user manual
Table Of Contents
- Table of Contents
- Section 1 Introduction
- Section 2 Command Line Interface Usage
- Section 3 User Account Configuration
- Section 4 Network and Fabric Configuration
- Section 5 Switch Configuration
- 5.1 Displaying Switch Information
- 5.2 Managing Switch Services
- 5.3 Managing Switch Configurations
- 5.4 Paging a Switch
- 5.5 Setting the Date and Time
- 5.6 Resetting a Switch
- 5.7 Installing Firmware
- 5.8 Managing Switch Feature Upgrades
- Section 6 Port Configuration
- Section 7 Zoning Configuration
- Section 8 Connection Security Configuration
- Section 9 Device Security Configuration
- Section 10 RADIUS Server Configuration
- Section 11 Event Log Configuration
- Section 12 Simple Network Management Protocol Configuration
- Section 13 Command Reference
- 13.1 Access Authority
- 13.2 Syntax and Keywords
- 13.3 Notes and Examples
- 13.4 Command Listing
- Admin
- Alias
- Config
- Create
- Date
- Exit
- Fcping
- Fctrace
- Feature
- Firmware Install
- Group
- Hardreset
- Help
- History
- Hotreset
- Image
- Lip
- Logout
- Passwd
- Ping
- Ps
- Quit
- Reset
- Security
- Securityset
- Set Alarm
- Set Beacon
- Set Config Port
- Set Config Security
- Set Config Security Portbinding
- Set Config Switch
- Set Config Threshold
- Set Config Zoning
- Set Log
- Set Pagebreak
- Set Port
- Set Setup Radius
- Set Setup Services
- Set Setup SNMP
- Set Setup System
- Set Switch State
- Set Timezone
- Show About
- Show Alarm
- Show Broadcast
- Show Chassis
- Show Config Port
- Show Config Security
- Show Config Security Portbinding
- Show Config Switch
- Show Config Threshold
- Show Config Zoning
- Show Domains
- Show Donor
- Show Fabric
- Show FDMI
- Show Interface
- Show Log
- Show LSDB
- Show Media
- Show Mem
- Show NS
- Show Pagebreak
- Show Perf
- Show Port
- Show Post Log
- Show Setup Mfg
- Show Setup Radius
- Show Setup Services
- Show Setup SNMP
- Show Setup System
- Show Steering
- Show Switch
- Show Timezone
- Show Topology
- Show Users
- Show Version
- Shutdown
- Test Cancel
- Test Port
- Test Status
- Uptime
- User
- Whoami
- Zone
- Zoneset
- Zoning
- Index
13 – Command Reference
Hotreset
59183-01 A 13-33
A
Hotreset
Resets the switch for the purpose of activating the pending firmware without
disrupting traffic. This command terminates all management sessions, saves all
configuration information, and clears the event log. After the pending firmware is
activated, the configuration is recovered. This process may take a few minutes. To
save the event log to a file before resetting, enter the Set Log Archive command.
Authority Admin session
Syntax hotreset
Notes You can load and activate version 6.7.x firmware on an operating switch
without disrupting data traffic or having to re-initialize attached devices under
the following conditions:
The current firmware version permits the installation and
non-disruptive activation of 6.7 firmware. Refer to the 6.7 Firmware
Release Notes for previous compatible firmware versions.
No changes are being made to switches in the fabric including
installing firmware, powering up, powering down, disconnecting or
connecting ISLs, and switch configuration changes.
No port on the switch is in the diagnostic state.
No zoning changes are being made on the switch.
No changes are being made to attached devices including powering
up, powering down, disconnecting, connecting, and HBA configuration
changes.
Ports that are stable when the non-disruptive activation begins, then change
states, will be reset. When the non-disruptive activation is complete,
Enterprise Fabric Suite 2007 sessions reconnect automatically. However,
CLI and SSH sessions must be restarted manually.
This command clears the event log and all counters.