user manual
Table Of Contents
- Table of Contents
- Section 1 Introduction
- Section 2 Command Line Interface Usage
- Section 3 User Account Configuration
- Section 4 Network and Fabric Configuration
- Section 5 Switch Configuration
- 5.1 Displaying Switch Information
- 5.2 Managing Switch Services
- 5.3 Managing Switch Configurations
- 5.4 Paging a Switch
- 5.5 Setting the Date and Time
- 5.6 Resetting a Switch
- 5.7 Installing Firmware
- 5.8 Managing Switch Feature Upgrades
- Section 6 Port Configuration
- Section 7 Zoning Configuration
- Section 8 Connection Security Configuration
- Section 9 Device Security Configuration
- Section 10 RADIUS Server Configuration
- Section 11 Event Log Configuration
- Section 12 Simple Network Management Protocol Configuration
- Section 13 Command Reference
- 13.1 Access Authority
- 13.2 Syntax and Keywords
- 13.3 Notes and Examples
- 13.4 Command Listing
- Admin
- Alias
- Config
- Create
- Date
- Exit
- Fcping
- Fctrace
- Feature
- Firmware Install
- Group
- Hardreset
- Help
- History
- Hotreset
- Image
- Lip
- Logout
- Passwd
- Ping
- Ps
- Quit
- Reset
- Security
- Securityset
- Set Alarm
- Set Beacon
- Set Config Port
- Set Config Security
- Set Config Security Portbinding
- Set Config Switch
- Set Config Threshold
- Set Config Zoning
- Set Log
- Set Pagebreak
- Set Port
- Set Setup Radius
- Set Setup Services
- Set Setup SNMP
- Set Setup System
- Set Switch State
- Set Timezone
- Show About
- Show Alarm
- Show Broadcast
- Show Chassis
- Show Config Port
- Show Config Security
- Show Config Security Portbinding
- Show Config Switch
- Show Config Threshold
- Show Config Zoning
- Show Domains
- Show Donor
- Show Fabric
- Show FDMI
- Show Interface
- Show Log
- Show LSDB
- Show Media
- Show Mem
- Show NS
- Show Pagebreak
- Show Perf
- Show Port
- Show Post Log
- Show Setup Mfg
- Show Setup Radius
- Show Setup Services
- Show Setup SNMP
- Show Setup System
- Show Steering
- Show Switch
- Show Timezone
- Show Topology
- Show Users
- Show Version
- Shutdown
- Test Cancel
- Test Port
- Test Status
- Uptime
- User
- Whoami
- Zone
- Zoneset
- Zoning
- Index
13 – Command Reference
Config
13-8 59183-01 A
S
edit [config_name]
Opens an edit session for the configuration given by [config_name]. If you omit
[config_name], the currently active configuration is used.
list
Displays a list of all available configurations on the switch. This keyword does not
require an Admin session.
restore
Restores configuration settings to an out-of-band switch from a backup file named
configdata, which must be first uploaded on the switch using FTP. You create the
backup file using the Config Backup command. Use FTP to load the backup file
on a switch, then enter the Config Restore command. After the restore is
complete, the switch automatically resets. Refer to “Back Up and Restore a
Switch Configuration” on page 5-14.
save [config_name]
Saves changes made during a configuration edit session in the configuration
given by [config_name]. If you omit [config_name], the value for [config_name]
you chose for the most recent Config Edit command is used. [config_name] can
be up to 31 characters excluding #, semicolon (;), and comma (,). The switch
supports up to 10 configurations including the default configuration.
Notes Changes you make to an active or inactive configuration can be saved, but will not
take effect until you activate that configuration.
NOTE: If the restore process changes the IP address, use the
Set Setup System command to return the IP configuration to the
values you want. If the IP address is unknown, you must place the
switch in maintenance mode and reset the network configuration to
restore the default IP address 10.0.0.1. Refer to the installation
guide for information about using maintenance mode.
Configuration archive files created with the Enterprise Fabric Suite
2007 Archive function are not compatible with the Config Restore
command.
The configdata backup file does not include the security group
primary or secondary secrets, and therefore are not restored. You
must edit the security database and reconfigure the secrets. If they
are not, the switch will isolate from the fabric.