PLBT72G 7'' Single DIN In-Dash Motorized Touch Screen TFT/LCD Digital Monitor w/DVD/CD/MP4/USB/SD-Slot Card AM/FM/RDS/Bluetooth Compatible Dial Pad Built-In GPS/TTS w/USA/Canada & Mexico Maps USER MANUAL
To ensure safety while driving and to comply with laws, drivers should not watch video or operate the video device while driving.
PRECAUTION Class 1 laser product This car multi-media player is a class 1 laser product. However This car multi-media player uses a visible/invisible laser beam which could cause . Hazardous radiation exposure if directed. Be sure to operate the car multi-media player correctly as instructed. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not open covers and do not repair yourself.
Content Precaution......................................................................................... 1 Content............................................................................................. 2 Installation steps............................................................................... 3 General knowledge about remote control........................................... 7 Locations and Names of controls on main unit...................................
INSTALLATION STEPS 1.
REAR AUDIO OUTPUT CABLE RCH RED REAR CAMERA INPUT YELLOW SUBWOOFER GREY LCH WHITE FRONT AUDIO AND VIDEO OUTPUT CABLE RCH RED VIDEO OUT YELLOW LCH WHITE RADIO ANTENNA JACK GPS ANTENNA BOLT ISO CONNECTOR PINK IGNITION SWITCH(B+) MEMORY BACK-UP(B+) RED BROWN YELLOW GROUND(B-) BLUE BLACK FRONT LCH SPK. REAR LCH SPK. CHOKE BOX WHITE GREY WHITE/BLACK GREY/BLACK VIOLET GREEN GREEN/BLACK VIOLET/BLACK (B+)12V REAR CAMERA SWITCH (B-)PARKING BRAKE AUTO ANTENNA FRONT RCH SPK. REAR RCH SPK.
2) Attaching the control panel onto the chassis; (1) Insert the left side of the control panel into the hollow of the chassis . (NOTE : the “bulge” point on the control panel must be attached into the hollow of the chassis .) (2) Gently push the right side of the control panel till you feel a “ Click” . 1 Hollow 2 Bulge 3) Testing it for making sure that it can work properly . 4.
Installation Diagram DASH BOARD METAL MOUNTING STRAP HEX NUT SPRING WASHER PLAIN WASHER CONSOLE TAPPING SCREW SLIDE BRACKET HOUSING HEX BOLT SCREWDRIVER TABS KEY PLATE PLASTIC TRIM OUT KEY PLATE If you want to take CHASSIS out of the SLIDE BRACKET HOUSING, first remove the PLASTIC TRIM OUT of the both sides away, then insert the two KEY PLATE into left and right side of chassis as above illustration.
GENERAL KNOWLEDGE ABOUT REMOTE CONTROL 1. Removing insulating sheet If using remote control for the first time, you can see an insulating sheet at the bottom side of remote control as right. you must remove the insulating sheet as right. Otherwise, the remote control is disabled. 2. Replace lithium cell If the electric energy of lithium cell is weak, replace it.
Locations and Names of Controls on Main Unit 17 13 8 10 4 11 1 3 14 12 9 16 5 7 18 2 Control Panel 15 19 6 Ma in Unit Face after remo ving Control Panel 1. AUX IN JACK(A/V) 10. MUTE or PTY BUTTON 2. USB PORT 11. BAND or PAIR BUTTON 3. SEL BUTTON and VOL KNOB 12. >|| or CH1-6 BUTTON 4. REL BUTTON 13. >>| or HANG UP BUTTON 5. IR SENSOR WINDOW 14. |<< or CALL BUTTON 6. RESET BUTTON 15. SD/MMC CARD SLOT 7. EJECT BUTTON 16. LCD SREEN 8. POWER or MODE BUTTON 17.
Locations and Names of Controls on Remote Control 1 2 3 5 7 9 11 13 15 MUTE MODE PLAY/PAUSE 20 STOP MO/ST ZOOM 4 6 23 PAIR LOUD MENU EQ CLK LO/DX 8 10 25 27 OSD BAND 29 ENTER TITLE/PBC 12 2. MUTE BUTTON 21 REDIAL 31 A/PS 22 3. HANG UP or REDIAL BUTTON 4. MONITOR-ANGLE BUTTON 24 26 28 30 37 5. CALL or PAIR BUTTON 6. MENU or SW BUTTON 7. >> BUTTON 8. SUBTITLE or LO/DX BUTTON VOL TOP RPT INT 1 2 3 32 VOL RDM 6 33 10. BAND or OSD BUTTON 35 11.
Same functions in any work source mode 1. POWER button In power off mode, pressing POWER button on remote control or pressing POWER button on control panel powers on main unit. In power on mode, long pressing POWER button on control panel or on remote control powers off main unit. 2. VOL knob & VOL+/VOL- buttons To adjust volume level, rotate VOL knob on control panel or press or hold VOL+ or VOL- button on remote control. 3.
The home page of the source menu displays as follows: In the middle column, clock time displays in the top of it; the SN. And name of each page of the source menu display in the middle and bottom of it. Touch any place on the screen and hold and then slide leftwards or rightwards to turn pages of the source menu.
11.SYSTEM icon In the setup page of the source menu, touch SYSTEM icon to display page1 of SETTINGS MENU as follows: Page1 of SETTINGS MENU Page2 of SETTINGS MENU In the SETTINGS MENU, the icons on them descript as follows: : to next page. : to previous page. : to source menu. Setting Items : to enter the setting item. Page3 of SETTINGS MENU In the SETTINGS MENU, there are 10 setting items in all. Touch one setting item to enter the setting item page.
(4) BRIGHT It is for setting brightness. (5) CONTRAST It is for setting contrast. (6) COLOR It is for setting color. (7) TINT It is for setting tint. 2) SOUND SETTING Page1 of SOUND Page2 of SOUND (1) RADIO L/D It is for switching between LOC and DX. (2) STEREO It is for switching between MONO and STEREO. (3) SWF VOL It is for setting SWF volume. (4) SWF FREQ It is for setting SWF frequency. Page3 of SOUND (5) LOUDNESS It is for setting LOUDNESS mode. (6) SOUND EFFECT It is for setting EQ mode.
3) BACKGROUND SETTING BACKGROUND It is for setting the background of the No Video interface for RADIO, CD, non-CD DISC/USB /CARD, AUX and BT MUSIC . 4) RDS SETTING RDS (1) REG SET It is for setting REG on or off. (2) PI SET It is for switching between PI SOUND and PI MUTE. (3) AF SET It is for setting AF on or off. (4) TA SET It is for setting TA on or off. 5) GPS PATH SETTING GPS PATH It is for setting GPS path to enter GPS navigation mode.
6) TIME SETTING TIME (1) HOUR SET It is for setting the hour of the clock time. (2) MINUTE SET It is for setting the minute of the clock time. (3) TIME FORMAT It is for setting the time format of the clock time. 7) TOUCH SETTING TOUCH SCREEN CALIBRATION It is for calibrating touch screen. Precisely and repeatedly tap the center of the cross cusor till it exit calibration interface. 8) INFO SETTING SYSTEM INFO It is for viewing the system information such as: name, version, memory size and free momery.
9) SKIN SETTING SKIN (1) It is for setting the skin color of those immanent interfaces. (2) It is for setting the time of activating SCREEN SAVE after no operation. 10) ANGLE SETTING It is for setting the angle of the control panel. 12.RESET button When LCD displays wrongly or some buttons are not available or sound is distorted, press REL button to detach the control panel and remove it, then use the sharp end of a pointed object to press RESET button on chassis face to reset the program to zero. 13.
Radio Operation 1. To enter RADIO mode(MODE button or RADIO icon) When you use MODE button or source menu (tapping RADIO icon) to enter RADIO mode, it will display radio interface as follows: Radio interface * Radio interface with 1~6 icons interface Some icons on radio interface correspond with the buttons on remote control or control panel as follows: and icons = VOL- and VOL+ buttons = VOL knob MUTE icon = MUTE button List icon : to display 1~6 icons interface in the left side of the radio interface.
5. To preset and listen to a memory station(1~6 icons or 1~6 buttons or CH1-6 button ) 1) Long touching one of 6 number(1~6) icons or long pressing one of 6 number(1~6) buttons can preset the current broadcasting station of the current band in the number memory bank; . 2) Briefly touching one of 6 number(1~6) icons or briefly pressing one of 6 number(1~6) buttons can listen to the memory station in the current band preset in the number memory bank.
It switches over to the AF for a short time, and the AF icon is light on screen(not flash). * In FM mode, when switching on AF mode, the radio auto searches for or preset only those RDS stations. * In FM mode, when switching on AF and TA modes, the radio auto searches for only those RDS stations broadcasting traffic announcement. 10. REGION mode use the RDS interface of the SETTINGS MENU or the SEL and VOL buttons to set REGION mode on or off.
BT Operation 1. Pairing and Connecting Prior to using the BT device named BC_HF_V03 as a handfree system for a BTenabled mobile phone for the first time, you must pair and connect them as follows: * Prior to pairing and connecting, when displaying No Video interface of radio, CD, video disc, AUX or BT music, BT logo flashes in the top left corner of touch screen.
b. Use the number icons or buttons to input your desired phone number; * When inputting a wrong digit, use icon or < button to delete it. c. After finishing inputting, touch icon or press button on remote control to dial out. button on control panel or press 2) Redial last dialed phone number Touch icon or long press button on remote control to dial out the last dialed phone number.
and icons = VOL- and VOL+ buttons = VOL knob MUTE icon = MUTE button icon = icon = and button button icons = and button MUSIC icon: To enter source menu. MENU icon : To pop up the page1 of SETTINGS MENU MAP icon : To enter GPS mode but not exit BT music mode 2 ) When using your mobile phone with BT function to play audio/video , if it is paired and connected with the BT device of the car A/V system, the audio of the mobile phone will change into the car A/V system .
Disc/USB/Card Operation 1. Loading or unloading a disc, USB or card 1.1 Loading a disc, USB or card To play files in a disc, insert a disc with label surface up into disc slot. it will automatically play. * CAUTION OF USING DISC Label surface up 1) Handle a disc by its edge, do not touch the surface of play side. 2) Before inserting disc, wipe the disc outwards from the disc center with a clean, soft, dry, lint-free cloth. Do not use solvents /thinner such as petrol/benzine, cleaner.
1.2 Unloading a disc, USB or card To unload the disc in disc slot, use STOP button to stop playback and then press button to eject disc, then remove it. To pull away the USB storage, use STOP button to stop playback, then you can remove the USB storage.
The Function Icons-boards display as follows: Function Icons-board 1 Function Icons-board 2 * Some icons on the Function Icons-boards descript as follows: : Same as MUTE button. : Same as EQ button. : Same as VOL- button or rotating VOL knob with anti-clock wise. : Same as CLK button. : Same as long pressing EQ button. : Same as VOL+ button or rotating VOL knob with clock wise. : Same as SW button. : Poping up source Menu. : Switching AF mode on or off. : Poping up Function Icons-board 2.
3. Function of controls on the touch screen/main unit/remote control 1. icon or button During playback, use it to pause playback; in pause mode, use it to resume playback. In CD interface , the icon displays as 2. . icon or button During Digital Video/VCD/CD/MP3/WMA playback, tapping or pressing it pre-stop or pause playback; in pre-stop or pause mode, use icon or button to resume playback.
on control panel can fast backwards or forwards at the following multiple of normal speed: x2, x4, x8, x20, x1. During fast playback, use icon or button to resume normal playback. For image files, no this function. 4. / icons or buttons During playback, use one of them to play previous or next chapter/track. 5. Number buttons During Digital Video/VCD(PBC OFF)/MPEG4/Image/CD/MP3/WMA playback, use number buttons to input chapter/track SN. , then it will play or display it.
8. icon and GOTO button For Digital Video/MPEG4/VCD/image/MP3/WMA, you can use , , ,number and ENTER icons or GOTO, <, >, number and ENTER buttons to select a chapter /track or from a playback time point to play.
For MP3/WMA, icon and ZOOM button are disabled. For CD, the ZOOM button is disabled. 10. OSD icon or button During Digital Video /VCD /MPEG4/Image/MP3/WMA playback, use OSD icon or button to display playback information bar as bellows: Digital Video : MPEG4: VCD: Image: MP3/WMA: For CD , OSD button is disabled. 11. icon or REPEAT button During Digital Video playback, touch icon or long press RPT button to switch repeat mode between REP CHAPTER, REP TITLE, REP ALL and REP OFF.
During MP3/WMA/MPEG4/image playback, touch icon or long press RPT button to switch repeat mode between REP1,REP FOLDER(or DIR),REP ALL or REP OFF. During VCD(PBC ON) playback, icon and RPT button are disabled. 12. icon or RDM button During Digital Video/VCD(PBC OFF)/CD/MP3/WMA playback, tapping long pressing RDM button switches random mode on or off. For MPEG4/image/VCD(PBC ON) playback, 13. icon or INT button During VCD/CD playback, tapping intro mode on or off.
16. icon or SETUP button Use icon or SETUP button to enter Media Setup Menu for setting up all media parameter values. Use icon or SETUP button to display Media Setup Menu(the default page is SYSTEM SETUP); Media Setup Menu has 4 pages in all.
(1) 4:3 PS: Choose this item when connecting a monitor with 4:3 screen. When playing video with 16:9 size, the left and right part of video will be cut out, and video will display in full screen. (2) 4:3 LB: Choose this item when connecting a monitor with 4:3 screen. When playing video with 16:9 size, the top and bottom part of the monitor screen will be turned into a black square . (3) 16:9: Choose this item when connecting a monitor with 16:9 wide screen.
OSD LANGUAGE This item is for selecting the type of language displayed on the screen except for subtitle language and menu language(depending on current playing media). AUDIO LANG This item is for selecting the type of audio language(depending on current playing media). SUBTITLE LANG This item is for selecting the type of subtitle language(depending on current playing media). MENU LANG This item is for selecting the type of menu language(depending on current playing media).
4) DIGITAL SETUP DIGITAL SETUP DYNAMIC RANGE EXIT DYNAMIC RANGE This item is for adjusting linear compression ratio. If you set it to FULL, Peak-to-Peak value of audio signal is minimum; if you set it to OFF, Peak-to -Peak value is maximum.
* Region Code If you insert a disc into the disc slot and REGION ERROR is displayed, the car multi-media system can not play the disc. The reason is that the region codes of the car multi-media system and the used disc do not match each other. Appendix: Region code of D igital Video Motion Picture Association of America (MPAA) divided the world into 6 regions, and gave every region a region code for locking and unlocking D igital Video playback.
* Parental Control Q: After inserting a Digital Video disc into the disc slot, if a dialogue box pops up and asks you to input a password, what should you do ? A: The playing disc is locked by a rating level of parental control.
AUX IN operation An external AV system can use the car AV system as monitor and amplifier. AUX IN JACK DOM 1. Use an AV cable to make the car AV system and the external AV system connected through the AUX IN jack on control panel of the car AV system and the AV Out jacks of the external AV system. VIDEO IN (yellow) RCH IN (red) LCH IN (white) 2. Play the external AV system, then use MODE button or Source Menu to enter AUX IN mode for the car AV system.
External iPod operation An external iPod can use the car AV system as a monitor and amplifier. 1. Use the iPod cable to make the car AV system and the external iPod connected through the AUX IN jack on control panel of the car AV system and the headphone port of the external iPod. Head p ho n e p o rt 2. Play the external iPod, then use MODE button to enter AUX IN mode for the car AV system.
REAR VIEW CAMERA The car AV system can make you look at the actual status behind your car when you change the gear level to the back position. 1. Use an video cable to make the car AV system and the rear view camera connected through the REAR CAMERA INPUT jack in the rear cabinet of the car AV system and the VIDEO OUTPUT jack of the rear view camera. Make the REAR CAMERA SWITCH line in the rear cabinet of the car AV system connected to (B+)12V power supply. 2.
Operation of GPS module 1. GPS Navigation 1. Loading GPS card Before setting GPS path and entering GPS navigation mode, must load a GPS card with navigation map program file into the GPS card slot. firstly press REL button to detach control panel, then hold the right part of the control panel and pull upwards a little and to you to remove it, and then insert the GPS card with label side upward and contact end frontward into the GPS card slot as the following fig.
3. Entering GPS navigation mode. After loading a GPS card with an executable navigation map program file and set the GPS path to the executable navigation map program file, touch the GPS icon in the home page of the source menu or touch the MAP icon in the top right corner of the No Video interface of radio, CD, video disc, AUX or BT music to enter GPS navigation mode.
Photo Operation After loading a GPS card with photo files, touch PHOTO icon in the photo page of the source menu to enter photo mode and pop up the photo interface as follows: Photo interface GPS card path interface Photo list : to enter the GPS card path interface. : to enter. : to exit to photo interface. SDMEM : to enter the data folders list step by step and finally enter photo list. [..]: To return back to previous interface. Slide bar: to slide the photo list downward/upward or rightward/leftward.
: to enter the GPS card path interface. SDMEM : to enter the data folders list step by step and finally enter e-book list. File : to enter Reader interface again and display the e-book of this file. : to the home page. : to automatically slide page upward or stop sliding. : to the end page. : to previous page. : to next page. : to pop up the information interface of the current e-book. : to pop up the e-book setting interface. : to exit Reader interface to the tools page of the source menu.
Calculator and Calendar 1. Calculator Touch CAL icon in the tools page of the source menu to pop up calculator interface as follows: Calculator interface : to clear the number in the memory. : to display the number in the memory as inputting a number during arithmetic operation. : to store the current displaying number in the memory and display M in the left side of the display frame. : to make the current displaying number and the number in the memory plused and store it in the memory.
GAME 1. MINE Touch MINE icon in the games page of the source menu to pop up MINE game interface as follows: MINE game interface LINK game interface 2. LINK Touch LINK icon in the games page of the source menu to pop up LINK game interface as above. 3. FIVE CHESS Touch FIVE CHESS icon in the games page of the source menu to pop up FIVE CHESS game interface as follows: FIVE CHESS game interface BW CHESS game interface 4.
Troubleshooting Please read the user manual carefully before using the car A/V system. If you have any difficulty using this car A/V system, refer to the troubleshooting guide . If you are still unable to resolve the problem after using all the suggestions, please contact your dealer or an authorised service centre . * * NO PICTURE, SOUND Ensure that the power switch is on. Ensure that the power cord is not damaged or the fuse is not blown.
Specification General Power Supply Requirement..................................................DC 12V Current consumption........................................................10A MAX. Audio Signal Output ............................................................ 2ch&4ch line out Frequency Response................................................... 20 Hz - 20 KHz S/N Ratio ........................................................................... 90 dB (JIS) Wow and Flutter ............................
