PUCRC105 User Manual
CONTENTS 1. SAFETY INSTRUCTION 2. COMPONENTS OF CLEANER 2.1 PARTS NAME 2.2 TECHNICAL PARAMETER 3. OPERATION INSTRUCTION 1 2-4 2-4 4 5-8 3.1 QUICK USER GUIDE 5 3.2 CLEANING/STOP/SLEEP 6 3.3 CLEANING MODES SELECTION 3.4 PRE-SET TIMER 4. MAINTENANCE 6-7 8 9-11 4.1 CLEANING SIDE BRUSH 9 4.2 CLEANING THE DUST BOX AND FILTER 9 4.3 CLEANING THE INFRARED RECEIVER AND CHARGING CONNETOR 10 4.4 ASSEMBLY THE MOPPING PAD 11 5. FAILURE CHECKING 12 6.
1. SAFETY INSTRUCTION Please read the following instruction carefully before using. ● Read the instruction and follow the step on operating the unit. ● Keep this instruction manual for future reference. ● Send this instruction manual if you need third party transfer. ● Do not operate the unit with instruction not mentioned in this manual. *Reminders 1. Do not disassemble by yourself. Only authorized technician can do repair and replacement. 2.
2. COMPONENTS OF CLEANER 2.
2. COMPONENTS OF CLEANER Control Panel Indicator light： 1.Cleaning Mode: Blue Flash Light. 2.Error: Red Flash Light. 3.Charging: Red Flash Light. 4.
2. COMPONENTS OF CLEANER Remote Control 1. On/off switch (cancel key) 2. Mode (Normal/low speed) POWERFUL 3. Turn left button 4. Forward button VOICE FULL-GO 5. Turn right button 6. Backward button AUTO SPOT CHARGE MOP CLOCK TIMER 7. Full-Go, Auto cleaning after fully charged Open/Close voice. 8.Spot cleaning mode 9.Auto cleaning mode 10. Mopping mode 11. Auto recharge button 12. Timer setting 13. Clock setting (current time setting) 2.
3. OPERATION INSTRUCTION 3.1 Quick User Guide 1.Charging station position information Please make sure the adaptor has been connected to the charging station. 1M 1M 2M *Reminders Install the charging station on the flat ground firmly and against the vertical wall (fixed on the wall with the charging station sticker). Ensure no obstacle or hollow areas 3m away from the charging station in front and 1.5m on right and left. 2. Two Charging Methods 1.
3. OPERATION INSTRUCTION 3.2 Cleaning/Stop/Sleep 1.Cleaning A. Turn on power switch. B. Press“ ”on unit or press “AUTO“on remote controller to start work. 2. Stop Stop will switch the cleaning mode to stand-by mode, press related button on remote controller or " " to stop, after that can be re-operated on unit. 3. Sleep Please press " " button on remote controller when unit under stand-by mode, then unit will go on sleep mode.
3. OPERATION INSTRUCTION 2.Spot Mode Press the spot cleaning button, it will clean the area within 1m2 and clean by spiral mode. It will automatic operate in around 2-3 minutes. 3. Mopping Mode Press " " button, it will switch to mopping mode, and under this mode the vacuum cleaning mode will stop working. (No suction power and fabric brush stop running). Mopping routes as following: 4.
3. OPERATION INSTRUCTION 3.4 Pre-set timer Set the timer under stand-by mode(stop any working mode), and set the current time (clock) before using the timer function. Set the current time (Clock) 1.Press the “ ” button on remote control, the clock symbol display on screen. 2.Press“ ” “ ”button to select the hour or minute. 3.Press“ ” “ ”button to set the hour or minute. 4.After setting press the Clock button to confirm setting, clock symbol will disappear. r. 5.
4. MAINTENANCE 4.1 Cleaning Side Brush Check the side brushes regularly, and clean them, please replacement it when side brushes are damaged *Reminders Please use the screw driver to take out the brush, then clean the side brush or replacement it. 4.2 Cleaning the dust box and filter Please clean the dustbin box on time after working, cleaning step as following operation figure. *Reminders Take out the dustbin box and check, if needed, then cleaning it.
4. MAINTENANCE 4.3 Cleaning the Infrared Receiver and Charging Connector Please use the dry soft cloth to clean the charging electrode and sensor in front of the unit. *Reminders Please clean the charging electrode on time to avoiding charging issue.
4. MAINTENANCE 4.4 Assembly the Mopping Pad 1. Please stickup the mop cloth on to mop pad, refer following figure. 2.
Failure Code Failure Cause How to solve E04 Left wheel has been stucked E05 Right wheel has been stucked Please clean the right wheel. E06 Detected the cliff The ground is not flat, please move the robot to a new place then start again. E07 Side brushes has been stucked Please clean the side brush. E08 Abnormal speed Replace or repair the speed sensor. E09 Detected the collision The collision sensors stucked, please clean it accordingly.
6. ACCESSORIES LIST Description No. Q'ty 1 Robot cleaner(including Li-ion battery) 1 2 Charging station 1 3 Remote controller 1 4 Adaptor 1 5 Clean brush 1 6 HEPA filter（1pc packed in robot cleaner） 2 7 Side brushes 2 8 Mop pad 1 9 Mopping cloth 2 10 Instruction manual 1 11 Warranty card 1 *Reminders We will improve the product continuously. We reserve the right to change the product specification without notice.
