user manual
Table Of Contents
- Table of Contents
- Section 1 Introduction
- Section 2 Command Line Interface Usage
- Section 3 User Account Configuration
- Section 4 Network and Fabric Configuration
- Section 5 Switch Configuration
- 5.1 Displaying Switch Information
- 5.2 Managing Switch Services
- 5.3 Managing Switch Configurations
- 5.4 Paging a Switch
- 5.5 Setting the Date and Time
- 5.6 Resetting a Switch
- 5.7 Installing Firmware
- 5.8 Managing Switch Feature Upgrades
- Section 6 Port Configuration
- Section 7 Zoning Configuration
- Section 8 Connection Security Configuration
- Section 9 Device Security Configuration
- Section 10 RADIUS Server Configuration
- Section 11 Event Log Configuration
- Section 12 Simple Network Management Protocol Configuration
- Section 13 Command Reference
- 13.1 Access Authority
- 13.2 Syntax and Keywords
- 13.3 Notes and Examples
- 13.4 Command Listing
- Admin
- Alias
- Config
- Create
- Date
- Exit
- Fcping
- Fctrace
- Feature
- Firmware Install
- Group
- Hardreset
- Help
- History
- Hotreset
- Image
- Lip
- Logout
- Passwd
- Ping
- Ps
- Quit
- Reset
- Security
- Securityset
- Set Alarm
- Set Beacon
- Set Config Port
- Set Config Security
- Set Config Security Portbinding
- Set Config Switch
- Set Config Threshold
- Set Config Zoning
- Set Log
- Set Pagebreak
- Set Port
- Set Setup Radius
- Set Setup Services
- Set Setup SNMP
- Set Setup System
- Set Switch State
- Set Timezone
- Show About
- Show Alarm
- Show Broadcast
- Show Chassis
- Show Config Port
- Show Config Security
- Show Config Security Portbinding
- Show Config Switch
- Show Config Threshold
- Show Config Zoning
- Show Domains
- Show Donor
- Show Fabric
- Show FDMI
- Show Interface
- Show Log
- Show LSDB
- Show Media
- Show Mem
- Show NS
- Show Pagebreak
- Show Perf
- Show Port
- Show Post Log
- Show Setup Mfg
- Show Setup Radius
- Show Setup Services
- Show Setup SNMP
- Show Setup System
- Show Steering
- Show Switch
- Show Timezone
- Show Topology
- Show Users
- Show Version
- Shutdown
- Test Cancel
- Test Port
- Test Status
- Uptime
- User
- Whoami
- Zone
- Zoneset
- Zoning
- Index
13 – Command Reference
Set Setup System
59183-01 A 13-93
A
Set Setup System
Configures the network, session, and logging settings on the switch.
Authority Admin session
Syntax set setup system
Prompts you in a line-by-line fashion to change system configuration settings.
Table 13-23 describes the system configuration fields. For each parameter, enter
a new value or press the Enter key to accept the current value shown in brackets.
NOTE: Changing the IP address will terminate all Ethernet management
sessions.
Table 13-23. System Configuration Settings
Entry Description
EthNetworkEnable Enables (True) or disables (False) the Ethernet port. The
default is True.
EthNetworkDiscovery Ethernet boot method: 1 - Static, 2 - Bootp, 3 - DHCP,
4 - RARP. The default is 1 - Static.
EthNetworkAddress Ethernet Internet Protocol (IP) address. The default is
10.0.0.1.
EthNetworkMask Ethernet subnet mask address. The default is 255.0.0.0.
EthGatewayAddress Ethernet IP address gateway. The default is 10.0.0.254
AdminTimeout Amount of time in minutes the switch waits before termi-
nating an idle Admin session. Zero (0) disables the time
out threshold. The default is 30, the maximum is 1440.
InactivityTimeout Amount of time in minutes the switch waits before termi-
nating an idle Telnet command line interface session.
Zero (0) disables the time out threshold. The default is 0,
the maximum is 1440.
LocalLogEnabled Enables (True) or disables (False) the saving of log infor-
mation on the switch. The default is True.
RemoteLogEnabled Enables (True) or disables (False) the recording of the
switch event log on a remote host that supports the sys-
log protocol. The default is False.
RemoteLogHostAddress The IP address of the host that will receive the switch
event log information if remote logging is enabled. The
default is 10.0.0.254.