Owner's Manual

ManualsBrandsQ-Logic ManualsAudio accessories & installationInstall 6-1/2" components in your 2003-up Hummer H2 (Wheat)

QL-K1015

2002-up Hummer H2

Note: Always check the fit of the Q-Forms panel in the vehicle BEFORE any cutting or modifications are done!

Continued on other side:

FACTORY KICKPANEL REMOVEL: Driver & Passenger Sides

Remove the factory sill plate by gently prying up on the inside edge. Remove

the factory kick panel by grasping the back and bottom areas of the kickpanel

and gently pulling toward the rear of the vehicle releasing the spring clips

attaching the panel.

Q-FORMS KICKPANEL INSTALLATION:

Driver's Side:

Lay the Q-Forms kickpanel in the approximate location and connect the speaker

wiring. Pull up on the hood release and slide through to opening in the

kickpanel. Install the Q-Forms kickpanel into the permantant postion previously

held by the factory kickpanel. Be sure that the front edge of the kickpanel fits

and tightly and evenly against the rubber door seal. Reinstall the factory sill

plate making sure that the front clip snaps into the Q-Forms kickpanel. While

pushing in and down on the kickpanel, attach the kickpanel using the supplied 1/

2" sheet metal screw through the predrilled hole located in the hood release

area of the kickpanel and into the sheet metal of the vehicle. Lay the polyfill in

the opening for the midrange driver and install the driver as per manufacture's

instruction. Be sure to center the driver in the opening to allow clearence for the

supplied grill.

Supplied Hardware:

1 - 1/2" Sheet Metal Screw

1 - 1" Nylon Spacer

1 - 1 1/2" Sheet Metal Screw

2 - Polyfill Batting

1 - Foam Tape Roll

40" - Rubber U-channel

Passenger's Side:

Lay the Q-Forms kickpanel in the approximate location and connect the speaker

wiring. Install the Q-Forms kickpanel into the permantant postion previously

held by the factory kickpanel. Be sure that the front edge of the kickpanel fits

and tightly and evenly against the rubber door seal. Reinstall the factory sill

plate making sure that the front clip snaps into the Q-Forms kickpanel. While

Continued on other side:

Driver Side Before

Driver Side After

Summary of content (4 pages)

PAGE 1
QL-K1015 2002-up Hummer H2 FACTORY KICKPANEL REMOVEL: Driver & Passenger Sides Remove the factory sill plate by gently prying up on the inside edge. Remove the factory kick panel by grasping the back and bottom areas of the kickpanel and gently pulling toward the rear of the vehicle releasing the spring clips attaching the panel.
PAGE 2
Continued from other side: pushing in and down on the kickpanel, attach the kickpanel using the supplied 1 1/2" sheet metal screw through the predrilled hole located in the kickpanel, through the 1" nylon spacer and into the sheet metal of the vehicle. NOTE: The installation of the screw and spacer may be made easier if a small peice of tape or thin cardboard is placed over the screw once the spacer has been placed over the screw.
PAGE 3
Q-Forms " C - series " Kickpanels for 6.5" Woofers Note: Always check the fit of the Q-Forms panel in the vehicle BEFORE any cutting or modifications are done! 6.5" Woofer Mounting Instructions Please use the model specific instructions provided for the removal of the factory panels and the Q-Forms mounting instructions. These instructions provide information on properly locating the woofer in the Q-Forms kickpanel.
PAGE 4
Continued from other side: Mark Center location using ruler: This will position any area of the grill that hangs over to the back bottom edge of the woofer surface where it will not be visible when installed. With the grill on the mounting surface, mark the screw locations for the woofer. Remove the grill and align the screw locations with the the mounting template to mark to cutout location. Use a ruler and pencil to mark the center point of the cutout by lining up the mounting holes opposite one another.