User's Manual
top front
back
usb-c
port
charging
indicator
Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
FCC ID: 2AU7D-WPC20001-01 Model: QIC-31 Input: DC5V/2A 9V/2A 12V/1.5A Output: 10W Max Made in China
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause
harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired
operation. Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Target Corp. Mpls. MN, 55403 Phone: 612-304-6073
• Remove credit cards and other cards with magnetic strips to prevent damage to the cards
• Keep the charger away from heat and direct sunlight
• Do not modify or repair this device
• Do not use in high temperatures or extreme weather
• Do not use chemical detergents to clean your device, use a soft dry cloth
• Immediately unplug it from its power source if it gets wet
• Remove the protective lm on the Quick Charge 3.0 wall plug before using
safety
• Double check that the USB-C cable and quick charger 3.0 wall plug are plugged in
• Certain phone cases may interfere with wireless charging. Remove the phone case
for best results
• Double check the placement of the device on the wireless charger. For best results,
the center of the device should be on the center of the wireless charger
• Wireless charging is compatible with iPhone 8 and newer as well as other QI-enabled
devices. Please consult your devices user manual if you are unsure if your device
is compatible
troubleshooting
Can’t get it to charge? Just have a question?
call us at: 877-698-4883 or: 877-MyTgtTech
e-mail us at: TargetTechSupport.com
need some help?
• Alignment matters - centering the device on the charging surface ensures the
fastest and most ecient charge
• Thick phone cases as well as some materials can interfere with the ability to charge
• This is a high speed wireless charger. Make the most of the charger by using the
USB-C cable and quick charger 3.0 wall plug that were packaged with it. Using a
dierent power source may charge your device at a slower speed
quick tips
• Wireless charger
• USB-C charging cable
• Quick Charge 3.0 wall plug
• Solid Red - Charging your device
Solid White - Fully charged
Flashing Red - Foreign object detection, pieces of metal or other materials may cause
overheating and damage your charger or phone. Remove them immediately
indicators
included
• Place the charger on a sturdy at surface
• Connect the quick charger 3.0 wall plug to the wall outlet using the USB-C cable
• If you need to use a dierent power source make sure it is a USB power supply of
DC 9V 2A minimum warning: please use UL compliant power supply
• Place your QI-enabled device onto the wireless charger and align the device with
the center of the charging surface or the device will not charge
• Remove credit cards or any card with a magnetic strip to prevent damage
to the cards before charging
• Charge time will vary by device
charging