User Manual

3
4
6.Counterfeit Detection
Instead.
-Bills should be correctly placed as indicated in the following steps:
Place the bills between the counting guides as shown in the figure 1,
then push the bills backward to make them lay on the top of the hopper
plate, in the correct counting position as shown in the figure 2.
< NOTE >
added bills will be shown on the counting screen. Press the“ADD”
button to close the function and clear the counting display.
3>Batch Function
--The preset batch function can be performed by pressing the“BATCH”
button (the BATCH indicator will appear). By default, when pressing
the“BATCH”button, the batch function is turn on. The batch number
can be set in amounts between 1and 999 by pressing No.“+”&“-”
button. To clear this function, press the “BATCH”button until the
indicator is off.
--Under the batch counting mode, once the hopper is loaded, the
machine will start counting and stop when the counted quantity
reaches the preset batch one.
--To repeat the batch counting operation under the same preset batch
quantity, just remove the counted bill from the stacker. The unit will
batch the next group of bills under the same settings.
--If you wish to keep batching without removing the preset number,
press the“RESET”button.
--If the counted number does not equal with the preset batch number,
the counter display will show the quantity with blinking number.
--When counting with MG and/or UV detection on, the machine will
stop automatically when detecting counterfeit currency. This function
can be resumed by removing the dubious bill from the stacker and
pressing“RESET”button.
2>Addition Function
Addition function can be performed by pressing the“ADD” button
(the ADD indicator will appear). In this case, removing the counted
bills from the stack will not clear the quantity counted and shown on
the counting display. The next bills placed in the hopper will be
counted and added to the preceding quantity. The total amount of
<UV(Ultraviolet) detection function <available for the model with UV
detection or the model with both UV and MG/MT detections>
---used to check all kinds of banknotes which contains UV features.
--The UV function is automatically turned on by default when the
machine is powered up. It can also be selected or deselected by
pressing the“CF”button located in the function console.
--If the machine detects a counterfeit note when counting, it will stop
and emit beeping sound, while the batch display will show the
message“d1”and the UV indicator will blink (alerting the user of the
presence of a dubious bill). The dubious bill will always be the last
one on the stacker. Remove the dubious bill, press“RESET”button
to continue.
--The sensitivity of UV detection can be adjusted. Hold“BATCH”
button for 3 seconds, the batch display will show the current
sensitivity level“SE4/120”,then keep press“+”“-”button to
choose the desired sensitivity level (range from 0-200). After choosing
the level, press“RESET” button to confirm/save. Do not change
other unmentioned settings, changing other setting may cause
improper working condition.
--The smaller number means the higher sensitivity you set and“0”
means deactivate this detection function.
<MG (Magnetic)/MT(Magnetic thread) detection function <available
for the the models with both UV and MG/MT detections>
---used to check all kinds of banknotes which contains the mentioned
features.
--The MG/MT function is automatically turned on by default when the
machine is powered up. It can also be selected or deselected by
pressing the “CF”button located in the function console.
--If the machine detects a counterfeit note when counting, it will stop
and emit beeping sound, while the batch display will show the
message“d2” and the MG/MT indicator will blink (alerting the user
the presence of a dubious bill). The dubious bill will always be the last
one on the stacker. Remove the dubious bill, press“RESET”button
to continue.
--The sensitivity of MG detection can be adjusted. Hold “BATCH” button
for 3 seconds until the batch display will show the current sensitivity
level“SE5/5,”press“+”“-”button to choose the desired
sensitivity level (range from 0-50). After choosing the level, press“
RESET”button to confirm save. Do not change other unmentioned
settings, changing other setting may cause improper working
condition.
--The bigger number means the higher sensitivity you set and“0”
means deactivate this detection function.
--The UV and MG/MT detection can be used at the same time while
counting to multiply the chances of detecting a counterfeit bill. By
default, the UV and MG/MT detection functions are automatically turn
on when the unit is powered up. Those functions can also be selected
or deselected by pressing “CF”buttons.
<IR (Infrared) Detection Function <available for the models with UV
detection or the model with both UV and MG/MT detection>
---used to check all kinds of banknotes which with thichness problem.
--By default, serving as a supplementary function, the IR detection
can be activated when the unit is powered up.
--The sensitivity of IR detection can be adjusted. Hold “BATCH” button
for 3 seconds, the batch display will show the current sensitivity level
Note:hold”BATCH"button for 3 seconds, " SE5/ " is used to adjust " MG1"
sensitivity level, " SE6/ " is used to adjust “MG2" sensitivity level.
Figure 1. Put the bills by this direction Figure 2. Push the bills backward.
The counting mode can be changed between Automatic and
Manual. Press the“AUTO”button, if the batch display shows
“AUTO”the machine is in automatic counting mode; If without
the“AUTO”shown in the display, the machine is in manual
counting mode, under this manual mode, press the“RESET”
button after placing the bills to start counting.
Suitable for both new,old,dirty,tattered polymer bills and paper bills
Fully A u t o m a t i c
oney
ounter
m c
Fully
uA t o m a t i c
oney
ounter
m c
Suitable for both new,old,dirty,tattered polymer bills and paper bills
Fully A u t o m a t i c
oney
ounter
m c
Fully
uA t o m a t i c
oney
ounter
m c