User's Manual

8.1 Countdown Timer Mode -
Setting the Timer
8.0 Countdown Timer Mode -
Countdown Timer Mode
To Set the Countdown Timer
- Press and hold the [mode] button for 2 seconds to
change the display from Countdown Timer Mode to
Countdown Timer Setting Mode.
NOTE: The setting range of the timer: 0 to 99 hours, 59
minutes, 59 seconds.
- The second digits flash on the display because it is
being selected.
The Setting Procedure
- Press [mode] button to change the selection following
the Countdown Timer Setting Sequence.
- If the digits are flashing, press the [start/stop] button
to increase the number; hold the [start/stop] button to
change the number at a higher speed. Press the
[compass] button to decrease the number; hold the
[compass] button to change the number at a higher
speed.
- After you set the timer, press the [mode] button to
exit the setting sequence.
- If no key-stoke has been activated for 30 seconds, the
setting display will return to Countdown Timer Mode.
Countdown Timer
- HandHeld TrackMaster has countdown feature: the
Countdown Timer Mode.
- The Countdown Timer starts counting from the
preset number to zero and stops at zero.
- The 1st row of the display shows the ' CdT'
indicator.
- The 2nd row of the display shows the countdown time:
hour, minute and second.
- The indicators encircled the display shows the
countdown
time in 1 second analogically.
To Use the Timer
- Once the timer has been set (for example 0:10 15), press
the [start/stop] button once to start the countdown. The
countdown time will be displayed continuously
throughout the countdown.
- To stop countdown, press the [start/stop] button once.
- When the countdown time is come to zero, press
[compass] button to re-load the preset time, or press
[start/stop] button to re-load the preset time and
starts the countdown simultaneously.
To Reset the Timer
- To reset the timer to zero, press and hold the [compass]
button for 2 seconds when the timer has stopped
counting.
Timer Alarm Sound
- The timer starts to beep twice when the countdown time
comes to 10,5,4,3,2,1 minute(s) and 50,40,30,20,10
seconds.
- The timer starts to beep once when the countdown time
comes to 9, 8,7,6,5,4,3,2,1 second(s).
- The timer starts to beep a long beep when
the countdown time comes to zero.
To Use the Pacer
- The HandHeld TrackMaster build-in a pacer for the user:
The Pacer Mode.
- The 2nd row of the display show the current pacer
setting.
- The ' PACE' indicator will be appeared on the 3rd
row of the display.
- If the pacer is activated, the HandHeld TrackMaster
will beep at the preset rate (bpm) for every
minute.
To Start/Stop the
Pacer
- If the Pacer has been set, press the [start/stop] button to
start the pacer. If the Pacer started, press the
[start/stop] button again to stop the pacer and the
beeping sound.
8.2 Countdown Timer Mode
- Using the Timer
9.0 Pacer Mode -
Using the Pacer
second minute
hour
Alarm Time Setting Sequence
hold
[mode]
[mode]
[mode]
[mode]
Increase
the number
increase the
number at
a higher speed
[start/stop] hold [start/stop]
decrease
the number
decrease the
number at
a higher speed
hold [compass][compass]
hold
mode
Countdown Timer Setting Mode Countdown Timer
'running' Mode
Countdown Timer Mode Countdown Timer Mode
digits have been
selected (flashing)
digits have been
selected (flashing)
analogue
second
analogue
second
countdown
time
Pre-set
countdown time
the countdown
time
the number
of bpm
(Beep per
minute)
Countdown
Timer Mode
indicator
Countdown
Timer Mode
indicator
Pacer Mode
indicator
[start/stop]
hold [mode]
Pacer Setting Mode
Pacer Mode
13
14
15
16