User Manual

5
6
“SE7/25”then press buttons to choose the desired “+”“-”
Sensitivity level (range from 0-255). After choosing of the level, press
“RESET”button to confirm.
<Double Detection function <available for the models with UV
detection or the model with both UV and MG/MT detection>.
---used to check a double-note
--By default, serving as a supplementary function, the detection can
be activated when the unit is powered up.
--If the machine detects a double-note when counting, it will stop and
emit beeping sound, while the batch display will show the message
“d3”(alerting the user the of the presence of a double-note). The
double-note will always be the last one on the stacker. Remove the
dubious bill, press“RESET”button to continue.
<Half-note Detection<available for the models with UV detection or
the model with both UV and MG/MT detection>.
---used to check half-note.
--By default, serving as a supplementary function, the half-note
detection can be activated when the unit is powered up.
--If the machine detects a half-note when counting, it will stop and
emit beeping sound, while the batch display will show the message
“d5”alerting the user the presence of a half-note bill). The dubious
bill will always be the last one on the stacker. Remove the dubious
bill, press“RESET”button to continue<the counting display will
clear>.
1. It is highly recommended to contact the authorized service center
or local dealer before you do the above adjustments.
2. Improper adjustments may cause improper working condition or
false detection results.
CAUTION:
7.Fake money alarm
Fake money or questionable money
When fake money pass the machine, the
counting will stop and alarm. The function
display will show the error code. The last
note on the stacker normally is the fake
money. The machine counting quantity
number is not included in this note. remove
the fake money. Press“RESET”button,
the machine will start counting again.
8.Error code and solution
The batch display may show some error code when counting,
which means there are some problems with the machine.
Refer to the following diagram to find way to solve it.
Remove the suspicious bill on the
stacker, press “RESET”to
continue;
Lower the UV sensitivity.
Suspicious bill detected by
UV system;
Problem in the UV system.
Message
Error
Solution
Suspicious bill detected by
MG/MT system; Problem in
the MG/MT system.
Remove the suspicious bill on the
stacker,press “RESET”to
continue;
Lower the MG/MT sensitivity.
Double-note detected by
IR system;
Problem in the IR system.
Remove the suspicious bill on the
stacker, press “RESET” to
continue;
Lower the IR sensitivity.
Note of size problem
detected by size detection
system; Problem in the size
detection system.
Remove the suspicious bill on the
stacker, press “RESET” to
continue;
Lower the size checking sensitivity.
Half-note detected by
half-note detection system;
Problem in the half-note
detection system.
Remove the suspicious bill on the
stacker,
press “RESET”to continue.
Message
Error
Solution
Generally speaking, most of the above-mentioned problems
may be caused by dust or dirt inside of the machine. So
keeping the machine clean is highly recommended .
< NOTE >
Problem with the
speed sensor
Clean the sensor or replace it
Problem with the
right counting sensor
Clean the sensor or replace it
Problem with the left
counting sensor.
Clean the sensor or replace it.
E01
Problem with the
auto start sensor
9.Hopper adjustment
--When improper feeding of bills occur, adjust the feeding thickness
setting in the hopper by turning the adjustor screw located in the back
of the machine to ensure proper feeding.
Suitable for both new,old,dirty,tattered polymer bills and paper bills
Fully A u t o m a t i c
oney
ounter
m c
Fully uA t o m a t i c
oney
ounter
m c
Suitable for both new,old,dirty,tattered polymer bills and paper bills
Fully A u t o m a t i c
oney
ounter
m c
Fully
uA t o m a t i c
oney
ounter
m c
3
Slope-note detected by slope-
note detection system;
Problem in the slope-note
detection system
Remove the bill from the stacker.
Press “RESET” to continue.
Chain-note detected by chain-
note detection system;
Problem in the chain-note
detection system
Remove the bill from the stacker.
Press “RESET” to continue.
Problem with the
UV sensor
Problem with the
preset sensor
Clean the sensor or replace it
Clean the sensor or replace it
Clean the sensor or replace it
E02
E03
E04
E05
E10