contents
- Section 1 Introduction
- Section 2 Command Line Interface Usage
- Section 3 User Account Configuration
- Section 4 Network and Fabric Configuration
- Section 5 Switch Configuration
- 5.1 Displaying Switch Information
- 5.2 Managing Switch Services
- 5.3 Managing Switch Configurations
- 5.4 Paging a Switch
- 5.5 Setting the Date and Time
- 5.6 Resetting a Switch
- 5.7 Installing Firmware
- 5.8 Managing Switch Feature Upgrades
- Section 6 Port Configuration
- Section 7 Zoning Configuration
- Section 8 Connection Security Configuration
- Section 9 Device Security Configuration
- Section 10 RADIUS Server Configuration
- Section 11 Event Log Configuration
- Section 12 Simple Network Management Protocol Configuration
- Section 13 Command Reference
- 13.1 Access Authority
- 13.2 Syntax and Keywords
- 13.3 Notes and Examples
- 13.4 Command Listing
- Admin
- Alias
- Config
- Create
- Date
- Exit
- Fcping
- Fctrace
- Feature
- Firmware Install
- Group
- Hardreset
- Help
- History
- Hotreset
- Image
- Lip
- Logout
- Passwd
- Ping
- Ps
- Quit
- Reset
- Security
- Securityset
- Set Alarm
- Set Beacon
- Set Config Port
- Set Config Security
- Set Config Security Portbinding
- Set Config Switch
- Set Config Threshold
- Set Config Zoning
- Set Log
- Set Pagebreak
- Set Port
- Set Setup Radius
- Set Setup Services
- Set Setup SNMP
- Set Setup System
- Set Switch State
- Set Timezone
- Show About
- Show Alarm
- Show Broadcast
- Show Chassis
- Show Config Port
- Show Config Security
- Show Config Security Portbinding
- Show Config Switch
- Show Config Threshold
- Show Config Zoning
- Show Domains
- Show Donor
- Show Fabric
- Show FDMI
- Show Interface
- Show Log
- Show LSDB
- Show Media
- Show Mem
- Show NS
- Show Pagebreak
- Show Perf
- Show Port
- Show Post Log
- Show Setup Mfg
- Show Setup Radius
- Show Setup Services
- Show Setup SNMP
- Show Setup System
- Show Steering
- Show Switch
- Show Timezone
- Show Topology
- Show Users
- Show Version
- Shutdown
- Test Cancel
- Test Port
- Test Status
- Uptime
- User
- Whoami
- Zone
- Zoneset
- Zoning
- Index
13 – Command Reference
Show Media
13-118 59183-01 A
S
Show Media
Displays transceiver operational and diagnostic information for one or more ports.
Authority None
Syntax show media
[port_list]
all
installed
Keywords [port_list]
The port or ports for which to display transceiver information. [port_list] can be a
set of port numbers and ranges delimited by spaces. For example, [0 2 10-15]
specifies ports 0, 2, 10, 11, 12, 13, 14, and 15.
all
Displays transceiver information for all ports.
installed
Displays transceiver information for all ports that have transceivers installed.
Notes Table 13-25 describes the transceiver information in the Show Media display.
NOTE: This command requires the SANdoctor license key. To purchase a
license key, contact your authorized maintenance provider or
authorized reseller.
Table 13-25. Transceiver Information
Information Type Description
MediaType Fibre Channel specification or one of the following:
NotInstalled–transceiver is not installed.
Unknown–transceiver does not have a serial ID.
NotApplicable–transceiver is not needed.
MediaVendor Vendor name
MediaPartNumber Vendor media part number
MediaRevision Vender media revision level
MediaSerialNumber Vendor media serial number
MediaSpeeds Transmission speed capabilities