PYSER-SGI LIMITED PNP-MC Pocket Scope Operator’s Manual YSER-SGI LIMITED Fircroft Way, Edenbridge, Kent United Kingdom, TN8 6HA Telephone: +44 (0) 1732 864111 Facsimile: +44 (0) 1732 865544 Email: sales@pyser-sgi.com www.pyser-sgi.
Chapter 5. Accessorie Mounting 5.3 PNP-MC with head mount / helmet mount fitting guide 1. 2. WARNING 3. LIMITED WARRANTY This product contains an image intensifier tube. The manufacturer of this POCKET SCOPE, has provided a limited warranty to the original purchaser. It was attached to the manufacturer’s terms and conditions of sale. Permanent damage to the tube may result if the product is used in normal room illumination or bright ambient light.
Chapter 5. Accessorie Mounting 5.2 PNP-MC with switching mount 1. 2. 3. 4. Fully unscrew thumb knob C to the end stop Remove the slider block assembly, rotate its orientation accordingly Re attach and tighten thumbscrew C TIP to get maximum tightness, tighten thumbscrew C whilst monocular is at its maximum pitch travel (UP for R/H & DOWN for L/H) then complete tightening whilst turning knob C and simultaneously rotating the monocular into the desired pitch setting.
Chapter 1. Description Chapter Chapter 5. Accessorie Mounting 1 DESCRIPTION 1.1 System description PNP-MC is a powerful, multi-purpose, lightweight, pocket-sized monocular night scope utilising C-mount CCTV lenses for extra flexibility. The pocket scope is designed to be used either as a stand-alone night vision device or in combination with a wide variety of standard video, still-photo or CCTV equipment. insufficient - especially effective inside buildings etc.
Chapter 4. Accessories Chapter 1. Discription 1.2 PNP-MC Specifications Dimensions Optical Camcorder/Camera Adaptor Anti-Mist for eyepiece NSN 5855-99-341-1382 Part No: 560-007-010 30mm 30.5mm 35mm 49mm 52mm 58mm 72mm Part Part Part Part Part Part Part No: No: No: No: No: No: No: 589-840-300 589-840-305 589-840-035 589-840-042 589-840-041 589-840-058A 589-840-072 Others available on request 150mw Illuminator, IR LED wide, mid and narrow FOV, 805nm.
Chapter 1. Description Chapter 4. Accessories 1.3 PNP-MC Standard equipment and accessories Fig. No. 1 - PNP-MC standard kit 3 No. Equipment Qty (1) PNP-MC pocket scope 1 (2) Eye guard 1 (3) Carrying pouch 1 (4) 1.5V “AA” size battery 1 (5) Operator’s manual 1 TABLE NO. 2 PNP-MC Optional accessories Equipment 1 4 2 4 5. The PNP-MC can be removed, if necessary, from the mount and the mount left on the weapon in it’s correct position for next use. TABLE NO.
Chapter 4. Accessories Chapter 1. Description 1.4.1 Objective lens 1.4 PNP-MC Main parts Fig. No. 2 PNP-MC Parts description Standard objective lens in a 25mm F1.4 C-mount lens. (Any C-mount lens can be used). 6 5 Head Harness for left and right eye use and accepts binocular bridge NSN 6650-99-407-0566 Part No: 550-006/AM 16 For dual monocular mounting please see chapter 5 for fitting instructions.
Chapter 1. Description 1.4.4 I.R. LED Illuminator The PNP-MC is equipped with a built-in I.R. LED-type illuminator which provides additional, close-range covert illumination when ambient light is insufficient. The illuminator is activated using the operating switch. 1.4.5 Operating switch Operation of the scope is controlled by a three-position rotary switch: OFF - All power off. ON I.R - The scope is on enabling night vision. - The scope is on and the built-in I.R.
Chapter 3. Troubleshooting Chapter 2. Operating Instructions Table No. 4 General troubleshooting 2.1 Battery installation Chapter 2 1) No Symptom Cause Probable Actions Corrective 1 No visible image a. Objective lens cap has not been removed. b. Battery cover loose. c. Incorrect Battery polarity. d. Weak Battery. a. Remove cap. e. Iris closed 2 3 Persistent Image Flickers. Poor image quality a. Faulty intensifier tube. a. Dirty or fogged objective lens. b. Eyepiece out of focus 14 b.
Chapter 2. Operating Instructions Chapter 3. Troubleshooting 2.7 PNP-MC Lens options Fig. No. 3 Battery installation 1) PNP-MC is designed to accept any C-mount lens. 2) PNP-MC can accept photographic lenses from most manufacturers by using a camera lens to C-mount adaptor. See chapter 4 Accessories. 3) “Off-On-I.R.” switch 2.4 PNP-MC Operation with DSLR/SLR cameras (interchangeable lenses) 2.4.1 Installation 1) 2.3 PNP-MC Applications 2) Fig. No.
Chapter 2. Operating Instructions 2.6 PNP-MC Operation with CCTV cameras Chapter 2. Operating Instructions Fig. No. 8 PNP-MC Installation on CCTV camera 5) 2.6.1 Installation 1) 2) Mount the CCTV relay lens to the PNP-MC eyepiece (after folding back the eye guard). Mount PNP-MC with relay lens to the CCTV camera. CCTV CAMERA 2) 3) 4) 12 Direct the system to the required scenery. Turn PNP-MC and CCTV camera on. Adjust eyepiece diopter until sharpest picture is obtained in the monitor.
Chapter 2. Operating Instructions Chapter 2. Operating Instructions 2.4.3 PNP-MC / camera using original camera & lens 1 3 4 2 2) DSLR Optical Module DSLR Lens DSLR Lens mount 1) Remove original lens from camera (5).and set it to “Manual”. 2) Fit appropriate optical module (4) directly to camera then after folding back rubber eyecup attach module to PNP-MC (3). 3) Attach camera lens to C-mount adaptor (2) to PNP-MC (3).
