User Manual

SFG10
Aluminized Steel header/cross-member back exhaust system for
1960-1964 Ford Galaxie
SFG10: 2-1/2” w/ x-pipe
Thanks again for purchasing your new Pypes Performance Exhaust system.
Please be sure to conrm all the components in the kit were received in your
shipment before beginning installation. These kits will include (2) down-
pipes, (1) X-pipe kit, (2) Mufers (if purchased), (2) tailpipes (2 pieces per
side), (2) mufer hangers, (2) tailpipe hangers, (14) clamps, and (1) bonus
pack. If you purchased a kit including mufers you will see the following no-
tation after the system number: (S) Street Pro, (R) Race Pro, and (V) Viola-
tor. If you nd any component missing, please contact our ofce at 800-421-
3890 for replacement. Installation of this kit will require some simple hand
tools; box wrenches, deep sockets w/ ratchet, extension, a saws-all and
some penetrating lubricant. For a quicker and tighter installation, air tools
are recommended. Fully welding the system is always recommended when
possible.
Technical assistance is available both online at www.pypesexhaust.com or
800-421-3890. Also, our online Installation Gallery is a great assistant dur-
ing your installation, visit www.pypesexhaust.com/pictures.html
Pypes Performance Exhaust
2880 Bergey Road Unit O Hateld, PA 19440
800-421-3890 (voice) 215-712-9968 (fax)
www.pypesexhaust.com
(A) Downpipes
(B) X-pipe Front Legs
(C) X-pipe Assembly
(D) Mufers
(E) Tailpipes
(over the axle)
(F) Tailpipes
(To the Bumper)
(A)
(C)
(D)
(B)
(B)
(E)
(F)
(F)
1. Begin by placing the vehicle on a lift or four jack stands at maximum height to
aid in an easier installation. To help ease the installation, pre-t all the components into a
complete system on your garage oor, using the diagram provided.
2. Remove the existing exhaust system from the exhaust manifolds back.
3. Now it’s time to install your new components. Begin by test installing your new
tailpipes. Since this system uses universal style hangers, you will need to determine the
approximate location to mount them. The tail pipe hangers will mount to the outside of
the frame rails just behind the rear tires. The mufer hangers will get mounted to the rear
seat pans just in front of the rear. If you so choose, custom hangers may be fabricated,
let your creativity shine…
4. Now, install the mufers. The inlet should be closest to the drive shaft and the
outlet should be towards the rockers of the car. The clamp attached to the hanger at the
backside of the mufer will be the only connection clamp used.
5. Next, install the x-pipe. This is where trimming of the tubing may be required
for the optimum t. Install the xed “X” rear legs into the mufers rst. You are aiming
to have the center “X” approx 8-12 inches behind the tail shaft of your transmission and
centered under the driveshaft. Also, the center plate on the “X” has an arrow stamp which
must point forward. Trim the rear legs as needed to put your “X” and mufers in the
proper location. Quick tip: If the rear suspension is unloaded, you can push the center
“X” up until it just about touches the drive shaft as it will never hit once the suspension
is loaded. Slide the front legs into the x-pipe. They should end somewhere close to the
humps in your transmission cross-member. On some applications, the front “X” legs may
not be centered in the humps but line up to your headers or down-pipes. This is ne as
the system will not hang too low. Be extra careful when measuring and cutting. A helpful
tip: Line up the front legs under the center “X” to mark your cut lines making sure to line
them up with you headers or down pipes.
6. Continue by connecting the front legs of the x-pipe to the downpipes. No trim
-
ming should be required.
7. Finish the system by making all your nal adjustments to position the downpipes,
X-pipe, mufers and tailpipes. Now tighten all the clamps (Warning: tightened clamps will
leave marks in the tubing, making removal or adjustments extremely difcult) or for the
best t weld all the slip joints. The system can be welded with your standard mig welder,
and is highly recommended when possible.
Nowit’stimetoreupthatmusclecarandenjoyyour
newPypesPerformanceExhaust.
(A)
(D)
(E)
Becauseofthelimitednatureofthissystem,contactPypesfor
installationdetailsbeforeinstallingthissystem.Alsoseethetest
carpicturesonthePypeswebsiteintheinstallationgallery’