PLMR86B OWNER’S MANUAL Mobile Audio System 7/ MOD 8/ VOL + AS/PS SEL BAND VOL - DSP/0 9/ AUX IN 1 RESET 2INT 3RPT 4RDM 5DIR- 6DIR+ MUTE EQ
INSTALLATION Notes: Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
INSTALLATION Spring Washer Hex Nut tabs behind the dashboard to secure the sleeve in place. Metal Strap Mounting Bolt Plain Washer Dashboard Tapping Screw Tabs Screwdriver 9. Sleeve 6. Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables. 7. Slide the unit into the sleeve until it locks into place. 8. To further secure the unit, use the supplied metal strap to secure the back of the unit in place.
INSTALLATION Side View showing T, N Screw Screw Hook Dashboard or Console To fasten the unit to the factory radio mounting brackets. 1. Use a screwdriver to loose the hook’s screws on the front left and right sides of the unit and remove the hooks. 2. Align the screw holes on the bracket with the screw holes on the unit, and then tighten the screws (5x5mm) on each side. Note: the outer trim ring, sleeve and the metal strap are not used for method B installation.
WIRING CONNECTION
GENERAL OPERATION 1 2 3 4 22 6 7 8 5 9 7/ MOD 8/ VOL + AS/PS SEL BAND VOL - DSP/0 9/ AUX IN 1 2INT 3RPT 4RDM 5DIR- 19 18 17 16 15 14 MUTE EQ 6DIR+ RESET 21 20 SWITCHING ON/OFF THE UNIT Press any button to turn on the unit. When the unit is on, Press and hold button (1) to turn the unit off. SOUND ADJUSTMENT Press SEL button (3) shortly to select the desired adjustment mode.
GENERAL OPERATION Press MUTE button (9) to mute down the sound instantly. If any button is pressed in the mute state, the mute state is released. EQUALIZATION Press EQ button (10) shortly to turn on equalization function and to select desired audio mode. There are five kinds of mode as below: stations are stored into the corresponding preset number button. - Program scanning Press AS/PS button (6) shortly to scan preset station which is stored in button 16(1~6).
GENERAL OPERATION SD/MMC OPERATION or DIR + button (13). PAUSING PLAYING Press PAU button (19) to pause playing. Press it again to resume playing. PREVIEWING ALL FILES Press SCN button (18) to INTRO each file stored in USB device. Shortly press again to stop intro and start to play. REPEATING PLAYING Press RPT button (17) for 1 time. It will show “RPT ONE”. It will continuously repeat the same file. Press RPT button (17) for 2 times. It will show “RPT DIR”. It will repeat all files of the current directory.
REMOTE CONTROL HANDSET(OPTIONAL) FUNCTION KEY & CONTROL 1. POWER Power ON/OFF Button 2. MODE 3. TUNE/SKIP Mode Botton(S,T,U,7,For MP3/WMA Operation) 4. 5. 6. 7. 8. 9.
SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 kHz) : DC 12 Volts, Negative Ground : 178 (W) x 107 (D) x 50 (H) : ±10 dB : ±10 dB Maximum Output Power - Version Y : 4x50 watts Current Drain - 15 Ampere (max.) (For High Power Version) RADIO FM Frequency Coverage IF Sensitivity (S/N=30dB) 87.5 to 107.9 MHz 10.
TROUBLE SHOOTING Before going through the checklist, check wiring connection. If any of the problems persist after checklist has been made, consult your nearest service dealer. Symptom No power. Cause The car ignition switch is not on. Solution If the power supply is connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. The fuse is blown. Replace the fuse. Volume is in minimum Adjust volume to a desired level. Wiring is not properly connected.
