PLD71MU Motorized Slide Down and Detachable Panel 7-Inch Wide TFT Touch Screen Monitor Front panel USB port and AUX input Car DVD/VCD/MP4/CD/MP3 Player Built in AM/FM Tuner and RDS SD Card Slot in the panel
Contents Precautions .....................................2 Selecting Subtitles ..........................27 Safety Information......................... 3 Selecting multi-angle views .............. 27 Disc Notes .................................... 4 Title menu function .......................... 27 Installation .................................... 5 Setup .............................................28 Detaching the control panel .............. 7 General Setup ................................
Precautions THANK YOU FOR PURCHASING THIS CAR DVD PLAYER . Before operating the unit, read this manual thoroughly and keep it handy for future reference . To avoid injury or accident , read the following precautions before installing and operating the unit . ON INSTALLATION DO NOT install any receiver in locations where; - it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident.
Safety Information CAUTION: THIS DVD PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS DVD PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE . HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE DVD PLAYER CORRECTLY AS INSTRUCTED. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
Disc Notes Disc formats supported by this player DVD Audio and Video Disc size 12 cm VCD Audio and Video Disc size 12 cm CD Audio Disc size 12 cm MP3 Audio Disc size 12 cm Discs which cannot be played with this player DVD-RAM CDV CDG Handling and Cleaning Dirt, dust, scratches and warping disc will cause misoperation. Do not place stickers or make scratches on discs. Do not warp discs. A disc should always be kept in its case when not in use to prevent from damaging.
Installation NOTES: 1. Choose the mounting location where the unit will not interfere with the normal driving function of the driver. 2. Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. 3. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. 4.
Installation 3. Remove the PLASTIC COVER of the both sides away PLASTIC COVER 4. Insert the two KEY PLAT into the grooves at both sides of the unit as shown in figure until they click . KEY PLATE 5. Pulling the levers makes it possible to remove the unit from the dashboard .
Installation How To Remove And Install The Front Panel When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder. Detaching The Front Panel Before detaching the control panel, be sure to turn off the power. 1). Press the “REL” release button and the left hand side of front panel will release. RELEASE BUTTON 2). Pull-off the front panel and keep the front panel into the case .
Panel Angle Adjustment CHANGING THE CONTROL PANEL ANGLE When you want to change the viewing angle of the operating unit to play, you can touch the section on touch screen (or press the button on the front panel) repeatedly to select the desired angle as follows: ANGLE 1 - ANGLE 2 - ANGLE 3 - ANGEL 4 - ANGLE 1 . ANGLE 1 ANGLE 2 ANGLE 4 ANGLE 3 Caution: Do not insert your finger behind the control panel.
Electric Connection WIRING CONNECTION MAIN UNIT ISO CONNECTOR WHITE BROWN (B+)12V REAR CAMERA SWITCH (B-)PARKING BRAKE RADIO ANTENNA JACK YELLOW REAR CAMERA INPUT RCA CABLE FUSE IGNITION SWITCH(B+) REAR RCA OUTPUT CABLE RED BLACK COAXIAL OUT BROWN RCH RED LCH WHITE MEMORY YELLOW BACK-UP(B+) GROUND(B-) GREY SUBWOOFER VIDEO OUT 2 YELLOW FRONT RCA OUTPUT CABLE CHOKE BOX FRONT RCA RED R VIDEO OUT 1 YELLOW FRONT RCA WHITE L AUTO ANTENNA FUSE BLUE FRONT Lch SPK. REAR Lch SPK.
Remote Control DVD/RECEIVER CONTROL 15 MODE 17 7 2 MUTE PLAY/PAUSE 3 REPEAT ANGLE MO/ST 19 13 16 STOP 20 MENU EQ MODE 1 CLK 21 LO/DX 6 23 OSD 22 14 BAND 9 ENTER TITLE/PBC 18 A/PS VOL VOL 12 INT TOP 1 11 5 2 3 RDM 5 4 6 26 AF 10 SEL 8 7 9 25 TA 4 SETUP GOTO +10 0 8 Ref # Button 1 CLOCK 2 MODE 3 STOP 4 SETUP 5 24 Function Press it briefly to view the clock time , Press again to return to normal display mode . Press longer to set the time .
Remote Control Ref # Button 8 GOTO 9 / 10 SEL 11 VOL+/- 12 / / / 13 14 Function Press it button to begin playback at a moment in the program you designate. Use number buttons to enter the data that is needed. Press these buttons to skip ahead or back one track.
Remote Control Function Ref # Button These buttons are used for numeric entry in many different menus. In addition, in Radio Mode (when RDS is engaged), 0 serves as the TA button and 9 serves as the AF button. 24 0-9 25 +10 This button is used with the other number buttons for use with two-digit number entries. 26 1-6 Six numbered preset buttons store and recall stations for each band. Preparing the Remote Control Inserting the Battery 1.
Control Panel Key Functions Touch Panel CAR DVD/VCD/CD/MP3 PLAYER WITH MPEG4 SEL TOUCH SCREEN CH1-6 REL MODE MUTE ON DSP MOD VOL TA AF CLK VOLUME- LUD S-WOOFER SEL VOLUME+ RES IR AUX IN Touch Screen Key : MODE MUTE ON DSP Operating mode selection CLK Touch briefly show/hide clock, touch longer to set the clock .
Control Panel Unit Keys : 11 10 9 8 7 6 5 4 CAR DVD/VCD/CD/MP3 PLAYER WITH MPEG4 SEL TOUCH SCREEN CH1-6 REL MOD VOL RES 3 2 12 IR AUX IN 1 1 AUX Input JACK For information about connecting a AUX device, please see page 25 . 2 IR SENSOR 3 VOL+/ VOL- KNOB In normal mode, this knob is used to increase or decrease the volume. It is also used as an UP/DOWN knob when audio or video settings are being adjusted when accessed using the SELECT button.
Control Panel 6 REL BUTTON Press this button to release the front panel for removal . Refer to see page 7. 7 8 /CH 1-6 (RADIO PRESET) BUTTON A) In Disc Playback Mode Press this button to pause playback, press it again to resume playback. B) In Radio Mode you can store 30 stations in memory: 18 FM stations and 12 AM(MW) stations, each band stores up to six preset stations . -Store in Memory > Select the frequency band > Press repeatedly the button to select the desired memory key .
Basic Operation POWER On/Off Mute Function Press it to switch the device ON, press and hold about 2 seconds to switch the device OFF. MUTE ON Ejecting The Disc Use your finger to touch the range on touch screen , the control panel of the unit will swing downwards . Then you can insert the disc or eject the disc . (You can also press the button on the front panel to eject the disc or insert the disc to start play . ) Touch “MUTE ON” range, it will mute the sound but the disc continues playing .
Basic Operation Rear View Camera TFT Monitor Adjustment When connecting the rear view camera. the mirror image of the rear view through the rear view camera is automatically displayed on the monitor when you change the gear to the back position. (The monitor on the unit only.
Basic Operation Balance: R 0-10 to L 0-10 . Adjust sound balance between left and right speakers by using VOL + / - . Fader: F 0 - 10 to R 0 -10 . Adjust sound balance between front and rear speakers by using VOL + / VOL - . The RESET button is to be activated for the following reasons: A. Initial installation of the unit when all wiring is completed. B. All the function buttons do not operate. C. Error symbol on the display.
Radio Operation Listening to the Radio Start Searching For a Station Manual Search Switching To Radio Mode Touch the screen of “MODE” range (or press the MOD button on the front panel ) repeatedly to select the RADIO mode. the following information will appears as below: MODE FLAT Automatic Search 12:06 NO-DISC ST FM1 1 DX 87.60 MHZ MODE MUTE ON 2 VOLUME- 3 4 SEL FLAT 5 6 VOLUME+ 12:06 NO-DISC ST FM1 AF DX 87.
Radio Operation e.g. FM1, for the stronger signal level until the search cycle has finished . The six strongest stations are then allocated to the corresponding storage locations . Then the station of the first storage location is set . Storing Stations In Memory With this system, a total of 30 stations can be stored in the memory of six buttons. Each band stores up to six preset stations. The stations might be FM1, FM2, FM3, AM1(MW1), and AM2(MW2) band.
Radio Operation When the TA function is switched on , the FM traffic automatically interrupt CD operation(the word TRAFFIC appears in the display). The volume level is increased to the minimum value for the transmission of traffic announcements. Note : the status of the AF function is shown by an AF symbol in the display. If the AF symbol appears in the display, the AF function is switched on and RDS transmission date is being received .
DISC Operation Basic Operation Switching the DVD mode During DISC playback, you can touch the screen to display the following: Touch the screen of “MODE” range (or press MOD button on the front panel ) to select the DISC mode, it display like following : FLAT 12: 16 DISC-IN DVD 1-0:00:16 MODE FLAT 12: 16 DISC-IN MUTE ON DVD 1-0:00:16 MODE VOLUME- VOLUME+ SEL VOLUME- FLAT MUTE ON SEL VOLUME+ 12: 16 Function setup (different the source the display is different) DISC-IN DVD 1-0:00:16
DISC Operation Skipping Track Selecting The Play Modes During DISC playback, Touch the / section on the touch screen to skip to next/back one track. (You can also press the / on the front panel to skip to next /back one track.) During the Disc playback, touch the touch screen, it will display the following as below : FLAT DISC-IN DVD Note : 1. In DVD mode, touch the section continually twice to back one track . (Press the button continually twice to back one track .) 2. For some VCD2.
DISC Operation Each playing, the order is different . (Depend on the disc used for VCD). Touch it again to cancel this function . Note : in random mode, the button is not available . DISC Search (GOTO) FLAT DISC-IN DVD OSD FOR CD : Touch the screen of the “INTRO” section (or longer press the 3/INT button on the remote control ) to play the previous 6 seconds part of each track/chapter on disc.
DISC Operation 3) You now hear the sound from the external device played back through the loudspeakers . Note: Touch and hold the / section on the touch screen , you can select the title or chapter of DVD . (Only for the DVD with title /chapter.) 4) Touch the volume+/- sections on touch screen or use the VOL+/- on the remote to adjust the volume level. AUX Operation On the front panel of this unit, there is an AUX IN jack, follow the diagram below t o connect analogue replay devices.
DISC Operation ON-SCREEN DISPLAY FUNCTION OSD During playback, touch the screen the OSD section (or press the OSD on the remote), it will display the following as below : 2.Example for VCD/SVCD/CD: A.Touch or Press OSD for first time: SINGLE ELAPSED TRACK 01/16 0:00:56 1. DVD: A.Touch or Press OSD for first time: B.
DISC Special Functions DVD/VCD Special Function FLAT For VCD/CD: during playback, touch the AUDIO section of the touch screen or Press AUDIO on the remote . It is possible to switch the sound between monaural and stereo sound. 12: 16 DISC-IN DVD 1-0:00:16 RANDOM REPEAT AUDIO SUBTITLE SETUP INTRO MONO LEFT MIX-MONO TITLE 3. Multi-Angle Function (for DVD Only) Touch to select 1. Multi-subtitle Language Function (for DVD Only) During DVD playback.
Setup USING THE MENU GENERAL SETUP TV Setting DOLBY DOLBY ....GENERAL SETUP PAGE.... TV Display Angle Mark OSD Lang Spdif Output Captions Screen Saver Last Memor y ....GENERAL SETUP PAGE.... LB ON ENG SPDIF/RAW ON ON ON TV Display Display TV Angle Mark OSD Lang Spdif Output Captions Screen Saver Last Memor y Nor mal/PS Nor mal/LB Wide Go To General Setup Page Set TV Display Mode 1. Touch the screen of “ SETUP ” range or press the SETUP button on remote . 2.The SETUP menu is displayed. 3.
Setup GENERAL SETUP DOLBY DOLBY ....GENERAL SETUP PAGE.... ....GENERAL SETUP PAGE.... TV Display Angle Mark OSD Lang Spdif Output Captions Screen Saver Last Memor y TV Display Angle Mark OSD OSD Lang Lang Spdif Output Captions Screen Saver Last Memor y ON OFF SPDIF/OFF SPDIF/RAW SPDIF/PCM Setup SPDIF Set Angle Mark 2. ANGLE MARK DISPLAY SETUP If it is set to ON, when the multi-angle DVD disc is playing, (the angle mark) will appears on the screen; if is set to OFF, the mark will not appear. 4.
Setup GENERAL SETUP SPEAKER SETUP .....Speaker Setup Page..... DOLBY DOLBY ....GENERAL SETUP PAGE.... TV Display Angle Mark OSD Lang Spdif Output Captions Screen Saver Last Memor y ....Speaker Setup Page.... ON OFF Screen Saver Set Downmix Mode 6.SCREENSAVER SETUP If the screen displays a static image for too long, some "burn-in" may occur, leaving a permanent trace of the image behind. To avoid this, turn ON the SCREENSAVER item.
Setup --- PREFERENCES PAGE --DOLBY DOLBY ....Preference Page.... ....Preference Page.... TV Type Audio OSD Lang Subtitle Disc Menu Parental Password Default TV Type Audio OSD Lang Subtitle Disc Menu Parental Password Default PAL AUTO NTSC Set TV Standard English French Ger man Spanish Italian Por tuguese Off Prefer red Subtitle Language 1. TV TYPE SETUP This player is capable of playing discs recorded in either PAL or NTSC formats.
Setup --- PREFERENCES PAGE --Age control DOLBY DOLBY ....Preference Page.... ....Preference Page.... TV Type Audio OSD Lang Subtitle Disc Menu Parental Password Default TV Type Audio OSD Lang Subtitle 4PG13 5PGR 6R 7NC 17 8ADULT OFF Disc Menu Parental Password Default Set Parental Control RESET Load Factor y Setting 5.PARENTAL 7.
Other Main Operation USB Operation Changing From DISC to USB Playback Modes If the disc present in the player is an MP3 disc, touch section on screen or press the STOP on remote once then touch or press the GOTO to USB playback. If the disc present in the player is an DVD or VCD or CD disc, touch on the screen or press STOP twice on the remote then touch GOTO section on the screen or press the GOTO button on the remote to USB playback.
Other Main Operation SD/MMC card OPERATION The unit can support playback MP3/WMA/JPEG/MP4 and Divx format which are stored into SD and MMC memory card . Please read below before you start the operation of memory card . Inserting and removing a SD or MMC card on the front panel of unit . Inserting the SD or MMC card . Label side facing backward Insert the memory card into slot with label side facing backward . Press in till heard a “CLICK” . Removing the SD or MMC card . Remove the memory card .
Other Main Operation MP3/WMA/JPEG/MPEG4 DISC PLAY When you insert a disc which contains MP3, WMA or JPEG files, the different file types are detected, and a list of the files are produced, as shown in the diagram below. 5 4 3 00:56 2 003/112 1 04:07 Mp3 K Mp3 woman 1 Mp3 new ton 6 Repeat one P ....... ....... 1 Current track(file)(highlighted bar) 2 Current track (file) number/total number of tracks(files) in the current folder.
Specification Generall : Supply Voltage: Current Consumption: Signal System: Discs Played: 12V DC (11V-15V) Less than10 A Compositive video 1.
Trouble Shooting Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. SYMPTOM No power CAUSE SOLUTION The car ignition switch is not on The fuse is blown If the power supply is properly connected to the car accessory terminal,switch the ignition key to "ACC" Replace the fuse Presence of disc inside the Remove the disc in the player, then put a new one player.
