Vintage Turntable With CD / Cassette / Radio / Aux-In / USB / SD / MP3 and Vinyl-to-MP3 Encoding PTCDS7UI www.PyleAudio.
Location of controls 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) 16) 17) 18) 19) 20) 21) 22) 23) 24) 25) 26) 27) 28) 29) 30) 31) 32) 33) Dial pointer LCD display Functions switch Power LED indicator Power on/off, volume up/down knob MP3 folder up button Source button Extra bass on/off button Record button CD door SD/MMC card slot Radio band selector switch FM stereo LED indicator Tuning knob Remote sensor Skip/search down button button Skip/search up CD door open button Play/pause/stop button USB so
Listening to radio Manual tuning 1. Select the desired band by Radio band selector (12) (AM or FM or FM-Stereo). 2. Tune to the required station by turning the Tuning knob (14). 3. Adjust volume knob (5) to the desire volume level. FM & FM-Stereo reception Set the Radio band selector (12) at “ FM ” position. Programs are received in mono mode. In particular when stereo signal are weak. It is preferable to receive the program in mono.
Remark:- In that case of no name had been assigned for the track, “ none “ or “ unknown “ is being displayed” on LCD display (2). - The system support English alphabet and numeral only for ID3 text Mp3 track format requirement:- Mp3 bit rate : 32 kbps~256 kbps. - The performance of playing MP3 disc is various from the quality of recording disc and the method of recording. Furthermore, the searching lead-time for MP3-CD is longer than normal CD due to difference format.
1. Set in CD/USB/SD mode & stop the cd/mp3 disc playback. 2. Press the “Program” button, “ PROG “ indicator will appear on LCD display (2). Moreover, it will indicate program no. and digits for track no. to be programmed. 3. Select a desired track by pressing skip or buttons (16,17). 4. Press the “ Program ” button to store the trace into memory. 5. Repeat steps 3 and 4 to enter additional tracks into the memory if necessary. 6.
Remark - Make sure the direction is correct when inserting the tape into the system. - There is some searching noise can be heard and the system cannot perform normal playback function during fast forward mode. - This is recommended to take out the cassette tape from the system every times after listening and don’t leave the cassette tape inside the system when not under playback mode. Phono noted: - Remove the stylus protector.
II) Recording the complete CD 1. Place a CD with the printed side facing up inside the CD tray & then close the CD door. 2. After disc search has been completed, press the “ Record “ button (9) – note: for recording whole CD, do not press “ Play/Pause/Stop ” button (19) before press " Record " button(except in Recording in program mode) as this procedure will only record the first track of the CD. 3. “ “&“ “ will be flashing on the LCD display (2) to show encoding is in progress. 4.
I) Copying 1 track (assume copy from SD card to USB mode) 1. Perform normal playback of the track at SD/MMC card you want to copy, 2. Press “ Record “ button (9) during the playback of the desire track, unit will display “ “ and flashing. Copying is performing now. 3. After copying is completed, unit will stop playback automatically. “&“ II) Copying all tracks (assume copy from SD card to USB mode) 1. Select “ SD “ mode and then insert the S/MMC card you want to copy. 2.
Remote control transmitter Battery installation (battery not provided) The infra-red transmitter requires 2 pcs AAA size battery for operation Button description 1) Find In MP3 playback, press to active file/folder name search function.
